Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

for Preparation Click here


DESCRIPTION

  1. When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores the DTC.

    DTC No.
    DTC Detection Condition
    Trouble Area
    P0300
    Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
    1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks).
    2. An emission deterioration misfire occurs (MIL illuminates).
    1. Open or short in engine wire harness
    2. Connector connection
    3. Vacuum hose connections
    4. Ignition system
    5. Fuel injector assembly
    6. Fuel pressure
    7. Mass air flow meter
    8. Engine coolant temperature sensor
    9. Compression pressure
    10. Valve clearance
    11. Valve timing
    12. PCV valve and hose
    13. PCV hose connections
    14. Intake system
    15. ECM
    16. Wire harness or connector
    P0301
    P0302
    P0303
    P0304
    Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
    1. A misfire occurs that may damage the three-way catalytic converter (MIL blinks).
    2. An emission deterioration misfire occurs (MIL illuminates).
    When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores the DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. After the first 1000 crankshaft revolutions, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs 4 times in sequential crankshaft revolutions.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause the three-way catalytic converter damage, is detected (2 trip detection logic).
  1. In every 200 crankshaft revolutions at a high engine rpm, the threshold misfiring percentage is recorded once.
  2. In every 200 crankshaft revolutions at a normal engine rpm, the threshold misfiring percentage is recorded 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple Cylinder Misfire
P0301: Cylinder 1 Misfire
P0302: Cylinder 2 Misfire
P0303: Cylinder 3 Misfire
P0304: Cylinder 4 Misfire
Required Sensors/Components (Main)
Fuel injector assembly
Ignition coil assembly
Spark plug
Required Sensors/Components (Related)
Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Intake air temperature sensor
Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: Emission related misfire
MIL flashes immediately: Catalyst damaged misfire
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not present
P0016 (VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Meter)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop Fuel Control)
P0327, P0328 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0354 (Ignitor)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine rpm
400 to 5800 rpm
Fuel-cut
OFF
Either of following conditions 1 or 2 met
-
1. Engine coolant temperature at engine start
More than -7°C (19°F)
2. Engine coolant temperature
More than 20°C (68°F)

Monitor Period of Emissions-related Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaged-Misfire (MIL Blinks) 
All of following conditions 1, 2, 3 and 4 set
Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately)
Crankshaft 200 revolutions
1. Driving cycle
1st
2. Check mode
OFF
3. Engine RPM
Less than 2200 rpm
4. Intake air amount per revolution
Less than 1.2 g/rev

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-related-misfire: 
Misfire rate
1.538% or more

Monitor Period of Catalyst-damaged-misfire (MIL blinks): 
Number of misfire per 200 revolutions
113 or more (varies with intake air amount and engine RPM)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A236387E02


A237274E02


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to #4) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.


    Engine RPM
    Duration
    Idling
    7.0 minutes or more
    1000
    4.0 minutes or more
    2000
    2.0 minutes or more
    3000
    1.5 minutes or more
  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 30 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Check the "Fuel Cut Elps Time" value in the Data List or the freeze frame data which were present when the malfunction occurred. If the value is more than 0 seconds, a high engine speed (8000 rpm or more) has occurred in the past. Since the misfire may be caused by valve rocker arm detaching due to an extremely high engine speed, check that the valve rocker arms are properly attached (Click here).
  2. By clearing the DTC, "Fuel Cut Elps Time" will be cleared.
  3. If any DTCs other than the misfire DTCs are output, troubleshoot those DTCs first.
  4. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  5. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  6. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel tank is low.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
    4. The problem is complex.
  7. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to #4).
  8. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern, after repairs.
  9. In the event of DTC P0300 being present, perform the following operations:
    1. Clear DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream or scan tool.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  10. When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or more).
  11. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
  12. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs detection.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303 and/or P0304 are output
    A
    DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTION
  1. Check the PCV hose connections.

    OK:
    PCV valve and hose are correctly connected and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.READ DATA LIST (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load (engine load) values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result 
    Data List
    Techstream Display
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT CAT OT F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.

  1. Start the engine allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform steps (d) and (e) and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Of Techstream (Misfire RPM and Misfire Load)" procedures above.

  1. Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the Techstream.
    Result 
    Result
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 18
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


8.CHECK FOR SPARK AND IGNITION (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.



NG
Go to step 34
OK


9.CHECK CYLINDER COMPRESSION PRESSURE ON MISFIRING CYLINDER
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR)


    A167963E28
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F6-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F8-1 - Body ground
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)


    A192902E02
  1. Disconnect the ECM connector.

  1. Disconnect the fuel injector assembly connectors.

  1. Measure the resistance.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    F5-2 - E5-6 (#10)
    Always
    Below 1 Ω
    F6-2 - E5-5 (#20)
    Always
    Below 1 Ω
    F7-2 - E5-2 (#30)
    Always
    Below 1 Ω
    F8-2 - E5-1 (#40)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    F5-2 or E5-6 (#10) - Body ground
    Always
    10 kΩ or higher
    F6-2 - E5-5 (#20) - Body ground
    Always
    10 kΩ or higher
    F7-2 or E5-2 (#30) - Body ground
    Always
    10 kΩ or higher
    F8-2 or E5-1 (#40) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK FUEL INJECTOR ASSEMBLY (FUEL INJECTOR OF MISFIRING CYLINDER)
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 36
OK


15.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


16.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 8.0 gm/sec. and 14.7 gm/sec.



NG
Go to step 29
OK


17.CHECK VALVE TIMING


    G038285E03
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned as shown in the illustration.

    OK:
    Timing marks on the camshaft timing gears are aligned as shown in illustration.

    Text in Illustration 
    *a
    Timing Mark



OK
Go to step 29

NG
ADJUST VALVE TIMING (Click here)

18.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks.

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


19.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 36
OK


20.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK


21.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 2500 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N
    A/C: Off
    Engine Speed: 2500 rpm
    Between 8.0 gm/sec. and 14.7 gm/sec.



NG
Go to step 29
OK


22.CHECK VALVE TIMING


    G038285E03
  1. Remove the cylinder head cover .

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned as shown in the illustration.

    OK:
    Timing marks on the camshaft timing gears are aligned as shown in illustration.

    Text in Illustration 
    *a
    Timing Mark



NG
ADJUST VALVE TIMING
OK


23.INSPECT SPARK PLUG (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG
OK


24.CHECK FOR SPARK AND IGNITION (SPARK TEST)
  1. Perform a spark test .



NG
Go to step 34
OK


25.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


26.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)


    A167963E28
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F6-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    F8-1 - Body ground
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


27.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)


    A192902E02
  1. Disconnect the ECM connector.

  1. Disconnect the fuel injector assembly connectors.

  1. Measure the resistance.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    F5-2 - E5-6 (#10)
    Always
    Below 1 Ω
    F6-2 - E5-5 (#20)
    Always
    Below 1 Ω
    F7-2 - E5-2 (#30)
    Always
    Below 1 Ω
    F8-2 - E5-1 (#40)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    F5-2 or E5-6 (#10) - Body ground
    Always
    10 kΩ or higher
    F6-2 - E5-5 (#20) - Body ground
    Always
    10 kΩ or higher
    F7-2 or E5-2 (#30) - Body ground
    Always
    10 kΩ or higher
    F8-2 or E5-1 (#40) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


28.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


30.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL (P0300, P0301, P0302, P0303 or P0304 output)
    A
    NORMAL (No DTC output)
    B



B
END
A


31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    M1-3 (VG) - E5-28 (VG)
    Always
    Below 1 Ω
    M1-2 (E2G) - E5-30 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    M1-3 (VG) or E5-28 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


32.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter.

    HINT:
    If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303 or P0304.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL (No DTC output)
    A
    ABNORMAL (P0300, P0301, P0302, P0303 or P0304 output)
    B



B
REPLACE ECM (Click here)
A

END 

34.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 35
OK

REPLACE SPARK PLUG 

35.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the ignition coil to an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY 

36.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)