Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › from 2020.03
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388895 FRONT CRANKSHAFT OIL SEAL A

B58 ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT CRANKSHAFT OIL SEAL

NOTICE:
·

Front crankshaft oil seal damage.

Touching the sealing lip (inner) and applying oil to the front crankshaft oil seal will lead to its destruction.

-

Do not touch the sealing lip (inner) of the front crankshaft oil seal.

-

Do not apply oil to the front crankshaft oil seal.

-

Install the front crankshaft oil seal dry.




a.
A441293

Clean sealing surface (1).


b.
A441289

Clean the special tool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) and coat it with fresh engine oil.

SST
09200-WA080  


c.

Position the special tool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) on the crankshaft and bolt it on.

SST
09200-WA080  


d.
A441290

Replace front crankshaft oil seal (1).


e.

Carefully slide the front crankshaft oil seal (1) straight in a rotational movement onto the special tool 0 496 128 (11 8 801) from the set of special tools 0 496 127 (11 8 800) until the front crankshaft oil seal is positioned flush against the cylinder block sub-assembly.

SST
09200-WA080  


f.
A441291

Position the special tool 0 496 130 (11 8 803) from the set of special tools 0 496 127 (11 8 800) and bolt on hand-tight with the nut.

SST
09200-WA080  


g.

Ensure that the front crankshaft oil seal moves in evenly.


h.
A441292

Bolt in the special tool (sleeve) 0 496 130 (11 8 803) from the set of special tools 0 496 127 (11 8 800) with the tool (1) until the special tool (sleeve)0 496 130 (11 8 803) is flush with the cylinder block sub-assembly.

SST
09200-WA080  


Hide 13470 2.INSTALL CRANKSHAFT PULLEY ASSEMBLY

NOTICE:
·

Make sure to use SST when installing the crankshaft pulley assembly.

·

Performing installation without using SST could result in the crankshaft pulley assembly being off-center, which could damage the crankshaft oil seal.



HINT:

When removing and installing or replacing the crankshaft pulley assembly, the front crankshaft oil seal must be replaced.


a.
A441287

Clean the sealing surface (1) from oil and contamination.


b.

Check if the special tool 0 496 595 (11 6 130) is installed and positioned correctly.

SST
09700-WA040  


c.

Special tool 0 496 595 (11 6 130) not installed.

SST
09700-WA040  


d.

Install special tool 0 496 595 (11 6 130).

SST
09700-WA040  


e.

Apply a small amount of engine oil to the sealing surface of the crankshaft pulley assembly.


f.
A471321

Install SST (2 466 729) to the crankshaft by hand.

SST
09214-WA010  


g.
A471320

Using SST (2 466 729), temporarily install the crankshaft pulley assembly (1).

SST
09214-WA010  


h.
A471319

Temporarily install the E12 bolt (1) by hand.


i.

Remove SST (2 466 729).

SST
09214-WA010  


j.
A441786

Tighten the E12 bolts (arrows).

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


k.

Using SST, tighten the bolts an additional 120°.

SST
09900-WA010  

HINT:
C417459C09
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




l.

Remove special tool 0 496 595 (11 6 130).

SST
09700-WA040  


Hide 28100 3.INSTALL STARTER ASSEMBLY

Hide 51219 4.INSTALL FRONT SUSPENSION MEMBER LOWER PROTECTOR

Hide 5.INSTALL FAN AND GENERATOR V BELT

Hide 17880 7.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL