Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Driver Side Pretensioner Squib Circuit  B1901/73  Open in Front Driver Side Pretensioner Squib Circuit  B1902/73  Short to GND in Front Driver Side Pretensioner Squib Circuit  B1903/73  Short to B+ in Front Driver Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and the front seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code Detection Condition Trouble Area
B1900/73 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib LH circuit during primary check.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1901/73 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1902/73 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1903/73 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C157591E59
1.137,3.534 1.430,3.694 0.292,0.159 10 O9 1.137,3.701 2.578,3.859 1.441,0.159 10 Front Pretensioner LH 4.612,4.697 4.907,4.856 0.295,0.159 10 O1 4.682,3.028 5.041,3.187 0.359,0.159 10 PD- 4.471,3.133 4.660,3.293 0.189,0.159 10 1 4.682,2.187 5.060,2.347 0.378,0.159 10 PD+ 2.4,2.935 2.580,3.078 0.181,0.143 10 L- 2.355,2.094 2.577,2.253 0.222,0.159 10 L+ 4.475,2.293 4.584,2.452 0.109,0.159 10 2 2.696,3.133 2.805,3.293 0.109,0.159 10 2 2.696,2.293 2.805,2.452 0.109,0.159 10 1 4.612,4.863 5.974,5.041 1.362,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the front seat outer belt LH.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the front seat outer belt LH.


e.

Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
a.
U153551E02
1.99,3.771 2.417,3.917 false 0.917,0.656 0.688,1.125 false 0.156,2.229 2.552,2.583 2.396,0.354 10 false Front view of wire harness connector: (to Front Pretensioner Squib LH) 1.625,1.073 2.99,1.219 1.365,0.146 10 false Center Airbag Sensor 0.031,1.135 1.198,1.51 1.167,0.375 10 false Front Pretensioner Squib LH 1.01,0.729 1.146,0.885 0.135,0.156 10 false D 1.24,0.729 1.365,0.885 0.125,0.156 10 false C 2.177,3.146 3.01,3.313 0.833,0.167 10 false Connector C 2.438,3.865 2.771,4.031 0.333,0.167 10 false SST 0.448,3.563 0.698,3.729 0.25,0.167 10 false O9

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1900, B1901, B1902, B1903 or 73 is not output.


HINT:

Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.
U153554E01
0.168,2.348 2.542,2.711 2.375,0.363 10 Front view of wire harness connector: (to Front Pretensioner Squib LH) 1.743,1.078 3.097,1.244 1.354,0.166 10 Center Airbag Sensor 0.688,1.661 2.520,1.862 1.832,0.201 10 Front Pretensioner Squib LH 1.209,0.709 1.346,0.883 0.137,0.174 10 D 1.395,0.709 1.551,0.855 0.156,0.147 10 C 2.133,0.502 2.270,0.668 0.137,0.165 10 A 1.772,0.714 1.911,0.898 0.139,0.184 10 B 2.138,3.23 3.081,3.386 0.943,0.156 10 Connector C 2.187,3.673 2.392,3.815 0.205,0.142 10 L- 0.639,3.673 0.872,3.815 0.232,0.142 10 L+ 0.907,3.707 1.431,3.595 false 1.603,3.595 2.161,3.707 false 0.617,3.29 0.870,3.439 0.253,0.149 10 O9 0.714,0.032 1.384,0.211 0.670,0.179 10 Floor Wire 1.651,0.504 1.651,0.124 1.651,0.124 1.537,0.124 false

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O9-1 (L+) - Body ground Ignition switch ON Below 1 V
O9-2 (L-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (L+) - O9-2 (L-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O9-1 (L+) - O9-2 (L-) Always 1 MΩ or higher
O9-1 (L+) - Body ground Always 1 MΩ or higher
O9-2 (L-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C146268E19
0.552,1.24 0.865,0.792 false 0.031,1.271 1.219,1.656 1.188,0.385 10 false Front Pretensioner Squib LH 1.625,1.25 2.5,1.583 0.875,0.333 10 false Center Airbag Sensor 0.958,0.854 1.115,1.021 0.156,0.167 10 false D 1.094,0.854 1.25,1.031 0.156,0.177 10 false C

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt LH and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1900, B1901, B1902, B1903 or 73 is not output.


HINT:

Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.




OK

NG