Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)
RM3650E _58 Vehicle Interior _080097 SEAT _0388585 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 87501 1.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (for Front Passenger Side)

Hide 89710 2.INSTALL POSITION CONTROL ECU ASSEMBLY (for Driver Side)

a.
B542162

Attach the guide (2) and clamps (1) to install the position control ECU assembly (3).


Hide 3.INSTALL BELT WARNING OCCUPANT DETECTION SENSOR (for Front Passenger Side)

Hide 4.INSTALL SEAT POSITION SENSOR MAGNET (w/ Seat Position Airbag Sensor)

Hide 5.INSTALL SEAT POSITION AIRBAG SENSOR (w/ Seat Position Airbag Sensor)

a.
B538801

Install the seat position airbag sensor (2) to the front seat adjuster assembly (3) from above and position it correctly.


b.

Tighten the bolt (1).

Torque:
1.3 N*m (13 kgf*cm, 12 in.*lbf)


c.
B538802

Attach the clamp (1).


d.
B538804C01
0,0 0,0 false
V100136

Install in this Direction


Install the connectors correctly into the connector housing (3) in the sequence (1) to (2) in the direction of arrow.


Hide 71640S 6.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

a.
B543178

Position the separate type front seatback spring assembly (1) correctly.


b.
B539416

Replace the T50 bolts (1).


c.

Tighten the T50 bolts (1).

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:

Use the same procedure for the opposite side.



d.
B545983

Attach the clamp (1) to connect the front seat wire.


e.

Connect the connector (2).


Hide 71071S 7.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

Hide 8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.
B541052

Attach the clamp (2).


b.

Connect the connecter (1).


c.
B542159

Position the separate type front seat cushion cover with pad (1) as illustrated.


d.

Attach the separate type front seat cushion cover with pad (1) in the marked area (2).


e.
B541053

Attach the separate type front seat cushion cover with pad (2) correctly in the marked area.


f.

Install the clips (1).


g.

w/ Occupant Detection ECU:

i.
B546367

Install the cable (2) to the front seat adjuster assembly (3).


ii.

Tighten the screw (1).

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)



Hide 71183C 9.INSTALL SEATBACK SIDE SUPPORT ADJUSTER ASSEMBLY

Hide 72760D 10.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)

Hide 71931 11.INSTALL FRONT SEAT HEADREST SUPPORT

Hide 71579 12.INSTALL FRONT SEATBACK BOARD

Hide 71910A 13.INSTALL FRONT SEAT HEADREST ASSEMBLY

Hide 71074S 14.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

Hide 71842 15.INSTALL FRONT SEATBACK GARNISH

Hide 16.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.
B542161

Install the separate type front seatback cover with pad (1) correctly over the front seat headrest assembly (2).

NOTICE:

Handle the separate type front seatback cover with pad (1) carefully to prevent damage.



b.

Install the separate type front seatback cover with pad (1) correctly on the backrest width adjustment (3).


c.
B539414

Attach the clamps (2).


d.

Connect the connector (1).


Hide 73920A 17.INSTALL FRONT SEAT AIRBAG ASSEMBLY

a.
B538773

Install the front seat airbag assembly (1) carefully into the pocket of separate type front seatback cover (3).

NOTICE:

Make sure that the stud bolts (4) do not damage the pocket in the separate type front seatback cover.



b.

Position the front seat airbag assembly (1) correctly in the separate type front seatback pad (2).


c.
B538772

Position the separate type front seatback cover with pad (2) correctly.


d.

Replace the nuts (1).


e.

Tighten the nuts (1).

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


f.
B538771

Attach the separate type front seatback cover with pad (1) correctly in the marked area.


g.
B538770

Using a special tool 0 490 472 (00 5 020), close the fasteners (1) in the marked area.

SST
09300-WA180  


h.
B538769

Attach the separate type front seatback cover (1) correctly in the marked area.


i.
B538768

Attach the clamps (2).


j.

Attach the separate type front seat cushion cover (1).


k.
B539409

Connect the connector (1) to the connector housing.


Hide 72128B 18.INSTALL FRONT SEAT SUPPORT

a.
B545987C01
0,0 0,0 false
V113147

Install in this Direction


Install the front seat support (3) backwards.


b.

Replace the rivet (2).


c.

Fasten the front seat support (3) with the rivet (2).

NOTICE:
·
B171664C47
1.479,2.198 1.073,1.656 1.073,1.656 1.51,1.156 true 1.698,0.917 2.51,1.646 2.51,1.646 1.729,2.531 true 0.833,1.573 1.146,1.771 0.313,0.198 10 false *a 2.438,0.635 2.75,0.833 0.313,0.198 10 false *b 2.438,2.417 2.75,2.615 0.313,0.198 10 false *c 2.573,1.552 2.885,1.75 0.313,0.198 10 false *1
*1 Mandrel
*a Riveter
*b Incorrect
*c Correct


Do not pry on the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C45
0.729,0.167 0.896,0.167 false 0.802,2.417 0.969,2.417 false 0.802,1.146 0.969,1.146 false 0.938,0.063 1.25,0.26 0.313,0.198 10 false *a 1,1.031 1.313,1.229 0.313,0.198 10 false *a 1,2.313 1.313,2.51 0.313,0.198 10 false *a 2.573,0.531 2.885,0.729 0.313,0.198 10 false *b 2.594,1.552 2.906,1.75 0.313,0.198 10 false *b 2.594,2.74 2.906,2.938 0.313,0.198 10 false *c
*a Riveter
*b Incorrect
*c Correct


Confirm that the rivet is seated properly against the front seat support.

·

Do not tilt the riveter when installing the front seat support with the rivet.

·

Do not leave any space between the rivet head and front seat support.

·
B172391C44
0.719,2.146 0.906,2.146 false 0.74,0.656 0.927,0.656 false 0.969,0.542 1.313,0.76 0.344,0.219 11 false *a 0.948,2.031 1.292,2.25 0.344,0.219 11 false *a 2.49,1.031 2.833,1.25 0.344,0.219 11 false *b 2.49,2.5 2.833,2.719 0.344,0.219 11 false *c
*a Riveter
*b Incorrect
*c Correct


Do not leave any space between the front seat support and front seat assembly. Firmly hold the front seat support and front seat assembly together while installing the rivet.



HINT:

If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.



d.

Attach the clamp (1).


Hide 19.INSTALL FRONT POWER SEAT SWITCH (for Driver Side)

Hide 20.INSTALL FRONT POWER SEAT SWITCH (for Front Passenger Side)

Hide 73706A 21.INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET (w/ Bracket)

Hide 71812D 22.INSTALL FRONT SEAT CUSHION SHIELD

a.
B539403C01
0,0 0,0 false
V100136

Install in this Direction


Attach the claws in the direction of the arrow.


b.

Attach the guide (2) and guide (3).


c.

Attach the claws to install the front seat cushion shield (1) in the direction of the arrow.


d.

Install the clip (4).


Hide 71862 23.INSTALL FRONT SEAT CUSHION INNER SHIELD

Hide 73240 24.INSTALL FRONT SEAT INNER BELT ASSEMBLY

Hide 89952 25.INSTALL OCCUPANT DETECTION ECU (w/ Occupant Detection ECU)