Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E07
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in three-way catalytic converter (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector assembly
  6. Fuel pressure
  7. Mass air flow meter sub-assembly
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Intake system
  14. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in three-way catalytic converter (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
When DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause the three-way catalytic converter damage, is detected (2 trip detection logic).
  1. At a high engine speed, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine speed, a catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.

  1. Misfire Monitor for Mexico Models
    The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
    1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 332 misfires per 1000 crankshaft revolutions) occurs once.
    2. An excessive misfiring rate (approximately 166 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
    The ECM flashes the MIL and stores a DTC when the following condition, which could cause the three-way catalytic converter damage, is detected (2 trip detection logic).
    1. A catalyst damage misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature
Intake air temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: (MIL illuminates when misfire detected)
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333 (Knock control sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine speed
400 to 5400 rpm (Automatic transmission)
450 to 5400 rpm (Manual transmission)
Either of following conditions (a) or (b) met
-
(a) Engine coolant temperature at engine start
More than -7°C (19°F)
(b) Engine coolant temperature
More than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL blinks) 
All of the following conditions 1, 2, 3 and 4 are met
Crankshaft 200 revolutions x 3
Except above (MIL blinks immediately)
Crankshaft 200 revolutions
1. Driving cycles
1st
2. Check mode
OFF
3. Engine speed
Less than 2800 rpm
4. Intake air amount per revolution
Less than 2 g/rev
  1. FOR MEXICO MODELS

Misfire: for Mexico Models 
Monitor runs whenever following DTCs not stored
P0102 - P0103 (Mass Air Flow Meter)
P0110 - P0113 (Intake Air Temperature Sensor)
P0115 - P0118 (Engine Coolant Temperature Sensor)
P0120 - P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop)
P0327, P0328 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (VVT sensor)
P0500 (Vehicle Speed Sensor)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine speed
400 to 5400 rpm
Engine coolant temperature
More than 65°C (149°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire: for Mexico Models 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks): for Mexico Models 
All of following conditions 1 and 2 met
Crankshaft 200 revolutions
1. Driving cycles
1st
2. Check mode
OFF
Except above
Crankshaft 200 revolutions x 3

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-Related-Misfire 
Misfire rate
1.5% or more

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
Number of misfire per 200 revolutions
77 or more (varies with intake air amount and rpm)
  1. FOR MEXICO MODELS

Monitor Period of Emission-Related-Misfire: for Mexico Models 
Misfire rate
33.2% or more: for 1st 1000 revolutions
16.6% or more: after 1st 1000 revolutions

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks): for Mexico Models 
Number of misfire per 200 revolutions
77 or more (varies with intake air amount and rpm)
Paired cylinder misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the Clear DTC procedure).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #6 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

    HINT:
    1. In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

    Engine speed
    Duration
    Idling
    7.0 minutes or more
    1000
    4.0 minutes or more
    2000
    2.0 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 30 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the Clear DTC procedure).

WIRING DIAGRAM


A193219E07


A240481E04


A226216E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
    1. There was insufficient fuel volume in the tank.
    2. Improper fuel is used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders ( [Cylinder #1 Misfire Count to Cylinder #6 Misfire Count]).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not stored the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P0300 is stored
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-15%, the air-fuel ratio may be Rich (-15% or less) or Lean (+15% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire has occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 are output
    A
    DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.

    Result 
    Data List
    Techstream Display
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT CAT OT F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count, #4 Misfire Count, #5 Misfire Count and Cylinder #6 Misfire Count.

  1. Start the engine and allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #6 Misfire Count displayed on the Techstream.
    If no misfire counts occur in any cylinders, perform steps (d) and (e) and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above.

  1. Read the Cylinder #1 Misfire Count to Cylinder #6 Misfire Count or DTCs displayed on the Techstream.


Result 
Result
Proceed to
Most misfires occur in only 1 or 2 cylinders
A
3 cylinders or more have equal misfire counts
B

HINT:
  1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
  2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
  3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 17
A


7.INSPECT SPARK PLUG
  1. Remove the ignition coil assembly and the spark plug from the misfiring cylinder.

  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION (SPARK TEST)
  1. Disconnect the fuel injector assembly connector to prevent the engine from starting.

    CAUTION:
    Always disconnect all the fuel injector connectors.

  1. Remove the ignition coil from the cylinder head.

  1. Perform a spark test (Click here).



NG
Go to step 32
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK ECM TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND /OR #60)
A193171E30
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E12-6 (#10) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-1 (#20) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-7 (#30) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-2 (#40) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-8 (#50) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-3 (#60) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak.

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 34
OK


14.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Read MAF with the engine speed at 2000 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N (Neutral)
    A/C: Off
    Engine Speed: 2000 rpm
    Between 13.1 gm/sec. and 18.9 gm/sec



NG
Go to step 27
OK


16.CHECK VALVE TIMING
  1. Remove the cylinder head cover (Click here and Click here).



    A237949E01
  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) to align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Bank 1
    *b
    Bank 2
    *c
    Timing Mark



OK
Go to step 27

NG
ADJUST VALVE TIMING

17.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks

    OK:
    No leaks from intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


18.CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 34
OK


19.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    Coolant Temp
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


20.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.

  1. Read MAF with the engine speed at 2000 rpm.

    Standard:

    Techstream Display
    Condition
    Specified Condition
    MAF
    Shift lever position: N (Neutral)
    A/C: Off
    Engine Speed: 2000 rpm
    Between 13.1 gm/sec. and 18.9 gm/sec



NG
Go to step 27
OK


21.CHECK VALVE TIMING
  1. Remove the cylinder head cover (Click here and Click here).



    A237949E01
  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) to align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

    Text in Illustration 
    *a
    Bank 1
    *b
    Bank 2
    *c
    Timing Mark



NG
ADJUST VALVE TIMING
OK


22.INSPECT SPARK PLUG
  1. Remove the ignition coil assembly and the spark plug from the misfiring cylinder.

  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


23.CHECK FOR SPARKS AND IGNITION (SPARK TEST)
  1. Disconnect the fuel injector assembly connector to prevent the engine from starting.

    CAUTION:
    Always disconnect all the fuel injector connectors.

  1. Remove the ignition coil assembly from the cylinder head.

  1. Perform a spark test .



NG
Go to step 32
OK


24.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


25.INSPECT ECM TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND /OR #60)
A193171E30
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E12-6 (#10) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-1 (#20) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-7 (#30) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-2 (#40) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-8 (#50) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V
    E12-3 (#60) - E12-14 (E01)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


28.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, 0304, P0305 or P0306.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    ABNORMAL (P0300, P0301, P0302, P0303, 0304, P0305 or P0306 is output)
    A
    NORMAL (DTC is not output)
    B



B
END
A


29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    M1-3 (VG) - E10-14 (VG)
    Always
    Below 1 Ω
    M1-2 (E2G) - E10-13 (E2G)
    Always
    Below 1 Ω
    M1-3 (VG) or E10-14 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


30.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.


NEXT


31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, 0304, P0305 or P0306.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL
    (DTC is not output)
    A
    ABNORMAL
    (P0300, P0301, P0302, P0303, 0304, P0305 or P0306 is output)
    B



B
REPLACE ECM (Click here)
A

END 

32.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test (Click here).

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil assembly and connect the ignition coil assembly connector.

    2. Disconnect the fuel injector assembly connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 33
OK

REPLACE SPARK PLUG (Click here)  

33.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the ignition coil assembly to an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil assembly and connect the ignition coil connector.

    2. Disconnect the fuel injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

34.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP (Click here)