Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27L0U _58 Vehicle Interior _049342 SEAT _0235877 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

When the seat memory SET switch and a seat memory switch (seat memory switch 1 or seat memory switch 2) are pressed simultaneously, the outer mirror control ECU commands the position control ECU and switch through CAN communication to record each position value.

WIRING DIAGRAM

B188602E02
5.052,3.531 6.792,3.885 1.74,0.354 10 false Front Power Seat Switch LH (Position Control ECU) 2.771,3.479 3,3.656 0.229,0.177 10 false M8 3.042,2.875 3.51,3.042 0.469,0.167 10 false MSWE 3.01,1.448 3.313,1.615 0.302,0.167 10 false MM 3.021,1.927 3.323,2.094 0.302,0.167 10 false M1 3.042,2.406 3.344,2.573 0.302,0.167 10 false M2 1.583,2.875 1.729,3.052 0.146,0.177 10 false E 1.448,1.458 1.792,1.615 0.344,0.156 10 false MRY 1.521,1.938 1.74,2.125 0.219,0.188 10 false M1 1.531,2.406 1.74,2.583 0.208,0.177 10 false M2 1.896,2.771 2,2.938 0.104,0.167 10 false 4 1.906,1.344 2.021,1.49 0.115,0.146 10 false 1 1.896,1.813 2.01,1.969 0.115,0.156 10 false 2 1.896,2.292 2.01,2.458 0.115,0.167 10 false 3 2.729,2.771 2.896,2.927 0.167,0.156 10 false 10 2.781,1.323 2.896,1.49 0.115,0.167 10 false 9 2.781,1.792 2.875,1.958 0.094,0.167 10 false 8 2.771,2.281 2.896,2.448 0.125,0.167 10 false 7 0.563,3.531 0.771,3.729 0.208,0.198 10 false M6 1,5.188 2.677,5.385 1.677,0.198 10 false :CAN Communication Line 0.552,3.688 1.865,3.885 1.313,0.198 10 false Seat Memory Switch 2.76,3.656 4.302,3.844 1.542,0.188 10 false Outer Mirror Control ECU

PROCEDURE

1.CHECK DTC
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

2.CHECK FRONT POWER SEAT CONTROL FUNCTION

B

2.CHECK FRONT POWER SEAT CONTROL FUNCTION
a.

Check that each function of the power seat operates normally by using the front power seat switches.

OK:

Each function of power seat operates normally by using seat switches.




OK

3.CHECK SEAT MEMORY SWITCH FUNCTION

NG

3.CHECK SEAT MEMORY SWITCH FUNCTION
a.

Perform a memory operation properly. Check that the buzzer sounds to indicate the completion of the memory operation.

NOTICE:
·

The seat position will not be recorded if the seat memory SET switch and 2 or more of the seat memory switches (for example, seat memory switch 1 and seat memory switch 2) are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat memory switch function operates normally.




OK

END

NG

4.READ VALUE USING TECHSTREAM (PARK/NEUTRAL POSITION SWITCH)
4.READ VALUE USING TECHSTREAM (PARK/NEUTRAL POSITION SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

According to the display on the Techstream, read the Data List.

ECT
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
Shift SW Status (P Range) PNP switch status / ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
-

OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.


Result
Result Proceed to
OK A
NG (AB60E automatic transmission) B
NG (AB60F automatic transmission) C



A

5.READ VALUE USING TECHSTREAM (SEAT MEMORY SWITCH)

B

GO TO AUTOMATIC TRANSMISSION SYSTEM (PNP SWITCH CIRCUIT)

C

GO TO AUTOMATIC TRANSMISSION SYSTEM (PNP SWITCH CIRCUIT)

5.READ VALUE USING TECHSTREAM (SEAT MEMORY SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

According to the display on the Techstream, read the Data List.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SET Switch Seat memory SET switch signal / ON or OFF ON: Seat memory SET switch on
OFF: Seat memory SET switch off
-
M1 Switch Seat memory switch 1 signal / ON or OFF ON: Seat memory switch 1 on
OFF: Seat memory switch 1 off
-
M2 Switch Seat memory switch 2 signal / ON or OFF ON: Seat memory switch 2 on
OFF: Seat memory switch 2 off
-


OK:

On the Techstream screen, each item changes between ON and OFF according to above chart.



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

6.INSPECT SEAT MEMORY SWITCH
6.INSPECT SEAT MEMORY SWITCH
a.

Remove the seat memory switch (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL).

B443197E01
4.615,2.229 4.896,1.99 true 4.906,2.292 5.052,1.99 true 5.313,2.281 5.177,1.99 true 5.688,2.24 5.323,1.979 true 4.177,0.302 6.615,0.656 2.438,0.354 10 false Component without harness connected: (Seat Memory Switch) 4.448,2.208 4.604,2.406 0.156,0.198 10 false E 4.844,2.313 5.063,2.51 0.219,0.198 10 false M2 5.271,2.302 5.49,2.5 0.219,0.198 10 false M1 5.698,2.271 6.052,2.448 0.354,0.177 10 false MRY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (MRY) - 4 (E) Seat memory SET switch pressed Below 1 Ω
Seat memory SET switch not pressed 10 kΩ or higher
2 (M1) - 4 (E) Seat memory switch 1 pressed Below 1 Ω
Seat memory switch 1 not pressed 10 kΩ or higher
3 (M2) - 4 (E) Seat memory switch 2 pressed Below 1 Ω
Seat memory switch 2 not pressed 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH)

NG

REPLACE SEAT MEMORY SWITCH

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH)
a.
U153220E02
1.417,4 1.135,4.302 false 2.031,4 2.177,4.302 false 1.823,4 1.875,4.302 false 1.625,4 1.542,4.302 false 1.656,1.76 2.115,2.25 false 1.531,1.76 1.688,2.25 false 1.25,1.76 1,2.25 false 1.396,1.75 1.354,2.25 false 0.094,0.073 2.479,0.469 2.385,0.396 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.135,2.656 2.521,3.052 2.385,0.396 10 false Front view of wire harness connector: (to Seat Memory Switch) 0.854,2.271 1.302,2.51 0.448,0.24 10 false M2 1.229,2.271 1.625,2.469 0.396,0.198 10 false M1 1.552,2.271 1.927,2.49 0.375,0.219 10 false MM 1.927,2.271 2.406,2.5 0.479,0.229 10 false MSWE 1.76,4.302 2,4.458 0.24,0.156 10 false M2 1.406,4.302 1.635,4.458 0.229,0.156 10 false M1 0.917,4.302 1.271,4.448 0.354,0.146 10 false MRY 2.125,4.302 2.26,4.469 0.135,0.167 10 false E 1.583,0.896 1.802,1.073 0.219,0.177 10 false M8 0.646,3.792 0.896,3.969 0.25,0.177 10 false M6

Disconnect the M8 ECU connector.


b.

Disconnect the M6 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-7 (M2) - M6-3 (M2) Always Below 1 Ω
M8-7 (M2) - Body ground Always 10 kΩ or higher
M8-8 (M1) - M6-2 (M1) Always Below 1 Ω
M8-8 (M1) - Body ground Always 10 kΩ or higher
M8-9 (MM) - M6-1 (MRY) Always Below 1 Ω
M8-9 (MM) - Body ground Always 10 kΩ or higher
M8-10 (MSWE) - M6-4 (E) Always Below 1 Ω
M8-10 (MSWE) - Body ground Always 10 kΩ or higher




OK

8.CHECK OUTER MIRROR CONTROL ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK OUTER MIRROR CONTROL ECU OPERATION
a.

After replacing the outer mirror control ECU, check that the front power seat control functions operate normally using the front seat switches and seat memory switch.

OK:

Front power seat control functions operate normally.




OK

REPLACE OUTER MIRROR CONTROL ECU

NG

REPLACE FRONT POWER SEAT SWITCH LH