Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0210/33    Right Rear Wheel Speed Sensor Signal

DTC    C0215/34    Rear Speed Sensor LH Circuit

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

for Preparation Click here


DESCRIPTION

Refer to DTCs C0200/31, C0205/32, C1235/35 and C1236/36 .

DTC Code
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When any of the following is detected:
  1. At a vehicle speed of 10 km/h (6 mph) or more, an open or short in the sensor signal circuit continues for 1 sec. or more.
  2. Momentary interruption of sensor signal faulty wheel occurs 7 times or more.
  3. Sensor signal circuit is open for 0.5 sec. or more.
  1. Right rear and left rear speed sensor
  2. Each speed sensor circuit
  3. Speed sensor rotor
  4. Sensor installation
C1238/38
C1239/39
When either of the following is detected:
  1. At a vehicle speed of 20 km/h (12 mph) or more, sensor signal of faulty wheel generated noise for 5 sec. or more.
  2. At a vehicle speed of 10 km/h (6 mph) or more, and noise is input once per rotor rotation for 15 sec. or more.
  1. Right rear and left rear speed sensor
  2. Sensor installation

HINT:
  1. DTC C0210/33 and C1238/38 are for the right rear speed sensor.
  2. DTC C0215/34 and C1239/39 are for the left rear speed sensor.


WIRING DIAGRAM


F040100E04


INSPECTION PROCEDURE

1.READ VALUE ON TECHSTREAM (REAR SPEED SENSOR)
  1. Connect Techstream to the DLC3.

  1. Start the engine.

  1. Select the Data List mode on Techstream.

    ABS / VSC / TRAC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    RL Wheel Speed
    Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    RR Wheel Speed
    Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed

  1. Check that there is no difference between the speed value output from the speed sensor displayed by Techstream and the speed value displayed on the speedometer when driving the vehicle.

    OK:
    There is almost no difference in the displayed speed value.

    HINT:
    There is tolerance of +- 10 % in the speedometer indication.



NG
Go to step 3
OK


2.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


  1. INSPECTION USING OSCILLOSCOPE:

    1. Connect the oscilloscope to terminals RR+ - RR- or RL+ - RL- of the skid control ECU.



    2. W004200E19
    3. Drive the vehicle at approximately 19 mph (30 km/h), and check the signal waveform.

      OK:
      A waveform as shown in a figure should be output.

      HINT:
      1. As vehicle speed (wheel revolution speed) in creases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
      2. hen noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter attached to it.

      NOTICE:
      When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
Go to step 6
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

3.INSPECT REAR SPEED SENSOR


  1. 2WD

    1. Disconnect the skid control sensor connector.



    2. F041836E20
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      (A27-1) - (A27-2)
      0.9 to 2.1 kΩ
      RH:
      Tester Connection
      Specified Condition
      (A28-1) - (A28-2)
      0.9 to 2.1 kΩ

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      (A27-1) - Body ground
      10 kΩ or higher
      (A27-2) - Body ground
      10 kΩ or higher
      RH:
      Tester Connection
      Specified Condition
      (A28-1) - Body ground
      10 kΩ or higher
      (A28-2) - Body ground
      10 kΩ or higher

      NOTICE:
      Check the speed sensor signal after replacement (Click here).



  1. 4WD

    1. Remove the seat cushion seatback.

    2. Disconnect the speed sensor connector.



    3. F013045E13
    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      A27-1 (RL+) - A27-2 (RL-)
      0.9 to 1.3 Ω
      RH:
      Tester Connection
      Specified Condition
      A28-1 (RR+) - A28-2 (RR-)
      0.9 to 1.3 Ω

    5. Measure the resistance according to the value(s) in the table below

      Standard resistance:
      LH:
      Tester Connection
      Specified Condition
      A27-1 (RL+) - Body ground
      1 MΩ or higher
      A27-2 (RL-) - Body ground
      1 MΩ or higher
      RH:
      Tester Connection
      Specified Condition
      A28-1 (RR+) - Body ground
      1 MΩ or higher
      A28-2 (RR-) - Body ground
      1 MΩ or higher

      NOTICE:
      Check the speed sensor signal after the replacement. (Click here)



NG
REPLACE REAR SPEED SENSOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR SPEED SENSOR - SKID CONTROL ECU)
  1. Disconnect the skid control ECU connector and the skid control sensor connector.



    C119433E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    S3-20 (RL+) - A27-1 (RL+)
    Below 1 Ω
    S3-6 (RL-) - A27-2 (RL-)
    Below 1 Ω
    RH:
    Tester Connection
    Specified Condition
    S3-5 (RR+) - A28-1 (RR+)
    Below 1 Ω
    S3-19 (RR-) - A28-2 (RR-)
    Below 1 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH:
    Tester Connection
    Specified Condition
    S3-20 (RL+) - Body ground
    10 kΩ or higher
    S3-6 (RL-) - Body ground
    10 kΩ or higher
    RH:
    Tester Connection
    Specified Condition
    S3-5 (RR+) - Body ground
    10 kΩ or higher
    S3-19 (RR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK SPEED SENSOR AND SENSOR ROTOR SERRATIONS


  1. INSPECTION USING OSCILLOSCOPE:

    1. Connect the oscilloscope to terminals RR+ - RR- or RL+ - RL- of the skid control ECU.



    2. W004200E20
    3. Drive the vehicle at approximately 19 mph (30 km/h), and check the signal waveform.

      OK:
      A waveform as shown in a figure should be output.

      HINT:
      1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the fluctuation in the output voltage becomes greater.
      2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to the speed sensor rotor's scratches, looseness or foreign matter attached to it.

      NOTICE:
      When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
Go to step 6
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 

6.CHECK REAR SPEED SENSOR INSTALLATION


  1. 2WD



      F010178E14
    1. Check the sensor installation.

      OK:
      There is no clearance between the sensor and rear axle carrier.



  1. 4WD



      BR03795E46
    1. Check the sensor installation.

      OK:
      There is no clearance between the sensor and rear axle carrier.
      The installation bolt is tightened properly.

Torque:
8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

NOTICE:
Check the speed sensor signal after the replacement (Click here).



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


7.CHECK SPEED SENSOR ROTOR
  1. Remove the rear axle hub and bearing, or rear drive shaft (Click here for 2WD, or Click here for 4WD).



    F042859E02
  1. Check the sensor rotor serrations.

    OK:
    No scratches, missing teeth or foreign objects.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for 2WD)
    B
    NG (for 4WD)
    C

    NOTICE:
    Check the speed sensor signal after the replacement (Click here).



B
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (SPEED SENSOR ROTOR)

C
REPLACE REAR DRIVE SHAFT ASSEMBLY (SPEED SENSOR ROTOR)
A


8.CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here for 2WD or Click here for 4WD).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    1. Check the speed sensor signal after the replacement (Click here).
    2. When replacing the brake actuator assembly, perform zero point calibration (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY