Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1865/65  Short in Front Passenger Side Knee Airbag Squib Circuit  B1866/65  Open in Front Passenger Side Knee Airbag Squib Circuit  B1867/65  Short to GND in Front Passenger Side Knee Airbag Squib Circuit  B1868/65  Short to B+ in Front Passenger Side Knee Airbag Squib Circuit  


DESCRIPTION

The front passenger side knee airbag squib circuit consists of the center airbag sensor and front passenger side knee airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.

DTC Code Detection Condition Trouble Area
B1865/65 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front passenger side knee airbag squib circuit during the primary check.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1866/65 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front passenger side knee airbag squib circuit for 2 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1867/65 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front passenger side knee airbag squib circuit for 0.5 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly


B1868/65 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front passenger side knee airbag squib circuit for 0.5 seconds.

·

A front passenger side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Front passenger side knee airbag assembly (Front passenger side knee squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146265E14
0.754,2.937 1.142,3.135 0.387,0.198 10 H112 0.754,3.091 3.382,3.275 2.628,0.184 10 Front Passenger Side Knee Airbag 2.103,1.52 2.397,1.685 0.295,0.165 10 PK+ 2.137,2.52 2.395,2.685 0.258,0.165 10 PK- 2.475,2.271 2.613,2.427 0.137,0.156 10 2 2.464,1.484 2.602,1.677 0.137,0.193 10 1 4.517,1.509 4.714,1.702 0.198,0.193 10 19 4.537,2.314 4.711,2.461 0.174,0.147 10 20 4.817,1.585 5.131,1.759 0.313,0.174 10 PK+ 4.817,2.416 5.131,2.590 0.313,0.174 10 PK- 4.907,4.079 5.202,4.226 0.295,0.147 10 H56 4.908,4.24 6.286,4.433 1.378,0.193 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER SIDE KNEE AIRBAG (FRONT PASSENGER SIDE KNEE SQUIB)
U153553E02
1.99,3.771 2.417,3.917 false 0.917,0.646 0.688,1.115 false 0.25,2.229 2.646,2.583 2.396,0.354 10 false Front view of wire harness connector: (to Front Passenger Side Knee Squib) 1.625,1.073 2.99,1.219 1.365,0.146 10 false Center Airbag Sensor 0.042,1.135 1.208,1.51 1.167,0.375 10 false Front Passenger Side Knee Squib 1.01,0.729 1.146,0.885 0.135,0.156 10 false D 1.24,0.729 1.365,0.885 0.125,0.156 10 false C 2.177,3.146 3.01,3.313 0.833,0.167 10 false Connector C 2.438,3.865 2.771,4.031 0.333,0.167 10 false SST 0.469,3.583 0.833,3.75 0.365,0.167 10 false H112

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front passenger side knee airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front passenger side knee airbag (front passenger side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the instrument panel wire connector (on the front passenger side knee airbag side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE KNEE SQUIB CIRCUIT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER SIDE KNEE SQUIB CIRCUIT)
U153556E01
0.245,2.348 2.620,2.711 2.375,0.363 10 Front view of wire harness connector: (to Front Passenger Side Knee Squib) 1.743,1.078 3.097,1.244 1.354,0.166 10 Center Airbag Sensor 0.688,1.661 2.834,1.862 2.146,0.201 10 Front Passenger Side Knee Squib 1.209,0.709 1.346,0.883 0.137,0.174 10 D 1.395,0.709 1.551,0.855 0.156,0.147 10 C 2.133,0.502 2.270,0.668 0.137,0.165 10 A 1.772,0.714 1.911,0.898 0.139,0.184 10 B 2.138,3.23 3.081,3.386 0.943,0.156 10 Connector C 2.187,3.673 2.497,3.815 0.310,0.142 10 PK- 0.536,3.673 0.852,3.815 0.316,0.142 10 PK+ 0.907,3.707 1.431,3.595 false 1.603,3.595 2.161,3.707 false 0.422,3.221 0.771,3.371 0.350,0.149 10 H112 0.049,0.032 1.445,0.211 1.396,0.179 10 Instrument Panel Wire 1.651,0.504 1.883,0.124 1.883,0.124 1.769,0.124 false

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H112-1 (PK+) - Body ground Ignition switch ON Below 1 V
H112-2 (PK-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H112-1 (PK+) - H112-2 (PK-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H112-1 (PK+) - H112-2 (PK-) Always 1 MΩ or higher
H112-1 (PK+) - Body ground Always 1 MΩ or higher
H112-2 (PK-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK CENTER AIRBAG SENSOR
C146268E05
0.108,1.675 2.263,1.824 2.156,0.149 10 Front Passenger Side Knee Squib 1.504,1.257 2.901,1.457 1.397,0.200 10 Center Airbag Sensor 0.876,1.675 0.876,0.773 false 0.968,0.83 1.124,0.996 0.156,0.165 10 D 1.105,0.833 1.261,1.007 0.156,0.174 10 C

a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front passenger side knee airbag and center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1865, B1866, B1867 or B1868 is not output.


HINT:

Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.




OK

NG