Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27L0U _58 Vehicle Interior _049341 SUPPLEMENTAL RESTRAINT SYSTEMS _0235848 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B181A/7A  Short in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181B/7A  Open in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181C/7A  Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit  B181D/7A  Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit  


DESCRIPTION

The variable vent hole squib circuit consists of the center airbag sensor and front passenger airbag.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the variable vent hole squib circuit.

DTC Code Detection Condition Trouble Area
B181A/7A When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the variable vent hole squib circuit during primary check.

·

Variable vent hole squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire assembly

·

Front passenger airbag assembly (Variable vent hole squib)

·

Center airbag sensor assembly


B181B/7A When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the variable vent hole squib circuit for 2 seconds.

·

Variable vent hole squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire assembly

·

Front passenger airbag assembly (Variable vent hole squib)

·

Center airbag sensor assembly


B181C/7A When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the variable vent hole squib circuit for 0.5 seconds.

·

Variable vent hole squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire assembly

·

Front passenger airbag assembly (Variable vent hole squib)

·

Center airbag sensor assembly


B181D/7A When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the variable vent hole squib circuit for 0.5 seconds.

·

Variable vent hole squib malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire assembly

·

Front passenger airbag assembly (Variable vent hole squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C353059E04
3.323,1.208 3.781,1.406 0.458,0.198 10 false Hz2 3.333,2.427 3.823,2.625 0.49,0.198 10 false Hz2 3.385,0.979 3.542,1.177 0.156,0.198 10 false 1 3.406,2.198 3.563,2.396 0.156,0.198 10 false 2 1.667,1.094 1.823,1.292 0.156,0.198 10 false 1 1.667,2.302 1.823,2.5 0.156,0.198 10 false 2 1.281,1.094 1.594,1.292 0.313,0.198 10 false P2+ 1.281,2.302 1.594,2.5 0.313,0.198 10 false P2- 5.885,1.156 6.271,1.354 0.385,0.198 10 false VHP+ 5.906,2.344 6.323,2.531 0.417,0.188 10 false VHP- 5.583,1.073 5.781,1.26 0.198,0.188 10 false 11 5.563,2.313 5.771,2.51 0.208,0.198 10 false 12 0.302,3.313 0.615,3.51 0.313,0.198 10 false z15 0.292,3.5 4.271,3.698 3.979,0.198 10 false Variable Vent Hole Squib 5.542,3.271 6,3.469 0.458,0.198 10 false H56 5.531,3.448 6.917,3.667 1.385,0.219 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER AIRBAG (VARIABLE VENT HOLE SQUIB)
U153444E02
0.531,0.802 0.385,1.438 false 1.854,4.177 2.26,4.313 false 2.094,3.677 2.51,3.802 false 0.177,1.427 1.479,1.792 1.302,0.365 10 false Variable Vent Hole Squib 1.688,1.573 3.094,1.781 1.406,0.208 10 false Center Airbag Sensor 0.667,0.896 0.813,1.073 0.146,0.177 10 false F 0.875,0.875 1.021,1.052 0.146,0.177 10 false E 1.24,0.885 1.385,1.063 0.146,0.177 10 false D 1.365,0.885 1.51,1.063 0.146,0.177 10 false C 0.479,2.333 2.74,2.771 2.26,0.438 10 false Front view of wire harness connector: (to Variable Vent Hole Squib) 0.708,3.646 0.969,3.833 0.26,0.188 10 false z15 2.323,3.167 3.208,3.354 0.885,0.188 10 false Connector E 2.604,3.677 2.917,3.854 0.313,0.177 10 false SST 2.323,4.24 3.24,4.448 0.917,0.208 10 false Color: Orange

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the front passenger airbag (variable vent hole squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B181A, B181B, B181C or B181D is not output.


HINT:

Codes other than DTC B181A, B181B, B181C and B181D may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the instrument panel wire connectors (on the front passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE ASSEMBLY

3.CHECK VARIABLE VENT HOLE SQUIB CIRCUIT
a.
U153446E02
0.635,0.833 0.521,1.51 false 1.51,3.49 1.125,3.76 true 1.625,3.49 2.01,3.76 true 1.771,4.177 2.188,4.302 false 0.292,1.594 1.458,1.99 1.167,0.396 10 false Variable Vent Hole Squib 2.104,1.615 2.979,1.938 0.875,0.323 10 false Center Airbag Sensor 0.76,0.906 0.906,1.083 0.146,0.177 10 false F 0.958,0.896 1.104,1.073 0.146,0.177 10 false E 1.833,0.906 1.979,1.083 0.146,0.177 10 false B 2.219,0.667 2.365,0.844 0.146,0.177 10 false A 1.344,0.896 1.49,1.073 0.146,0.177 10 false D 1.458,0.896 1.604,1.073 0.146,0.177 10 false C 0.542,2.469 2.917,2.813 2.375,0.344 10 false Front view of wire harness connector: (to Variable Vent Hole Squib) 0.604,3.375 0.865,3.563 0.26,0.188 10 false z15 2.135,3.135 3.021,3.323 0.885,0.188 10 false Connector E 2.26,4.229 3.177,4.438 0.917,0.208 10 false Color: Orange 0.833,3.781 1.229,3.99 0.396,0.208 10 false P2+ 2.135,3.781 2.406,3.99 0.271,0.208 10 false P2-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
z15-1 (P2+) - Body ground Ignition switch ON Below 1 V
z15-2 (P2-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z15-1 (P2+) - z15-2 (P2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z15-1 (P2+) - z15-2 (P2-) Always 1 MΩ or higher
z15-1 (P2+) - Body ground
z15-2 (P2-) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE ASSEMBLY)
4.CHECK CENTER AIRBAG SENSOR
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.
C162203E05
0.272,1.192 1.490,1.538 1.218,0.347 10 Variable Vent Hole Squib 0.85,0.589 0.749,1.159 false 1.949,1.337 2.840,1.678 0.891,0.341 10 Center Airbag Sensor 1.067,0.694 1.251,0.878 0.184,0.184 10 E 0.94,0.694 1.124,0.878 0.184,0.184 10 F 1.621,0.682 1.804,0.866 0.184,0.184 10 C 1.494,0.682 1.678,0.866 0.184,0.184 10 D

Connect the connectors to the front passenger airbag and center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B181A, B181B, B181C or B181D is not output.


HINT:

Codes other than DTC B181A, B181B, B181C and B181D may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE ASSEMBLY)
a.
U153669E02
1.427,0.917 1.521,1.448 false 1.552,0.917 1.427,0.917 false 0.167,0.615 1.042,1.458 false 0.281,0.615 0.167,0.615 false 0.208,0.094 2.052,0.292 1.844,0.198 10 false Variable Vent Hole Squib 0.354,0.521 2.792,0.708 2.438,0.188 10 false No. 2 Instrument Panel Wire Assembly 1.583,0.823 3.052,1.021 1.469,0.198 10 false Instrument Panel Wire 1.979,1.427 2.146,1.594 0.167,0.167 10 false A 1.646,1.635 1.813,1.802 0.167,0.167 10 false B 1.323,1.646 1.49,1.813 0.167,0.167 10 false C 1.125,1.646 1.292,1.813 0.167,0.167 10 false D 0.813,1.656 0.979,1.823 0.167,0.167 10 false E 0.615,1.656 0.781,1.823 0.167,0.167 10 false F 1.479,2.25 2.875,2.438 1.396,0.188 10 false Center Airbag Sensor 0.406,2.719 2.99,3.052 2.583,0.333 10 false Front view of wire harness connector: (to No. 2 Instrument Panel Wire Assembly) 2.375,3.688 3.208,3.917 0.833,0.229 10 false Connector C 0.281,3.781 0.573,3.958 0.292,0.177 10 false Hz2

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire assembly.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Hz2-1 - Body ground Ignition switch ON Below 1 V
Hz2-2 - Body ground



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Hz2-1 - Hz2-2 Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Hz2-1 - Hz2-2 Always 1 MΩ or higher
Hz2-1 - Body ground
Hz2-2 - Body ground




OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE