Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2A00    A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

DTC    P2A03    A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)

for Preparation Click here

HINT:
  1. DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
  2. DTC P2A03 indicates malfunctions related to the bank 2 A/F sensor.
  3. Bank 1 refers to the bank that includes cylinder No. 1.
  4. Bank 2 refers to the bank that includes cylinder No. 2.
  5. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P2195 .

DTC No.
DTC Detection Condition
Trouble Area
P2A00
P2A03
Calculated value for air-fuel ratio (A/F) sensor response rate deterioration level is less than threshold
  1. Open or short in A/F sensor circuit
  2. A/F sensor
  3. ECM

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F ratio control is performed for approximately 10 seconds after preconditions are met in order to measure the A/F sensor response rate. During active A/F ratio control, the ECM forcibly increases and decreases the injection volume to a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F ratio control and uses it to calculate the A/F sensor response rate deterioration level.
If the value for A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and sets the DTC.

G034991E07


CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation driving pattern will activate the A/F sensor response monitor.


A079199E49

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to the ON position.
  3. Turn the tester on.
  4. Clear the DTCs (where set).
  5. Select the following menu items: Powertrain / Engine and ECT / Monitor / Result.
  6. Check that RES RATE B1S1 and RES RATE B2S1 is Incomplete.
  7. Start the engine and warm it up (Procedure "A").
  8. Drive the vehicle at between 25 mph and 75 mph (40 km/h and 120 km/h) for 3 minutes. However, the vehicle should be driven at a constant speed (Procedure "B").
  9. Check the monitor result values on the Techstream by selecting the following menu items: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / RES RATE B1S1 and RES RATE B2S1.
  10. If the values indicated on the tester do not change, perform READINESS MONITOR DRIVE PATTERN for the A/F sensor and the heated oxygen sensor (Click here).

    HINT:
    Completion of all A/F sensor monitors is required to change the value in test result.

  11. Note the value of the Monitor Result.
  12. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.
  13. Check if any DTCs (any pending DTCs) are set.

MONITOR STRATEGY


Related DTCs
P2A00: A/F sensor (Bank 1) slow response
P2A03: A/F sensor (Bank 2) slow response
Required Sensors / Components (Main)
A/F sensor
Required Sensors / Components (Related)
Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation
Once per driving cycle
Duration
10 to 15 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P0016, P0018 (VVT system bank 1, 2 - misalignment)
P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment)
P0031, P0032, P0051, P0052 (A/F sensor heater)
P0100, P0102, P0103 (MAF meter)
P0110, P0112, P0113 (IAT sensor)
P0115, P0117, P0118 (ECT sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor)
P0125 (Insufficient ECT for closed loop)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel system)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (CKP sensor)
P0450, P0451, P0452, P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P0505 (Idle speed control)
Active A/F control
Performing
Active A/F control is performed when the following conditions are met
-
Battery voltage
11 V or more
Engine coolant temperature
75°C (167°F) or more
Idle
OFF
Engine RPM
Less than 4000 rpm
A/F sensor status
Activated
Fuel-cut
OFF
Engine load
10 to 70%
Shift position
2 or more
Catalyst monitor
Not yet
MAF
2.5 to 15 g/s

TYPICAL MALFUNCTION THRESHOLDS


Response rate deterioration level
Less than 0.18 V

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Start the engine and turn the tester on.
    3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    4. Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
    6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.

      HINT:
      1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
      2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.


      Standard voltage:

      Tester Display (Sensor)
      Injection Volumes
      Status
      Voltages
      AFS B1S1 or AFS B2S1 (A/F)
      +25%
      Rich
      Less than 3.1
      AFS B1S1 or AFS B2S1 (A/F)
      -12.5%
      Lean
      More than 3.5
      O2S B1S2 or O2S B2S2 (HO2)
      +25%
      Rich
      More than 0.55
      O2S B1S2 or O2S B2S2 (HO2)
      -12.5%
      Lean
      Less than 0.4

      NOTICE:
      The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


      Case
      A/F Sensor (Sensor 1)
      Output Voltage
      HO2 Sensor (Sensor 2)
      Output Voltage
      Main Suspected Trouble Area
      1
      A162605E07
      A162598E02
      -
      2
      A162596E01
      A162598E02
      1. A/F sensor
      2. A/F sensor heater
      3. A/F sensor circuit
      3
      A162605E07
      A162596E01
      1. HO2 sensor
      2. HO2 sensor heater
      3. HO2 sensor circuit
      4
      A162596E01
      A162596E01
      1. Fuel pressure
      2. Gas leakage from exhaust system
        (Air-fuel ratio extremely lean or rich)
    1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
    2. To display the graph, select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS B1 S1 or AFS B2 S1 and O2S B1 S2 or O2S B2 S2 then press the graph button on the Data List view.

      HINT:
      1. DTC P2A00 or P2A03 may be also set when the air-fuel ratio is stuck rich or lean.
      2. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
      3. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
      4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2A00 and/or P2A03
    A
    P2A00 and/or P2A03 and other DTCs
    B

    HINT:
    If any DTCs other than P2A00 or P2A03 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A126269E48
  1. Disconnect the A5 or A6 A/F sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Specified Condition
    HT (1) - +B (2)
    1.8 to 3.4 Ω at 20°C (68°F)
    HT (1) - AF- (4)
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Specified Condition
    HT (1) - +B (2)
    1.8 to 3.4 Ω at 20°C (68°F)
    HT (1) - AF- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2WD model)
    B
    NG (for 4WD model)
    C



B
REPLACE AIR FUEL RATIO SENSOR (Click here)

C
REPLACE AIR FUEL RATIO SENSOR (Click here)
A


3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)


    A136175E10
  1. Disconnect the A5 or A6 A/F sensor connector.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    +B (A5-2) - Body ground
    9 to 14 V
    +B (A6-2) - Body ground
    9 to 14 V

  1. Turn the ignition switch off.

  1. Disconnect the E10 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Specified Condition
    HT (A5-1) - HA1A (E10-2)
    Below 1 Ω
    AF+ (A5-3) - A1A+ (E10-22)
    Below 1 Ω
    AF- (A5-4) - A1A- (E10-30)
    Below 1 Ω
    HT (A6-1) - HA2A (E10-1)
    Below 1 Ω
    AF+ (A6-3) - A2A+ (E10-23)
    Below 1 Ω
    AF- (A6-4) - A2A- (E10-31)
    Below 1 Ω
    Check for short:
    Tester Connection
    Specified Condition
    HT (A5-1) or HA1A (E10-2) - Body ground
    10 kΩ or higher
    AF+ (A5-3) or A1A+ (E10-22) - Body ground
    10 kΩ or higher
    AF- (A5-4) or A1A- (E10-30) - Body ground
    10 kΩ or higher
    HT (A6-1) or HA2A (E10-1) - Body ground
    10 kΩ or higher
    AF+ (A6-3) or A2A+ (E10-23) - Body ground
    10 kΩ or higher
    AF- (A6-4) or A2A- (E10-31) - Body ground
    10 kΩ or higher

  1. Reconnect the ECM connector.



  1. Reconnect the A/F sensor connector.


    A165205E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F SENSOR - ECM)
OK


4.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Read the DTCs using the Techstream.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    P2A00 and/or P2A03
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A


6.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (for 2WD model (Click here) or 4WD model (Click here)).


NEXT


7.PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Read the DTCs using the Techstream.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code / Pending.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P2A00 and/or P2A03
    B



B
REPLACE ECM (Click here)
A

END