1.REMOVE FASTENER
for Front Bumper Assembly Side:
Remove the fasteners (1) form the front bumper assembly (2).
for Vehicle Body Side:
Remove the fasteners (1).
52114A
2.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET
Remove the screws (1) and front bumper extension mounting bracket (2).
75301A
3.REMOVE FRONT BUMPER EMBLEM SUB-ASSEMBLY
89341K
4.REMOVE FRONT CORNER ULTRASONIC SENSOR
89341L
5.REMOVE FRONT CENTER ULTRASONIC SENSOR
Use the same procedure as for the front corner ultrasonic sensor.
89341M
6.REMOVE FRONT SIDE ULTRASONIC SENSOR
53112E
7.REMOVE LOWER NO. 1 RADIATOR GRILLE
Disconnect the No. 4 engine room wire (1) from the guides (2) on the lower No. 1 radiator grille (3).
Disengage the claws to remove the lower No. 1 radiator grille (3).
53113D
8.REMOVE LOWER RADIATOR GRILLE LH
Disconnect the No. 4 engine room wire (1) from the guides (2) on the lower radiator grille LH (3).
Disengage the claws to remove the lower radiator grille LH (3).
52127C
9.REMOVE FRONT BUMPER HOLE COVER
Disengage the claw (2).
Disengage the hook (3) to remove the front bumper hole cover (1).
53112D
10.REMOVE LOWER RADIATOR GRILLE RH
w/ Toyota Supra Safety:
Disconnect the connector (1).
Disconnect No. 4 engine room wire (1) from the guides (2) on the lower radiator grille RH (3).
Disengage the claws to remove the lower radiator grille RH (3).
53127D
11.REMOVE LOWER SIDE RADIATOR GRILLE RH
Disengage the claws (2) to remove the lower side radiator grille RH (1).
12.REMOVE MILLIMETER WAVE RADAR SENSOR (w/ Toyota Supra Safety)
52536
13.REMOVE FRONT BUMPER SIDE RETAINER LH
Disengage the clamp (1).
Disengage the clamps (2) to disconnect the No. 4 engine room wire (1).
Disengage the welded connections (1).
Remove the clips (1).
Disengage the claws (3).
Feed out and remove the front bumper side retainer LH (2) towards the inside on the guides (4).
52535
14.REMOVE FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
76083B
15.REMOVE FRONT SIDE SPOILER LH
Remove the clips.
Disengage the claws (1) to remove the front side spoiler LH.
76081C
16.REMOVE FRONT SIDE SPOILER RH
Use the same procedure as for the LH side.
76081
17.REMOVE FRONT SPOILER SUB-ASSEMBLY
Remove the 3 T30 bolts.
Disengage the claws (1) to remove the front spoiler sub-assembly.
18.REMOVE NUT
Perform the following procedure only when replacement of a nut.
Using a plier nipper (side cutters), remove the 3 nuts as shown in the illustration.
52829C
19.REMOVE COOL AIR INTAKE GRILLE LH
Disengage the claws (2) to remove the cool air intake grille LH (1).
52829B
20.REMOVE COOL AIR INTAKE GRILLE RH
Use the same procedure as for the LH side.
89348
21.REMOVE NO. 1 ULTRASONIC SENSOR RETAINER
51410
22.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Remove the screws (arrows) and No. 1 engine under cover assembly (1).
53896B
23.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Remove the screws (arrows) and front fender front splash shield LH (1).
53895B
24.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Use the same procedure as for the LH side.
81150
25.REMOVE HEADLIGHT ASSEMBLY LH
81110
26.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
86510D
27.REMOVE HIGH PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>REMOVAL
86510C
28.REMOVE HIGH PITCHED HORN ASSEMBLY (for Dual Type)
Use the same procedure as for the opposite side.
52611
29.REMOVE FRONT BUMPER ENERGY ABSORBER
w/o Pedestrian detection chamber assembly:
Remove the front bumper energy absorber (1).
w/ Pedestrian detection chamber assembly:
Disconnect the connectors (1).
Remove the front bumper energy absorber with pedestrian detection chamber assembly (2).
Remove the pedestrian detection chamber assembly (1) from front bumper energy absorber (2).
53111M
30.REMOVE FRONT BUMPER INNER SUPPORT
Remove the T30 bolts (1), bolts (2) and front bumper inner support (3).
52521B
31.REMOVE FRONT BUMPER UPPER RETAINER
Remove the bolts (1) and front bumper upper retainer (2).
53295A
32.REMOVE RADIATOR UPPER AIR DEFLECTOR
Remove the bolts (1).
Disconnect the hood lock control cable assembly from the guides(1).
Disengage guides (3) to remove the radiator upper air deflector (2).
57161
33.REMOVE FRONT CROSSMEMBER
Remove the T50 bolts (1) and T30 bolts (2).
Remove the bolts (3) and front crossmember (4).
34.REMOVE SUB RADIATOR SUPPORT (for LH Side)
Disengage the clip in the marked area.
Do not disengage the No.3 radiator hose (1) and radiator hose sub-assembly (1).
Remove the T45 bolts (1).
Remove the auxiliary coolant radiator bracket plate LH (2) to separate the sub radiator (1).
Carefully remove the sub radiator support (3) from the body.
35.REMOVE SUB RADIATOR SUPPORT (for RH Side)
Do not disengage the No.1 radiator hose (1) and radiator hose sub-assembly (1).
Remove the T45 bolts (1).
Remove the auxiliary coolant radiator bracket plate RH (2) to separate the sub radiator (1).
Carefully remove the sub radiator support (3) from the body.
36.REMOVE SUB RADIATOR AIR DUCT LH (for B58)
Remove the clips (1) and sub radiator air duct LH (2).
37.REMOVE SUB RADIATOR AIR DUCT RH (for B58)
Use the same procedure as for the LH side.
52144L
38.REMOVE UPPER AUXILIARY COOLANT RADIATOR BRACKET LH
Remove the T45 bolts (1).
Using a deep socket wrench 18 mm, remove the 18 mm bolts (2) and upper auxiliary coolant radiator bracket LH (3).
52143J
39.REMOVE UPPER AUXILIARY COOLANT RADIATOR BRACKET RH
Use the same procedure as for the LH side.
52146J
40.REMOVE LOWER AUXILIARY COOLANT RADIATOR BRACKET LH
Remove the T45 bolts (1) and lower auxiliary coolant radiator bracket LH (2).
52145J
41.REMOVE LOWER AUXILIARY COOLANT RADIATOR BRACKET RH
Use the same procedure as for the LH side.
52131A
42.REMOVE FRONT BUMPER REINFORCEMENT
Remove the T30 bolt (1) to disengage the radiator brace rod sub-assembly (2).
Perform the operations on the left and right side.
Disengage the clamps (3) to disconnect the No. 4 engine room wire (4).
Perform the operations on the left and right side.
Secure radiator assembly (1) on the radiator support (2) and the upper radiator support sub-assembly (3) with suitable auxiliary materials.
Remove the T30 bolt (1) and bottom cooler module mount (2).
Perform the operations on the left and right side.
Loosen bolt (1) with the special tool 2 464 950 a few revolutions.
Guide through the special tool from below, between the radiator assembly (1) and the support for the front bumper.
Perform the operations on the left and right side.
Remove the bolts (1).
Perform the operations on the left and right side.
Remove the front bumper reinforcement (2) toward the front.
52115K
43.REMOVE FRONT BUMPER SIDE SUPPORT
Description is for left component only. Procedure on the right side is identical.
Remove the T30 bolts (1) and front bumper side support (2).
52822
44.REMOVE AIR INTAKE DUCT LH
52821
45.REMOVE AIR INTAKE DUCT RH
46.REMOVE TEMPERATURE SENSOR ASSEMBLY
52811A
47.REMOVE NO. 1 COOL AIR INTAKE DUCT
w/ Airbag Sensor:
Disconnect the connector (1).
Disengage the clamps (2) to disconnect the No. 4 engine room wire (3).
Disengage the clamps (1) to disconnect the No. 4 engine room wire (2).
Disengage the guides (2) to remove the No. 1 cool air intake duct (1).
53016
48.REMOVE RADIATOR BRACE ROD SUB-ASSEMBLY
Remove the radiator brace rod sub-assembly (1) out of the No. 1 cool air intake duct (2).
52126
49.REMOVE FRONT BUMPER RETAINER LH
Disengage the clamp (1) to disconnect the No. 4 engine room wire (2).
Remove the bolts (1) and front bumper retainer LH (2).
52125
50.REMOVE FRONT BUMPER RETAINER RH
Use the same procedure as for the LH side.
51.REMOVE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)
53510
52.REMOVE HOOD LOCK ASSEMBLY
17700
53.REMOVE AIR CLEANER ASSEMBLY
for B48:
Click hereEngine / Hybrid System>B48 (INTAKE / EXHAUST)>AIR CLEANER ASSEMBLY>REMOVAL
for B58:
Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>AIR CLEANER ASSEMBLY>REMOVAL
17312
54.REMOVE INLET NO. 2 AIR DUCT
for B48:
Click hereEngine / Hybrid System>B48 (INTAKE / EXHAUST)>INLET AIR DUCT>REMOVAL
for B58:
Click hereEngine / Hybrid System>B58 (INTAKE / EXHAUST)>INLET AIR DUCT>REMOVAL
89174
55.REMOVE AIRBAG SENSOR (w/ Airbag Sensor)
53212
56.REMOVE RADIATOR SUPPORT LH
Remove the bolts (1) and radiator support LH (2).
53211
57.REMOVE RADIATOR SUPPORT RH
Use the same procedure as for the LH side.
52147J
58.REMOVE LOWER FRONT BUMPER REINFORCEMENT
Remove the E10 bolts (1).
Perform the operations on the left and right side.
Remove the lower front bumper reinforcement (2) to the bottom.
59.REMOVE IMPACT ABSORBER
Drill out the blind rivet.
Remove both impact absorbers (1).
52676
60.REMOVE FRONT BUMPER LOWER SIDE SUPPORT LH
Remove the E8 bolt (1).
Remove the E10 bolts (1) and front bumper lower side support LH (2).
52675
61.REMOVE FRONT BUMPER LOWER SIDE SUPPORT RH
Use the same procedure as for the LH side.