Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0057    Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)

DTC    P0058    Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)

DTC    P0141    Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

DTC    P0161    Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)

DTC    P102D    O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON

DTC    P105D    O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P0136 .

HINT:
When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.


A256047E04


DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
Heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
  1. Open in heated oxygen sensor (bank 1, 2 sensor 2) heater circuit
  2. Heated oxygen sensor (bank 1, 2 sensor 2) heater
  3. EFI relay
  4. ECM
P0038
P0058
Heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
  1. Short in heated oxygen sensor (bank 1, 2 sensor 2) heater circuit
  2. Heated oxygen sensor (bank 1, 2 sensor 2) heater
  3. EFI relay
  4. ECM
P0141
P0161
Cumulative heater resistance correction value exceeds the acceptable threshold.
(2 trip detection logic)
  1. Open or short in heated oxygen sensor (bank 1, 2 sensor 2) heater circuit
  2. Heated oxygen sensor (bank 1, 2 sensor 2) heater
  3. EFI relay
  4. ECM
P102D
P105D
The heater current is higher than the specified value while the heater is not operating
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The sensing position of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated oxygen sensor heater range check (P0037, P0038, P0057, P0058, P102D and P105D
    The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.
    If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
  1. Heated oxygen sensor heater performance (P0141 and P0161):
    After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater. If the resistance is above the threshold value, the ECM will determine that there is a malfunction in the heated oxygen sensor heater and stores P0141 and P0161.

MONITOR STRATEGY


Related DTCs
P0037: Heated oxygen sensor (bank 1 sensor 2) heater open/short (Low electrical current)
P0038: Heated oxygen sensor (bank 1 sensor 2) heater open/short (High electrical current)
P0057: Heated oxygen sensor (bank 2 sensor 2) heater open/short (Low electrical current)
P0058: Heated oxygen sensor (bank 2 sensor 2) heater open/short (High electrical current)
P0141: Heated oxygen sensor (bank 1 sensor 2) heater performance
P0161: Heated oxygen sensor (bank 2 sensor 2) heater performance
P102D: Heated oxygen sensor (bank 1 Sensor 2)heater stuck ON
P105D: Heated oxygen sensor (bank 2 Sensor 2) heater stuck ON
Required Sensors/ Components (Main)
Heated oxygen sensor (bank 1, 2 sensor 2) heater
Required Sensors/ Components (Related)
-
Frequency of Operation
Continuous: P0037, P0038, P0057, P0058, P102D, P105D
Once per driving cycle: P0141, P0161
Duration
2.064 seconds: P0038, P0058
0.5 seconds: P0037, P0057, P102D, P105D
10 seconds: P0141 and P0161
MIL Operation
Immediate: P0037, P0038, P0057, P0058, P102D, P105D
2 driving cycles: P0141, P0161
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever the following DTCs are not stored
None

P0037 and P0057 (Case 1) 
All of the following conditions are met
-
Engine
Running
Starter
Off
Catalyst active air fuel ratio control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Learned heater off current operation
Succeeded
Heated oxygen sensor heater high current fail (P0038, P0058)
Not detected
Heater on current - Learned heater off current
0.15 A or less
Heater output
On

P0037 and P0057 (Case 2) 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active air fuel ratio control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Heater off current
Higher than 3.5 A
Hybrid IC high current limiter monitor input
Fail
Heated oxygen sensor heater high current fail (P0038 P0058)
Not detected

P0038 and P0058 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active air fuel ratio control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed

P0141 and P0161 
All of the following conditions are met
-
Heated oxygen sensor heater circuit fail (P0037, P0038, P0057, P0058, P102D and P105D)
Not detected
Battery voltage
10.5 V or higher
Fuel cut
Off
Time after fuel cut on to off
30 seconds or more
Accumulated heater on time
100 seconds or more
Learned heater off current operation
Completed
Duration that rear heated oxygen sensor impedance is less than 15 kΩ
2 seconds or more

P102D and P105D 
All of the following conditions are met
-
Battery voltage
10.5 V or higher
Engine
Running
Starter
Off
Catalyst active air fuel ratio control
Not operating
Time after heater on
10 seconds or more
Learned heater off current operation
Completed
Oxygen sensor heater low current fail (P0037, P0057)
Not detected
Oxygen sensor heater high current fail (P0038, P0058)
Not detected

TYPICAL MALFUNCTION THRESHOLDS


P0037 and P0057 (Case 1) 
Heater current - Learned heater off current
0.3 A or less

P0037 and P0057 (Case 2) 
Heater on current
1 A or less

P0038 and P0058 
Both of the following conditions are met
-
Hybrid IC high current limiter monitor input
Fail
Heater output
On

P0141 and P0161 
Heater resistance
Varies with sensor element temperature (Example: Higher than 23 Ω)

P102D and P105D 
Heater on current
Higher than 1 A

COMPONENT OPERATING RANGE


Heated Oxygen sensor heater current
0.4 to 1 A (when engine idles, heated oxygen sensor warmed up and battery voltage 11 to 14 V)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A198819E19

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0037, P0038, P0057, P0058, P0141, P0161, P102D or P105D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0136 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. When the values for the Data List items O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2 are not 0 A, the heater is on.
  6. Refer to Data List / Active Test [O2 Heater B1S2, O2 Heater B2S2, O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2] (Click here).
  7. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
  8. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
A232485E01
  1. Disconnect the heated oxygen sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H3-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    H4-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)
    *b
    Bank 1
    *c
    Bank 2



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    H3-1 (HT1B) - E12-12 (HT1B)
    Always
    Below 1 Ω
    H4-1 (HT2B) - E12-13 (HT2B)
    Always
    Below 1 Ω
    H3-1 (HT1B) or E12-12 (HT1B) - Body ground
    Always
    10 kΩ or higher
    H4-1 (HT2B) or E12-13 (HT2B) - Body ground
    Always
    10 kΩ or higher



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038, P0057, P0058, P0141, P0161, P102D OR P105D)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0037, P0038, P0057, P0058, P0141, P0161, P102D or P105D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT EFI RELAY
  1. Inspect the EFI relay (Click here).



NG
REPLACE EFI RELAY
OK


6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI RELAY)
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the EFI relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    H3-2 (+B) - 3 (EFI relay holder)
    Always
    Below 1 Ω
    H4-2 (+B) - 3 (EFI relay holder)
    Always
    Below 1 Ω
    H3-2 (+B) or 3 (EFI relay holder) - Body ground
    Always
    10 kΩ or higher
    H4-2 (+B) or 3 (EFI relay holder) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)