Pop up hood lifter assembly.
Danger! Life-threatening injuries!
Before performing any work on the pop up hood lifter, always disconnect the battery earth lead from the battery.
|
Extended Section |
Pop up hood lifter assembly may only be set down with the extended section side facing upwards.
All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.
Replace any damaged part or ones that have been dropped.
For additional information see:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Before performing work on electronic components, disconnect the cable from the negative (-) battery terminal to prevent damage to the electrical system or components.
When disconnecting the cable, turn the START-STOP button (engine switch) and headlight switch off and loosen the cable nut completely. Perform these operations without twisting or prying on the cable. Then disconnect the cable.
Clock settings, radio settings, audio system memory, DTCs and other data will be cleared when the cable is disconnected from the negative (-) battery terminal. Write down any necessary data before disconnecting the cable.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for B48:
Click hereGeneral>MAINTENANCE>B48 BATTERY>REMOVAL
for B58:
Click hereGeneral>MAINTENANCE>B58 BATTERY>REMOVAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
53826A
2.REMOVE UPPER FRONT FENDER PROTECTOR LH
55781E
3.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53470
4.REMOVE POP UP HOOD LIFTER ASSEMBLY
Pop up hood lifter assembly.
Danger! Life-threatening injuries!
Before performing any work on the pop up hood lifter, always disconnect the battery earth lead from the battery.
Pop up hood lifter assembly may only be set down with the extended section side facing upwards.
All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.
Replace any damaged part or ones that have been dropped.
For additional information see:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Check that the START-STOP button (engine switch) off.
Pressing and holding the AUDIO button changes the power source mode to IG OFF.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Detach the clamp (2) and slide the cowl ventilator splash shield (1) in the direction shown by the arrow in the illustration.
Unlock the plug connection (1) and disconnect.
Loosen the T30 bolt (2).
Detach the guide pin (4) to slightly pull the pop up hood lifter assembly (3) forwards in direction of arrow and remove it.
53510
5.REMOVE HOOD LOCK ASSEMBLY
Pyrotechnic components.
Danger! Life-threatening injuries!
All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.
Replace any damaged part or ones that have been dropped.
For additional information see:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Detach the No. 5 water by-pass hose (1) from the radiator reserve tank assembly (2).
Hot surfaces.
Risk of burning!
Perform all work only on components that have cooled down.
Detach the clamps (1).
Detach the cable (2) from the hood lock assembly (1).
Detach the clamp (1).
Loosen the T30 screws (2).
|
Remove in this Direction |
Remove the hood lock assembly (1) in the upward direction.
Disconnect the connectors (2).