Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Passenger Side Pretensioner Squib Circuit  B1906/74  Open in Front Passenger Side Pretensioner Squib Circuit  B1907/74  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908/74  Short to B+ in Front Passenger Side Pretensioner Squib Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor and the front seat outer belt RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC Code Detection Condition Trouble Area
B1905/74 When one of following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib RH circuit during primary check.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1906/74 When one of following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front pretensioner squib RH circuit for 2 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1907/74 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly


B1908/74 When one of following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds.

·

Front pretensioner squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C157591E60
1.109,3.534 1.429,3.694 0.320,0.159 10 P8 1.109,3.701 2.550,3.859 1.441,0.159 10 Front Pretensioner RH 4.584,4.725 4.913,4.884 0.330,0.159 10 P1 4.682,3.028 5.041,3.187 0.359,0.159 10 PP- 4.463,3.133 4.570,3.293 0.107,0.159 10 5 4.682,2.187 5.060,2.347 0.378,0.159 10 PP+ 2.4,2.935 2.580,3.078 0.181,0.143 10 R- 2.355,2.094 2.577,2.253 0.222,0.159 10 R+ 4.461,2.293 4.570,2.452 0.109,0.159 10 4 2.696,3.133 2.805,3.293 0.109,0.159 10 2 2.696,2.293 2.805,2.452 0.109,0.159 10 1 4.584,4.891 5.985,5.069 1.401,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connector is properly connected to the front seat outer belt RH.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the front seat outer belt RH.


e.

Check that the No. 2 floor wire connector (on the front seat outer belt RH side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

2.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)

NG

REPLACE NO. 2 FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
a.
U153557E02
2.135,3.417 2.521,3.656 false 0.271,2.01 2.677,2.354 2.406,0.344 10 false Front view of wire harness connector: (to Front Pretensioner Squib RH) 2.26,2.917 3.156,3.115 0.896,0.198 10 false Connector C 2.563,3.583 2.906,3.75 0.344,0.167 10 false SST 0.667,3.094 0.958,3.26 0.292,0.167 10 false P8 1.49,1.26 2.844,1.417 1.354,0.156 10 false Center Airbag Sensor 0.24,0.052 1.438,0.417 1.198,0.365 10 false Front Pretensioner Squib RH 1,1.229 1.146,1.406 0.146,0.177 10 false D 1.188,1.219 1.344,1.396 0.156,0.177 10 false C

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the connector is properly connected to the center airbag sensor assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



e.

Disconnect the connector from the center airbag sensor assembly.


f.

Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.



g.

Check that the short spring for the No. 2 floor wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
U153558E02
1.167,3.844 1.625,3.448 false 1.781,3.448 2.26,3.844 false 0.802,1.229 0.698,1.958 0.698,1.958 0.885,1.958 false 1.427,1.115 1.427,0.542 1.427,0.542 1.333,0.542 false 0.979,1.854 2.833,2.052 1.854,0.198 10 false Front Pretensioner Squib RH 1.698,1.406 3.063,1.573 1.365,0.167 10 false Center Airbag Sensor 1.125,1.313 1.26,1.479 0.135,0.167 10 false C 0.896,1.313 1.031,1.479 0.135,0.167 10 false D 1.521,1.313 1.646,1.469 0.125,0.156 10 false B 1.875,1.083 2,1.24 0.125,0.156 10 false A 2.188,3.292 2.99,3.438 0.802,0.146 10 false Connector C 2.281,3.76 2.552,3.906 0.271,0.146 10 false R- 0.917,3.76 1.115,3.906 0.198,0.146 10 false R+ 0.24,0.469 1.271,0.635 1.031,0.167 10 false No. 2 Floor Wire 0.938,3.24 1.229,3.385 0.292,0.146 10 false P8 0.24,2.375 2.656,2.698 2.417,0.323 10 false Front view of wire harness connector: (to Front Pretensioner Squib RH)

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P8-1 (R+) - Body ground Ignition switch ON Below 1 V
P8-2 (R-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-1 (R+) - P8-2 (R-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-1 (R+) - P8-2 (R-) Always 1 MΩ or higher
P8-1 (R+) - Body ground Always 1 MΩ or higher
P8-2 (R-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C146261E58
0.823,1.104 0.625,1.479 false 0.031,1.51 1.219,1.906 1.188,0.396 10 false Front Pretensioner Squib RH 0.958,1.208 1.083,1.406 0.125,0.198 10 false D 1.104,1.208 1.25,1.396 0.146,0.188 10 false C 1.625,1.281 2.542,1.438 0.917,0.156 10 false Airbag Sensor

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt RH and the center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.


HINT:

Codes other than DTC B1905, B1906, B1907, B1908 and 74 may be output at this time, but they are not related to this check.




OK

NG