Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor and the seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC Code Detection Condition Trouble Area
B1653/35 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.

·

Seat position airbag sensor malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat inner belt assembly LH

·

Seat position airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C162307E04
1.1,1.561 1.322,1.708 0.222,0.147 10 VS 1.036,2.407 1.383,2.568 0.347,0.160 10 GND 0.861,3.861 1.162,4.023 0.301,0.162 10 O4 0.871,4.018 2.399,4.174 1.529,0.156 10 Front Seat Inner Belt LH 0.6,3.177 2.442,3.333 1.842,0.156 10 Seat Position Airbag Sensor 2.988,2.853 3.095,2.998 0.106,0.145 10 4 2.185,1.356 2.311,1.521 0.126,0.165 10 2 2.954,1.388 3.077,1.536 0.123,0.148 10 2 2.171,2.844 2.293,2.992 0.123,0.148 10 1 5.392,1.388 5.586,1.542 0.194,0.154 10 14 5.722,1.233 6.138,1.400 0.416,0.167 10 DSP+ 5.418,2.878 5.621,3.062 0.203,0.184 10 13 5.736,2.742 6.110,2.901 0.374,0.159 10 DSP- 2.491,1.366 2.907,1.533 0.416,0.167 10 LSP+ 2.505,2.847 2.879,3.006 0.374,0.159 10 LSP- 5.427,3.815 5.741,3.985 0.314,0.170 10 O1 5.427,3.973 6.793,4.134 1.366,0.161 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the seat position airbag sensor.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and the seat position airbag sensor.


b.

Check that the connectors (on the center airbag sensor side and seat position airbag sensor side) are not damaged (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connectors are not deformed or damaged.




OK

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR)

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (CENTER AIRBAG SENSOR - SEAT POSITION AIRBAG SENSOR)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U153545E01
1.028,1.555 1.166,1.739 0.139,0.184 10 D 0.777,1.555 0.915,1.739 0.139,0.184 10 E 0.486,1.353 0.624,1.537 0.139,0.184 10 F 1.15,1.555 1.362,1.757 0.211,0.202 10 C 1.421,1.555 1.651,1.766 0.230,0.211 10 B 1.697,1.342 1.937,1.544 0.239,0.202 10 A 1.512,1.827 2.428,2.154 0.915,0.327 10 Center Airbag Sensor 0.016,1.784 0.965,2.123 0.949,0.339 10 Seat Position Airbag Sensor 2.294,0.251 4.710,0.611 2.416,0.361 10 Front view of wire harness connector: (to Seat Position Airbag Sensor) 4.755,0.251 7.074,0.611 2.319,0.361 10 Rear view of wire harness connector: (to Center Airbag Sensor) 4.903,1.23 5.229,1.395 0.326,0.165 10 O1 3.807,1.498 4.681,1.640 0.873,0.142 10 Connector E 6.164,1.497 6.973,1.653 0.809,0.156 10 Connector B 4.741,2.223 5.187,2.372 0.446,0.149 10 DSP+ 5.984,2.223 6.397,2.393 0.413,0.170 10 DSP- 5.61,1.895 6.097,2.22 false 5.497,1.9 5.021,2.207 false 5.709,2.523 6.541,2.693 0.832,0.170 10 Service Wire 5.634,2.261 5.802,2.511 false


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch ON Below 1 V
2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always 1 MΩ or higher
1 - Body ground Always 1 MΩ or higher
2 - Body ground Always 1 MΩ or higher




OK

4.CHECK SEAT POSITION AIRBAG SENSOR

NG

7.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
4.CHECK SEAT POSITION AIRBAG SENSOR
a.
C162325E01
1.897,1.142 2.812,1.446 0.915,0.304 10 Center Airbag Sensor 0.442,1.071 1.401,1.410 0.959,0.339 10 Seat Position Airbag Sensor

Connect the connectors to the center airbag sensor and the seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




OK

NG

5.REPLACE SEAT POSITION AIRBAG SENSOR
5.REPLACE SEAT POSITION AIRBAG SENSOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the seat position airbag sensor (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL).

HINT:

Perform inspection using parts from a normal vehicle if possible.




NEXT

6.CHECK CENTER AIRBAG SENSOR
6.CHECK CENTER AIRBAG SENSOR
a.
C162325E01
1.897,1.142 2.812,1.446 0.915,0.304 10 Center Airbag Sensor 0.442,1.071 1.401,1.410 0.959,0.339 10 Seat Position Airbag Sensor

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.




OK

END

NG

7.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
a.

Disconnect the floor wire connector from the front seat inner belt LH.

U153565E02
3.563,1.729 3.917,1.563 true 3.563,1.896 3.917,2.073 false 3.563,1.896 3.917,2.073 true 1.417,1.385 1.417,0.875 1.417,0.875 1.292,0.875 false 5.583,1.896 6.063,2.219 true 5.5,1.896 5.021,2.208 true 5.635,2.26 5.802,2.51 false 0.969,1.51 0.969,2.417 false 0.594,0.792 1.271,0.938 0.677,0.146 10 false Floor Wire 1.063,1.542 1.198,1.729 0.135,0.188 10 false D 0.781,1.542 0.917,1.729 0.135,0.188 10 false E 0.49,1.365 0.625,1.552 0.135,0.188 10 false F 1.208,1.542 1.417,1.74 0.208,0.198 10 false C 1.49,1.542 1.719,1.75 0.229,0.208 10 false B 1.771,1.365 2.01,1.563 0.24,0.198 10 false A 1.563,1.823 2.479,2.135 0.917,0.313 10 false Center Airbag Sensor 0.24,2.438 1.802,2.604 1.563,0.167 10 false Front Seat Inner Belt LH 0.021,1.76 1.01,2.083 0.99,0.323 10 false Seat Position Airbag Sensor 2.302,0.177 4.719,0.542 2.417,0.365 10 false Front view of wire harness connector: (to Front Seat Inner Belt LH) 4.75,0.177 7.073,0.542 2.323,0.365 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.708,1.229 2.979,1.427 0.271,0.198 10 false O4 4.906,1.229 5.229,1.396 0.323,0.167 10 false O1 3.958,2.063 4.385,2.219 0.427,0.156 10 false LSP- 3.948,1.469 4.375,1.625 0.427,0.156 10 false LSP+ 3.76,1.104 4.635,1.25 0.875,0.146 10 false Connector C 6.167,1.5 6.979,1.656 0.813,0.156 10 false Connector B 4.74,2.219 5.188,2.365 0.448,0.146 10 false DSP+ 5.979,2.219 6.396,2.385 0.417,0.167 10 false DSP- 5.708,2.521 6.542,2.688 0.833,0.167 10 false Service Wire


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O4-2 (LSP+) - Body ground Ignition switch ON Below 1 V
O4-4 (LSP-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 13 (DSP-) and 14 (DSP+) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-2 (LSP+) - O4-4 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O4-2 (LSP+) - O4-4 (LSP-) Always 1 MΩ or higher
O4-2 (LSP+) - Body ground Always 1 MΩ or higher
O4-4 (LSP-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPLACE FLOOR WIRE