Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)
RM3650E _58 Vehicle Interior _080097 SEAT _0388585 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 89952 1.REMOVE OCCUPANT DETECTION ECU (w/ Occupant Detection ECU)

Hide 73240 2.REMOVE FRONT SEAT INNER BELT ASSEMBLY

Hide 71862 3.REMOVE FRONT SEAT CUSHION INNER SHIELD

Hide 71812D 4.REMOVE FRONT SEAT CUSHION SHIELD

a.
B539401

Remove the clip (1).


b.

Detach the claws (3) to separate the front seat cushion shield (2) from outward.


c.
B539402C02
0,0 0,0 false
V100136

Remove in this Direction
V100155

Protective Tape


Pull the bottom of front seat cushion shield (1) outwards slightly.


d.

Detach the guide (2) and guide (3).


e.

Using a screwdriver with its tip wrapped in protective tape, detach the claws (4) to remove the front seat cushion shield (1).


Hide 73706A 5.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET (w/ Bracket)

Hide 6.REMOVE FRONT POWER SEAT SWITCH (for Driver Side)

Hide 84922B 7.REMOVE FRONT POWER SEAT SWITCH (for Front Passenger Side)

Hide 72128B 8.REMOVE FRONT SEAT SUPPORT

a.
B539410C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clamp (1).


b.

Cover the area around the rivet (2).


c.

Drill out the rivet (2).

NOTICE:
·

Do not drill the rivet at an angle as this will cause damage to the drill and rivet installation hole. Line up the drill with the rivet, and carefully drill out the rivet head.

·

Be careful as the drilled rivet will be very hot.




d.

Remove the front seat support forwards.


Hide 73920A 9.REMOVE FRONT SEAT AIRBAG ASSEMBLY

a.
B539409

Disconnect the connector (1) from the connector housing.


b.
B538768

Detach the separate type front seat cushion cover (1).


c.

Detach the clamps (2).


d.
B538769

Detach the separate type front seatback cover (1) in the marked area.


e.
B538770

Using a special tool 0 490 472 (00 5 020), open the fasteners (1) in the marked area.

SST
09300-WA180  


f.
B538771

Detach the separate type front seatback cover (1) in the marked area.


g.
B538772

Loosen the nuts (1).


h.

Fold the separate type front seatback cover with pad (2) to the side.


i.
B538773

Pull the front seat airbag assembly (1) carefully from the separate type front seatback pad (2).


j.

Remove the front seat airbag assembly (1) out carefully from the pocket in the separate type front seatback cover (3).

NOTICE:

Make sure that the stud bolts (4) do not damage the pocket in the separate type front seatback cover.



Hide 10.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.
B539414

Disconnect the connector (1).


b.

Detach the clamps (2).


c.
B539957

Position the separate type front seatback cover with pad (1) as illustrated.

NOTICE:

Handle the separate type front seatback cover with pad (1) carefully to avoid damage.



d.

Remove the separate type front seatback cover with pad (1) from the front seat headrest assembly (2).


Hide 71842 11.REMOVE FRONT SEATBACK GARNISH

Hide 71074S 12.REMOVE SEPARATE TYPE FRONT SEATBACK COVER

Hide 71910A 13.REMOVE FRONT SEAT HEADREST ASSEMBLY

Hide 71579 14.REMOVE FRONT SEATBACK BOARD

Hide 71931 15.REMOVE FRONT SEAT HEADREST SUPPORT

Hide 72760D 16.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

Hide 71183C 17.REMOVE SEATBACK SIDE SUPPORT ADJUSTER ASSEMBLY

Hide 18.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

w/ Occupant Detection ECU:

i.
B546367

Loosen the screw (1).


ii.

Remove the cable (2) from the front seat adjuster assembly (3).



b.
B541052

Disconnect the connector (1).


c.

Detach the clamp (2).


d.
B541053

Using a clip remover, detach the clips (1).


e.

Detach the separate type front seat cushion cover with pad (2) in the marked area.


f.
B542159

Position the separate type front seat cushion cover with pad (1) as illustrated.


g.

Detach the separate type front seat cushion cover with pad (1) in the marked area (2).


Hide 71071S 19.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

Hide 71640S 20.REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

a.
B545983

Disconnect the connector (2).


b.

Detach the clamp (1) to separate the front seat wire.


c.
B539416

Loosen the T50 bolts (1).

HINT:

Use the same procedure for the opposite side.



d.
B543178

Remove the separate type front seatback spring assembly (1).


Hide 21.REMOVE SEAT POSITION AIRBAG SENSOR (w/ Seat Position Airbag Sensor)

a.
B538799C01
0,0 0,0 false
V100136

Remove in this Direction


Remove the connectors in order from (1) to (2) and pull them out of the connector housing (3) one after another in the direction of the arrow.


b.
B538802

Detach the clamp (1).


c.
B538801

Loosen the bolt (1).


d.

Pull the seat position airbag sensor (2) out up of the front seat adjuster assembly (3) upwards and remove.


Hide 22.REMOVE SEAT POSITION SENSOR MAGNET (w/ Seat Position Airbag Sensor)

Hide 23.REMOVE BELT WARNING OCCUPANT DETECTION SENSOR (for Front Passenger Side)

Hide 89710 24.REMOVE POSITION CONTROL ECU ASSEMBLY (for Driver Side)

a.
B542162

Detach the clamps (1) and guide (2) to remove the position control ECU assembly (3).


Hide 87501 25.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (for Front Passenger Side)