52023
1.INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY
Install the replace seals (1).
Set the rear bumper reinforcement sub-assembly (2).
Using a deep socket wrench 18 mm, install the 18 mm nuts (1).
52615
2.INSTALL BUMPER ENERGY ABSORBER
Install the rear bumper energy absorber (2) with clips (1).
Install the screws (1).
Install the screws (1).
Engage the clamps (1) to connect the wiring harness (2).
3.INSTALL NO. 1 REAR BUMPER SUPPORT
Install the No. 1 rear bumper support (2) with nuts (1).
Connect the wiring harness (1) to the holders (2).
Engage the connector (1) to the No. 1 rear bumper support (2).
4.INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY LH
Connect the connector (1) and wiring harness (3).
Engage the clamp (2).
Install the rear bumper side support sub-assembly LH (3) with nuts (2).
Install the screws (1).
Install the T20 screws (1) on the rear bumper side support sub-assembly LH (2).
Install the screws (1) on the rear bumper side support sub-assembly LH (2).
5.INSTALL REAR BUMPER SIDE SUPPORT SUB-ASSEMBLY RH
Set the rear bumper side support sub-assembly RH (3).
Install the nuts (2).
Install the screws (1).
Install the T20 screws (1) on the rear bumper side support sub-assembly RH (2).
Install the screws (1) on the rear bumper side support sub-assembly RH (2).
6.INSTALL TELEVISION ANTENNA ASSEMBLY (w/ Digital terrestrial television)
7.INSTALL BLIND SPOT MONITOR SENSOR LH
8.INSTALL BLIND SPOT MONITOR SENSOR RH
Use the same procedure as for the LH side.
52616B
9.INSTALL ABSORBER FUNNEL LH
52615C
10.INSTALL ABSORBER FUNNEL RH
Use the same procedure as for the LH side.
11.INSTALL AIR INLET TRIM STRIP LH
Install the air inlet trim strip LH (1) and engage the claws (2).
12.INSTALL AIR INLET TRIM STRIP RH
Use the same procedure as for the LH side.
13.INSTALL REAR BUMPER COVER LOWER SECTION
Engage the claws (2) to install the rear bumper cover lower section (1).
Perform the operations on the left and right side.
Install the clips (1).
Engage the clamps (2) to install the wiring harness (1).
14.INSTALL SYMBOL EMBLEM
15.INSTALL NAME PLATE
16.INSTALL NO. 1 REAR NAME PLATE
81920
17.INSTALL REFLEX REFLECTOR ASSEMBLY LH
Engage the claws (1) to install the reflex reflector assembly LH.
Install the screws (1).
81910
18.INSTALL REFLEX REFLECTOR ASSEMBLY RH
Use the same procedure as for the LH side.
19.INSTALL REAR BUMPER PLATE RH
Engage the hook (3).
Engage the claw to install the rear bumper plate RH (1).
81270
20.INSTALL LICENSE PLATE LIGHT ASSEMBLY
21.INSTALL BRACKET FOR REAR VIEW CAMERA
22.INSTALL TELEVISION CAMERA ASSEMBLY
81670A
23.INSTALL BACK-UP LIGHT ASSEMBLY
89348A
24.INSTALL NO. 2 ULTRASONIC SENSOR RETAINER
89342A
25.INSTALL REAR CENTER ULTRASONIC SENSOR
89342B
26.INSTALL REAR SIDE ULTRASONIC SENSOR
89342
27.INSTALL REAR CORNER ULTRASONIC SENSOR
Use the same procedure as for the rear side ultrasonic sensor.
81560
28.INSTALL REAR COMBINATION LIGHT ASSEMBLY LH
81550
29.INSTALL REAR COMBINATION LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
86240
30.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (w/ Stereo Component Amplifier)
64730C
31.INSTALL DECK TRIM SIDE BOARD AND DECK SIDE TRIM COVER RH