Home › Engine / Hybrid System › B58 (ENGINE MECHANICAL) › ENGINE ASSEMBLY
RM3650E _51 Engine / Hybrid System _080179 B58 ENGINE MECHANICAL _0388897 ENGINE ASSEMBLY A

B58 ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.REMOVE ENGINE STAND

HINT:

Conduct the following operation with the assistance of a second person.


a.
A445260

Connect both hooks of the special tool 0 490 567 (11 0 020) to the front and back of the engine with the engine hangers.

SST
09200-WA860  

HINT:

The workshop crane, lifting gear and the engine hangers on the engine must all be connected to each other so that the engine hangs straight upon lifting.



b.

Raise the engine slowly.


c.
A445560

Release the bolts (1) and remove the engine stand attachment No. 2.


d.
A441954

Install the No. 1 front engine mounting bracket RH (2).


e.

Tighten the E12 bolts (1).

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 2.INSTALL ENGINE ASSEMBLY

CAUTION:
·

Components connected to the engine joint or cross member.

Danger of injury!

-

Check lifting eyes and engine mounting brackets for damage, e.g. cracks.

-

Attach the component to correctly mounted engine joints or cross members only.

-

Exclusively lift the component, do not move it forwards, backwards or in transverse direction.




a.

Install and lower the engine.


b.

Make sure that the No. 1 front engine mounting brackets rest completely on the front engine mounting insulators.


c.
A513865

Tighten down E14 bolt (1).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:

In order to prevent play, lower the engine completely before screwing the engine mount and engine mounting bracket.



d.
A513866

Tighten down E14 bolt (1).

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

NOTICE:

In order to prevent play, lower the engine completely before screwing the engine mount and engine mounting bracket.



e.
A445260

Release both hooks of the special tool 0 490 567 (11 0 020) at the front and back of the engine from the engine hangers.

SST
09200-WA860  


f.
A441445

Unscrew the bolts (1) of the special tool 2 459 012 .

SST
09200-WA610  


g.

Feed out the special tool 2 459 012 at the cylinder head and remove.

SST
09200-WA610  


Hide 3.CONNECT WATER HOSE

HINT:

Make sure that the connections are locked correctly. The locks must engage audibly.


a.
A441949

Connect and lock No. 6 water by-pass hose (3).


b.

Connect and lock the radiator reserve tank hose (1) and No. 7 water by-pass hose (2).


c.
A441878

Connect and lock the No. 6 radiator hose (1) to the water pump sub-assembly (2).


d.
A441877

Connect and lock the No. 7 water by-pass hose (1) to the water pump sub-assembly (2).


e.
A441948

Feed in and install No. 1 water by-pass hose (1).


f.

Connect and lock No. 1 water by-pass hose (1), heater water hose (2), No. 7 water by-pass hose (3) and No. 5 water by-pass hose (4) in the marked areas.


Hide 88707 4.INSTALL SUCTION PIPE SUB-ASSEMBLY

a.

Replace O-ring.


b.
A446751

Position suction pipe sub-assembly (2).


c.

Tighten the T45 bolts (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 88710 5.INSTALL AIR CONDITIONING TUBE ASSEMBLY

a.

Replace O-ring.


b.
A446750

Position air conditioning tube assembly (2).


c.

Tighten the T45 bolts (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 82261A 6.INSTALL GENERATOR WIRE

a.

Insert and install the generator wire.


b.

Tighten nut.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 7.INSTALL OIL COOLER TUBE

a.
A442317

Position the oil cooler tube in the No. 1 automatic transmission oil cooler tube clamp (2).


b.

Tighten down T25 screw (1).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 35000 8.TEMPORARILY TIGHTEN AUTOMATIC TRANSMISSION ASSEMBLY

Hide 35000 9.FULLY TIGHTEN AUTOMATIC TRANSMISSION ASSEMBLY

Hide 58151 14.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

Hide 58165C 16.INSTALL FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 25051 17.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 28100 18.INSTALL STARTER ASSEMBLY

Hide 16573B 20.CONNECT NO. 3 RADIATOR HOSE

HINT:
A441945

Make sure that the connections are locked correctly. The locks must engage audibly.


a.

Connect and lock the No. 3 radiator hose (1).


Hide 23802B 21.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

Hide 89467A 24.INSTALL WIDE RANGE AIR FUEL RATIO SENSOR

Hide 17880 25.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 16711 27.INSTALL FAN SHROUD

Hide 53826A 28.INSTALL FRONT UPPER FENDER PROTECTOR LH

Hide 53825A 29.INSTALL FRONT UPPER FENDER PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 23827A 30.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A441946

Connect and lock the No. 2 fuel vapor feed hose (1).


b.

Engage the clamp.


Hide 31.CONNECT CONNECTOR TO BRAKE BOOSTER TUBE

a.
A441947

Connect and lock the connector to brake booster tube (1).


Hide 82161 32.INSTALL FLOOR WIRE

a.
A441940

Clip in the floor cable (1) for the voltage supply of the power distribution box in the marked area.


Hide 33.INSTALL ENGINE ROOM ECM BOX

NOTICE:
·

Improper routing of cables and wiring harnesses.

Trapped, crushed or damaged cables may cause short circuits and malfunctions.

-

Route all cables without abrasions, do not trap and crush.




a.
A442174

Feed the engine room ECM box (2) into the guide and install.


b.

Tighten the bolts (1).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Feed the wiring harnesses into the holder at the engine room ECM box.


d.

Engage the 3 clamps


e.

Connect connectors (1) and lock.


f.
A442173

The locks (1) and (2) must engage audibly.


Hide 35.INSTALL WIRE HARNESS CLAMP BRACKET

a.
A441939

Install wire harness clamp bracket (2) for the generator wire.


b.

Tighten the E8 screws (1).

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Clip in the lines in the marked areas.


Hide 36. POSITIVE BATTERY CABLE

a.
A442127

Position the starter wire (3).


b.

Secure clamps (2).


c.

Tighten nut (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.
A442133

Insert and install the generator wire (3).


e.

Secure clamps (2).


f.

Tighten nut (1).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


g.
A441479

Insert and install the cover (2) in the direction of the arrow.

i.

The locks (1) must engage audibly.



Hide 12611 37.INSTALL NO. 1 ENGINE COVER

a.
A441234

Make sure the No. 1 engine cover (1) is correctly positioned on the rear side of the engine.


b.
A441744

Install the No. 1 engine cover (1) from the top and clip it in at the grommets into the marked areas.


Hide 12601B 38.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

NOTICE:
·

Damage to the No. 1 engine cover sub-assembly.

Jerky movements during disassembly and excessive application of force during installation may result in breakage of the No. 1 engine cover sub-assembly.

-

Disassemble or mount the No. 1 engine cover sub-assembly carefully.

-

Disassemble or mount snap-lock couplings of the ball pivots one after the other.

-

Disassemble or mount No. 1 engine cover sub-assembly only at temperatures >20 °C.

Vehicle information / Control unit list / DME / Call up control unit functions / Diagnostic request / Diagnostic request / 117 Ambient temperature

-

Use only distilled water as an auxiliary material during installation, no lubricants.




a.
A441271

Check the rubber mount (1) for correct fit in the No. 1 engine cover sub-assembly.


b.
A445286

Install No. 1 engine cover sub-assembly (1) and fix in the grommets (marks).


Hide 55789B 39.INSTALL NO. 2 COWL TOP VENTILATOR LOUVER PROTECTOR

a.
A442481

Position the No. 2 cowl top ventilator louver protector (1).


b.

Tighten down bolts and nut (2).

Torque:
2.6 N*m (27 kgf*cm, 23 in.*lbf)


Hide 55788A 40.INSTALL COWL TOP VENTILATOR LOUVER PROTECTOR

a.
A442473

Position the cowl top ventilator louver protector (2).


b.

Tighten the bolts (1).

Torque:
2.6 N*m (27 kgf*cm, 23 in.*lbf)


Hide 53681 41.INSTALL UPPER FRONT SUSPENSION CENTER BRACE

a.
A442472

Position upper front suspension center brace (3).


b.

Replace E14 bolts (1) and bolts (2).


c.

Tighten the E14 bolts (1).

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


d.

Using SST, tighten the E14 bolts (1) an additional 90°.

SST
09900-WA010  

HINT:
C417459C09
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




e.

Tighten the bolts (2).

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


f.

Using SST, tighten the bolts (2) an additional 90°.

SST
09900-WA010  

HINT:
C417459C09
2.99,1.271 3.156,1.188 false 2.906,2.094 2.906,1.76 false 0.875,3 1.208,3 false 0.104,0.125 0.417,0.281 0.313,0.156 10 false *a 0.448,0.125 0.76,0.281 0.313,0.156 10 false *b 2.042,0.125 2.354,0.281 0.313,0.156 10 false *c 3.188,1.073 3.427,1.271 0.24,0.198 10 false *d 2.854,2.146 3.167,2.302 0.313,0.156 10 false *b 1.302,2.927 1.615,3.083 0.313,0.156 10 false *c
*a Example
*b Before Tightening
*c After Tightening
*d Magnetic Portion


·

The magnetic portion is used to secure the gauge to the vehicle.

·

After first adjusting the needle of the gauge to 0°, tighten to the specified angle.

·

Perform the work procedure carefully so that the gauge, etc. does not become tilted.




Hide 53383 42.INSTALL HOOD TO COWL TOP SEAL

a.
A446747

Press the hood to cowl top seal (1) into the guide.


b.

Feed the cable into the brackets in the marked area.


c.

Make sure that the hood to cowl top seal (1) and the cable are fitted correctly.


Hide 85010 43.INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

Hide 53450A 44.REMOVE AND INSTALL HOOD SUPPORT ASSEMBLY

a.

Support the hood sub-assembly by hand.


b.
A442485

Remove the special tool 0 493 647 (51 2 170) (3) from the ball pin (2).

SST
09800-WA030  


c.

Pull off the special tool 0 493 647 (51 2 170) (3) from the gas pressure spring (1).

SST
09800-WA030  


d.

Continue to support the hood sub-assembly and repeat the operation on the other side of vehicle.

CAUTION:
·

Shutting hood sub-assembly or tailgate.

Danger of injury!

-

Support hood sub-assembly/tailgate in fully open position with the aid of a suitable device.





e.
A442486

Check the clamp (3) is fitted correctly.


f.

Connect ball socket (1) to ball pin (2).


g.

Continue to support the hood sub-assembly and repeat the operation on the other side of vehicle.


Hide 12180E 46.INSTALL OIL FILLER CAP ASSEMBLY

Hide 47. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 49.ADD ENGINE COOLANT (for High Pressure)

Hide 50.ADD ENGINE COOLANT (for Low Pressure)

Hide 53.ADJUST AUTOMATIC TRANSMISSION FLUID LEVEL

Hide 51219 54.INSTALL FRONT SUSPENSION MEMBER LOWER PROTECTOR