Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY
RM3650E _59 Vehicle Exterior _080029 DOOR / HATCH _0388187 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Working on 12 V vehicle electrical system.

Risk of short circuits! Risk of fire!

-

Disconnect battery earth lead from battery.




NOTICE:

After the engine switch off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.


HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 53826A 2.REMOVE FRONT FENDER UPPER PROTECTOR LH

Hide 55878B 3.REMOVE COWL VENT COVER LH (for LHD)

Hide 55877B 4.REMOVE COWL VENT COVER RH (for RHD)

Hide 5.REMOVE ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)

Hide 53510 6.REMOVE HOOD LOCK ASSEMBLY

a.

w/ Pop Up Hood:

CAUTION:
·
B475753

Airbag unit.

Danger! Life-threatening injuries!

-

All work on pyrotechnic parts may be carried out by technically experienced and appropriately trained personnel only.

-

Replace any damaged part or ones that have been dropped.

-

For additional information see: Safety regulations on handling components with gas generators.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION




i.
B506433

Unclip cable with the holder (1).


ii.

Unlock connector (2) and disconnect.



b.
B506434

Unclip cable with the holder (1).


c.

Loosen T30 screws (2).


d.
B506435

Feed out the hood lock assembly (1) in an upward direction.


e.

Disconnect hood lock control cable assembly linkage (2) and remove the hood lock assembly (1).


Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67914 8.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 9.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 53433 10.REMOVE HOOD SUPPORT BRACKET

a.
B506422

Release diagnostic socket (1) on the retaining clip (2) and pull the hood support bracket (3) down and out.


b.
B506421

Unclip the hood lock control cable assembly (1) on the hood support bracket (2) and disconnect.


c.
B506424

Release the T25 screws (1) and remove the hood support bracket (2).


Hide 53630 11.REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B506431

Disconnect hood lock control cable assembly (1) from the guides (2).


b.
B506429

Unclip hood lock control cable bracket (1) from the body.


c.

Loosen lid (2) on retaining lugs (3) and fold up and to the front.


d.
B506430

Disconnect hood lock control cable assembly (1) from the hood lock control cable bracket (2).


e.
B506436

Remove hood lock control cable assembly (1) together with the hood lock control cable bracket.


f.
B506428

Disconnect the hood lock control cable assembly (1) from the guide (2).


g.
B506437

Remove rubber grommet (1) and work the hood lock control cable assembly (2) out in the direction of the arrow and remove.