Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2440    Secondary Air Injection System Switching Valve Stuck Open Bank1

DTC    P2441    Secondary Air Injection System Switching Valve Stuck Close Bank1

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2440
Air pressure sensor detects pulsation of exhaust gas despite ECM commanding air switching valve to close, while engine running (2 trip detection logic)
  1. Air switching valve assembly
  2. Open or short in air switching valve circuit
  3. Air pressure sensor
  4. Air pressure sensor circuit
  5. Air injection control driver
  6. ECM
P2441
Air pressure sensor detects no pulsation of exhaust gas despite ECM commanding air switching valve to open, while engine running (2 trip detection logic)
  1. Air switching valve assembly
  2. Open or short in air switching valve circuit
  3. Vacuum hose (air switching valve - air pressure sensor)
  4. Air injection hose
  5. Air pressure sensor
  6. Air pressure sensor circuit
  7. Air injection control driver
  8. ECM

HINT:
Air switching valve normal operation:
When the air switching valve assembly is open, exhaust gas pulsation occurs in the secondary air passage.
When the air switching valve assembly is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

Air switching valve assembly of the secondary air injection system.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
  1. Exhaust gas pulsation is detected by the air pressure sensor despite the ECM commanding the air switching valve assembly to close.
  2. Exhaust gas pulsation is not detected by the air pressure sensor despite the ECM commanding the air switching valve assembly to open.

MONITOR STRATEGY


Related DTCs
P2440: Air Control Valve Stuck Open
P2441: Air Control Valve Stuck Closed
Required Sensors/Components (Main)
Air pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
7 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs not present
P0010 (VVT Oil Control Valve)
P0011 (VVT System - Advance)
P0012 (VVT System - Retard)
P0016 (VVT System - Misalignment)
P0031, P0032 (Air Fuel Ratio Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P014C, P014D, P015A, P015B, P2195, P2196, P2237, P2238, P2239, P2252, P2253 (Air Fuel Ratio Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0171, P0172 (Fuel System)
P0301 - P0304 (Misfire)
P0327, P0328 (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0351 - P0354 (Igniter)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P106B (EVAP Emission Control System Pressure Sensor - Air Injection System Pressure Sensor Correlation)
P2431, P2432, P2433 (Secondary Air Injection System)

Secondary Air Injection ON: 
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (337.5 mmHg) or more
Pressure pattern check during secondary air injection ON*1
Completed
Pressure pattern check during secondary air injection OFF*2
Completed
Air injection control driver failure (open/short or out of range)
Not detected
Secondary air injection system pressure sensor failure (open/short or out of range)
Not detected

*1: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
6 seconds or more
Air pump
ON
Air switching valve
Open
Engine speed
Less than 3750 rpm
Time after engine start
1 second or more

*2: Pressure pattern check during secondary air injection ON
-
Time after secondary air injection starts operation
10 seconds or more
Air pump
OFF
Engine speed
Less than 3750 rpm
Secondary air injection monitor during secondary air injection ON
Completed

Air Switching Valve is Stuck Open: 
Air injection pump
OFF
Engine speed
3750 rpm or less
Secondary air injection pressure sensor (open/short of out of range)
Not detected
Time after secondary air injection system in operation
10 seconds or more
Air switching valve open stuck (P2440, P2442)
ON
Secondary air injection pressure sensor open stuck (P2445)
Not detected
Engine load
7% or more

TYPICAL MALFUNCTION THRESHOLDS


Secondary Air Injection ON (Condition 1): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection ON (Condition 2): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection ON (Condition 3): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 9 kPa (337.5 mmHg)
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection ON (Condition 4): 
Both conditions are met during secondary air injection ON
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection OFF (Condition 1): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection OFF (Condition 2): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
11.25 kPa (84.381 mmHg) or higher
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

Secondary Air Injection OFF (Condition 3): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
2.5 kPa (18.751 mmHg) or higher

Secondary Air Injection OFF (Condition 4): 
Both conditions are met during secondary air injection OFF
-
Cumulative pressure pulsation
Below 9 kPa (67.505 mmHg)
Secondary air injection pressure
Below 2.5 kPa (18.751 mmHg)

P2440 Air Switching Valve is Stuck Open 
One of following conditions is met
(a) or (b) or (c)
(a) Condition 2 (secondary air injection ON) and Condition 2 (secondary air injection OFF)
-
(b) Condition 1 (secondary air injection ON) and no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(c) Condition 1 (secondary air injection ON) and Condition 2 (secondary air injection OFF) and no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-

P2441 Air Switching Valve is Stuck Closed 
1. One of following conditions is met
(a) or (b) or (c) or (d)
(a) Condition 3 (secondary air injection ON)
-
(b) Condition 1 (secondary air injection ON) and Condition 3 (secondary air injection OFF) and no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(c) Condition 1 (secondary air injection ON) and Condition 4 (secondary air injection OFF) and no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF
-
(d) Condition 4 (secondary air injection ON)
-

HINT:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).


MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Check for pending DTCs.

    OK:
    No pending DTC is output.

  14. After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2440 or P2441.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

WIRING DIAGRAM

  1. Refer to P0412 .
  2. Refer to P2431 .

INSPECTION PROCEDURE

NOTICE:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), and Air Pump Pulsation Pressure] (Click here).

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump and air switching valve and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 4 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure condition in Secondary Air Injection System Case 1: 
Air Pump
ON
Air Switching Valve
Open
Pressure
2.5 kPa (18.751 mmHg) or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure condition in Secondary Air Injection System Case 2: 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 2.5 kPa (18.751 mmHg)
Pulsation Detection
Exhaust gas pulsation detected

Pressure condition in Secondary Air Injection System Case 3: 
Air Pump
ON
Air Switching Valve
Closed
Pressure
2.5 kPa (18.751 mmHg) or more
Pulsation Detection
Slight pulsation detected

Pressure condition in Secondary Air Injection System Case 4: 
Air Pump
OFF
Air Switching Valve
Close
Pressure
Less than 2.5 kPa (18.751 mmHg)
Pulsation Detection
Exhaust pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the air switching valve is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

HINT:
  1. In case 3, as the air pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the air switching valve assembly, the average pressure is higher than in case 1 [approximately 20 to 30 kPa (150.120 to 225.018 mmHg)].
  2. In case 1, the average pressure is approximately 9 to 11 kPa (67.505 to 82.506 mmHg). The value of 2.5 kPa (18.751 mmHg) indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while secondary air injection Operating:
Air Pump ON, Air Switching Valve Open
Detected Condition while secondary air injection not Operating:
Air Pump OFF, Air Switching Valve Closed
ECM Determination
DTC Output
Case 1
Case 4
Normal
-
Case 1
Case 2
Air Switching Valve stuck open
P2440
Case 1
Case 3
Air pump stuck ON
P2444
Case 2
Case 4
Air pump stuck OFF
P2445
Case 3
Case 4
Air Switching Valve stuck closed
P2441
Case 1
Case 1
Air Switching Valve stuck open and Air pump stuck ON
P2440 and P2444
Case 2
Case 2
Air Switching Valve stuck open and Air pump stuck OFF
P2440 and P2445
Case 3
Case 3
Air Switching Valve stuck closed and Air pump stuck ON
P2441 and P2444
Case 4
Case 4
Air Switching Valve stuck closed and Air pump stuck OFF
P2441 and P2445

HINT:
  1. If the vacuum hose between the air switching valve assembly and the air pressure sensor is not connected correctly, case 4 may occur.
  2. By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending DTCs also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:
  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON and turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    6. Start the engine.
    7. Perform the secondary air injection system forced operation while the engine is idling.
    8. Check that the air pump assembly (AIR PUMP), air switching valve assembly (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream, indicate the conditions shown in the table below.

      Standard:

      Techstream Operation
      Air Pump
      Air Switching Valve
      Pressure*1
      Pulsation*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      2.5 kPa (18.751 mmHg) or more
      11.25 kPa (84.381 mmHg) or more
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Less than 2.5 kPa (18.751 mmHg)
      Less than 11.25 kPa (84.381 mmHg)

      *1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa (7.5 mmHg) or higher when the secondary air injection system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.
    9. Turn the ignition switch off.

      NOTICE:
      1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
        Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If an ERROR as shown in the illustration is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P2440 and/or P2441 is output
    A
    DTC P2440 and/or P2441, and P0412 are output
    B
    P2440 and/or P2441, and other DTCs (except P0412)
    C

If any DTCs other than P2440 and/or P2441 are output, troubleshoot those DTCs first.


B
GO TO AIR SWITCHING VALVE INSPECTION PROCEDURE

C
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
G034999E03
  1. Perform a visual check

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Disconnect the No. 1 air injection system hose.
      Text in Illustration 
      *1
      Air Switching Valve Assembly
      *2
      No. 1 Air Injection System Hose

    4. Connect the Techstream to the DLC3.

    5. Turn the ignition switch to ON and turn the Techstream on.

    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.

    8. Perform the secondary air injection system forced operation while the engine is idling.

    9. Place your hand near the air switching valve assembly port and check that the exhaust gas pressure pulsates when the ASV is turned on.

      CAUTION:
      To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.

    11. Check that the exhaust gas does not pulsate when the air switching valve assembly is turned off.

    12. Turn the ignition switch off.

      NOTICE:
      1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

      OK 
      Air Pump Operation
      Air Switching Valve Operation
      Exhaust Gas Pulsation
      ON
      OFF
      Not detected
      ON
      ON
      Detected

  1. Other inspection method:
    The air switching valve assembly operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
    Perform System Check operation under Manual Mode.
    *: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Connect the Techstream to the DLC3.

    4. Turn the ignition switch to ON and turn the Techstream on.

    5. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    6. Start the engine after the Techstream initialization is finished.

    7. Perform the secondary air injection system forced operation while the engine is idling.

    8. Check that the air fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream, indicate the conditions shown in the table below.

    9. Turn the ignition switch off.

      Standard:

      Air Injection System Operation
      Pulsation Condition
      (ECM Calculation)
      Air Fuel Ratio
      (Reference)
      AIR PUMP: ON, ASV: OPEN
      11.25 kPa (84.381 mmHg) or more
      18 or more
      AIR PUMP: OFF, ASV: CLOSE
      Less than 11.25 kPa (84.381 mmHg)
      Approximately 14.5
      (around stoichiometric air fuel ratio)

      Result 
      Result
      Proceed to
      NG
      A
      OK
      B

      HINT:
      REFERENCE:

      If the air pump assembly operation is confirmed as normal (Click here), the air fuel ratio detected in front of three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.



B
Go to step 9
A


3.INSPECT NO. 4 INTAKE PIPE (BLOCKAGES AND LEAKAGES)
G037122E03
  1. Check that the No. 4 intake pipe is securely connected to both the exhaust manifold and the air switching valve

  1. Inspect the No. 4 intake pipe for blockages and damage.
    Text in Illustration 
    *1
    No. 4 Intake Pipe

    OK:
    No blockages or damage on No. 4 intake pipe.



NG
REPLACE NO. 4 INTAKE PIPE
OK


4.INSPECT AIR SWITCHING VALVE ASSEMBLY (AIR SWITCHING VALVE OPERATION)
  1. Inspect the air switching valve assembly (Click here).



NG
REPLACE AIR SWITCHING VALVE ASSEMBLY (Click here)
OK


5.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A115629E05
  1. Disconnect the air injection control driver connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-5 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V (near battery voltage)
    A6-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)

  1. Measure the resistance according to valve(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A7-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Control Driver)



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


6.PERFORM ACTIVE TEST USING TECHSTREAM
A065741E74
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

  1. Start the engine after the Techstream initialization is finished.

  1. Operate the secondary air injection system using the System Check function and measure the voltage between the terminals of the ECM connector.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause damage to the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Text in Illustration 
    *a
    Component with wire harness connected
    (ECM)

    Techstream Operation
    Tester Connection
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    E4-24 (AIRV) - E4-3 (E1)
    3.5 to 7.5 V
    AIR PUMP: OFF, ASV: CLOSE
    E4-24 (AIRV) - E4-3 (E1)
    10 V or more



NG
Go to step 11
OK


7.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440 AND/OR P2441)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


NEXT

END 

9.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - AIR PRESSURE SENSOR)

OK:
No blockage and no deformation in vacuum hose.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


10.INSPECT AIR PRESSURE SENSOR
G034995E04
  1. Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying pressure to the air pressure sensor with the pressure gauge.
    Text in Illustration 
    *1
    Pressure Gauge
    *2
    Air Pressure Sensor

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure (Air Pump Pressure (Absolute) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

11.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E4-24 (AIRV) - A7-3 (SIV)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A7-3 (SIV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)