DTC B1793 Occupant Classification Sensor Power Supply Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1793 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the occupant classification sensors.
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (SHORT TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and the 4 occupant classification sensors.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O4-5 (SVC3) - Body ground | Ignition switch ON | Below 1 V |
| O4-6 (SVC4) - Body ground | Ignition switch ON | Below 1 V |
| O4-11 (SVC1) - Body ground | Ignition switch ON | Below 1 V |
| O4-12 (SVC2) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O4-5 (SVC3) - Body ground | Always | 1 MΩ or higher |
| O4-6 (SVC4) - Body ground | Always | 1 MΩ or higher |
| O4-11 (SVC1) - Body ground | Always | 1 MΩ or higher |
| O4-12 (SVC2) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (OPEN) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O4-5 (SVC3) - O7-1 (SVC3) | Always | Below 1 Ω |
| O4-6 (SVC4) - O8- 1 (SVC4) | Always | Below 1 Ω |
| O4-11 (SVC1) - O5-1 (SVC1) | Always | Below 1 Ω |
| O4-12 (SVC2) - O6-1 (SVC2) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| O4-5 (SVC3) - O4-6 (SVC4) | Always | 1 MΩ or higher |
| O4-6 (SVC4) - O4-11 (SVC1) | Always | 1 MΩ or higher |
| O4-11 (SVC1) - O4-12 (SVC2) | Always | 1 MΩ or higher |
| O4-12 (SVC2) - O4-5 (SVC3) | Always | 1 MΩ or higher |
| O4-12 (SVC2) - O4-6 (SVC4) | Always | 1 MΩ or higher |
| O4-11 (SVC1) - O4-5 (SVC3) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK DTC |
Connect the connectors to the occupant classification ECU and the 4 occupant classification sensors.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Using the Techstream, perform "Zero point calibration" (Click here).
|
| ||||
| OK | |
| 10.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform "Sensitivity check" (Click here).
|
| ||||
| OK | |
| 11.CHECK DTC |
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 12.REPLACE FRONT SEAT ASSEMBLY RH |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat assembly RH (Click here for flat type, Click here for manual seat, Click here for power seat).
| NEXT | |
| 13.PERFORM ZERO POINT CALIBRATION |
Connect the negative (-) terminal cable to the battery.
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Using the Techstream, perform "Zero point calibration" (Click here).
| NEXT | |
| 14.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform "Sensitivity check" (Click here).
| NEXT | ||
| ||