Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM3650E _53 Suspension _079981 REAR SUSPENSION _0387959 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Motor vehicle may slip off the vehicle hoist where components are supported.

Danger! Life-threatening injuries!

-

Secure the vehicle hoist against lowering and lifting.


·

Motor vehicle may slip off the vehicle hoist if the weight is distributed unevenly.

Danger! Life-threatening injuries!

-

Ensure there is a specific weight compensation on the motor vehicle.


·

Vehicle may slip off the vehicle hoist if the vehicle hoist is handled incorrectly.

Danger! Life-threatening injuries!

-

Observe safety information on raising the vehicle using a vehicle hoist.




PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 65638 2.REMOVE REAR WHEEL HOUSE LINER LH

HINT:

Use the same procedure as for the RH side.


Hide 65637 3.REMOVE REAR WHEEL HOUSE LINER RH

Hide 48738 4.REMOVE REAR SUSPENSION ARM COVER LH

Hide 48737 5.REMOVE REAR SUSPENSION ARM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 89516P 6.SEPARATE REAR SKID CONTROL SENSOR WIRE LH

a.
C409004

Detach the rear skid control sensor wire LH from the brackets (1).


b.
C413650

Detach the rear skid control sensor wire LH from the brackets (1).


c.

Unlock plug connection (2) and disconnect.


Hide 89516N 7.SEPARATE REAR SKID CONTROL SENSOR WIRE RH

HINT:

Use the same procedure as for the LH side.


Hide 8.SEPARATE REAR FLEXIBLE HOSE LH

a.
C413620

Feed out rear flexible hose LH (1) from the holder (2).


Hide 9.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure as for the LH side.


Hide 10.SEPARATE WIRE HARNESS

a.
C415920

Unlock plug connection (1) and disconnect.


b.

Detach wire harness of the rear height control sensor sub-assembly from the brackets (2) and lay to one side.


Hide 11.REMOVE REAR DISC BRAKE PAD

Hide 37100 12.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 13.REMOVE REAR COIL SPRING LH

Hide 14.REMOVE REAR COIL SPRING RH

HINT:

Use the same procedure as for the LH side.


Hide 48540 15.SEPARATE REAR SHOCK ABSORBER ASSEMBLY LH

a.
C415925C02
1.76,1.375 2.177,1.594 true 1.021,1.958 1.563,1.823 true 2.24,1.51 2.479,1.729 0.24,0.219 10 true *a 0.74,1.865 0.979,2.083 0.24,0.219 10 true *b
*a Wooden Block
*b Jack


Support the rear axle carrier sub-assembly LH with the jack and wooden block.


b.
C409000

Using an 18 mm deep socket wrench, unfasten nut (1).


c.

for Hexagonal Type:

i.

Lift the rear axle carrier sub-assembly LH with the jack and wooden block to the point where the 18 mm bolt (2) can be removed.


ii.

Pull out 18 mm bolt (2).



d.

for Torx Type:

i.

Lift the rear axle carrier sub-assembly LH with the jack and wooden block to the point where the E18 bolt (2) can be removed.


ii.

Pull out E18 bolt (2).



e.

Slowly lower jack until rear axle carrier sub-assembly LH is freely suspended.


f.

Remove the jack and wooden block from under the vehicle.


Hide 48530 16.SEPARATE REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51206A 17.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.

w/ LSD:

i.
C415605

Remove the bolts (1) and rear differential protector (2).


ii.
C415604

Remove the bolt (1) to disconnect the ground wire (2).


iii.
C413541

Unlock and disconnect plug connections (1).


iv.

Loosen the cable clip (2).



b.
C409002

Detach the cable of the parking brake (1) from the holders (2).

HINT:

Perform the operations on the left and right side.



c.
C415912C01
2.833,4.042 3,3.927 false 2.25,3.792 2.448,3.031 true 2.552,3.521 2.719,2.938 true 1.385,4.052 1.656,3.594 true 0.729,4.031 0.865,3.854 true 3.021,3.802 3.24,4 0.219,0.198 10 true *a 1.281,4.063 1.5,4.26 0.219,0.198 10 true *b 0.604,4.052 0.823,4.25 0.219,0.198 10 true *b 2.354,2.802 2.573,3 0.219,0.198 10 true *b 2.646,2.729 2.865,2.927 0.219,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C415913

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.



d.
C413574

Loosen 16 mm bolts (1).


e.

Loosen E18 bolt (2).


f.

Remove rear lower suspension member stopper LH (3).

HINT:

Perform the operations on the left and right side.



g.
C409001

Loosen E18 bolt (1).


h.

Loosen 16 mm bolts (2).


i.

Remove rear suspension member rear lower brace LH (3).

HINT:

Perform the operations on the left and right side.



j.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.