DTC P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 |
DTC P2441 Secondary Air Injection System Switching Valve Stuck Close Bank1 |
DTC P2442 Secondary Air Injection System Switching Valve Stuck Open Bank 2 |
DTC P2443 Secondary Air Injection System Switching Valve Stuck Closed Bank 2 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2440 | Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic). |
|
| The air switching valve (bank 1) is stuck open for 7 seconds while the engine is running (1 trip detection logic). | ||
| P2441 | The air switching valve (bank 1) is stuck close for 7 seconds while the engine is running (2 trip detection logic). |
|
| P2442 | Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic). |
|
| The air switching valve (bank 2) is stuck open for 7 seconds while the engine is running (1 trip detection logic). | ||
| P2443 | The air switching valve (bank 2) is stuck close for 7 seconds while the engine is running (2 trip detection logic). |
|
| Related DTCs | P2440: Air switching valve (bank 1) stuck open P2441: Air switching valve (bank 1) stuck closed P2442: Air switching valve (bank 2) stuck open P2443: Air switching valve (bank 2) stuck closed |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous: P2440 Case 2, P2442 Case 2 Once per drive cycle: Others |
| Duration | 2 seconds: P2440 Case 2, P2442 Case 2 7 seconds: Others |
| MIL Operation | 1 driving cycle: P2440, P2442 2 driving cycles: Others |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (Camshaft timing oil control valve) P0011, P0021 (VVT system - advance) P0012, P0022 (VVT System - retard) P0016, P0018 (VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0327, P0328, P0332, P0333 (Knock control sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P219A, P219B (Air-fuel ratio imbalance) P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor) |
| Battery voltage | 11 V or more |
| Atmospheric pressure | 45 kPa (338 mmHg) or higher |
| Engine | Running |
| Pressure pattern check during secondary air injection ON*1 | Completed |
| Pressure pattern check during secondary air injection OFF*2 | Completed |
| Pressure change check: secondary air injection ON*3 | Completed |
| Pressure pulsation check: secondary air injection OFF*4 | Completed |
| Air injection control driver (open/short or out of range) | Not detected |
| Secondary air injection system pressure sensor failure (open/short or out of range) | Not detected |
| *1: Pressure pattern check during secondary air injection ON | - |
| Time after secondary air injection starts operation | 5 seconds or more |
| Air pump | ON |
| Air switching valve | Open |
| Engine speed | Less than 3750 rpm |
| Engine speed | 680 rpm or more |
| Intake air amount per liter | Less than 100 gm/sec |
| Time after engine start | 5 second or more |
| *2: Pressure pattern check during secondary air injection OFF | - |
| Time after secondary air injection starts operation | 10 seconds or more |
| Air pump | OFF |
| Air switching valve | Closed |
| Engine speed | Less than 3000 rpm |
| Secondary air injection monitor during secondary air injection ON | Completed |
| Engine load | 7 to 60% |
| Time after engine start | 5 seconds or more |
| *3: Pressure change check: secondary air injection ON | - |
| Secondary air injection | Operating |
| Air pump | ON |
| Air switching valve (bank 1) | Open |
| Air switching valve (bank 2) | Closed |
| Secondary air injection system pressure sensor failure (open/short or out of range) | Not detected |
| Intake air amount per liter | Less than 15 gm/sec |
| *4: Pressure pulsation check: secondary air injection OFF | - |
| Pressure change check: secondary air injection ON | Completed |
| Pressure pulsation check: secondary air injection OFF | Not completed |
| Air pump | ON |
| Time after air switching valve (bank 1) closes | 0.3 seconds or more |
| Air switching valve (bank 2) | Open |
| Engine speed | Less than 5000 rpm |
| One of the following conditions is met | (a), (b) or (c) |
| (a) Cumulative intake air amount | 74 gm/sec or more |
| (b) Difference between starting temperature and current temperature | 30°C (54°F) or more |
| (c) Starting coolant temperature | 45°C (113°F) or more |
| Air pump | OFF |
| Air switching valve | Close |
| Engine speed | 5000 rpm or less |
| Air pressure sensor failure (open/short or out of range) | Not detected |
| Time after engine started | 5 seconds or more |
| Time after secondary air injection starts operation | 10 seconds or more |
| Air switching valve stuck (DTC P2440, P2442) | Not detected |
| Air pressure sensor stuck (DTC P2445) | Not in operation |
| Engine load | 20% or more |
| One of the following conditions is met | (a), (b) or (c) |
| (a) Condition 2 (secondary air injection ON) and Condition 2 (secondary air injection OFF) | Met |
| (b) Condition 1 (secondary air injection ON), Condition 1 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF | Met |
| (c) Condition 1 (secondary air injection ON), Condition 2 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF | Met |
| One of the following conditions is met | (a), (b) or (c) |
| (a) Condition 2 (secondary air injection ON) and Condition 2 (secondary air injection OFF) | Met |
| (b) Condition 1 (secondary air injection ON) and Condition 1 (secondary air injection OFF) | Met |
| (c) Condition 1 (secondary air injection ON) and Condition 2 (secondary air injection OFF) | Met |
| Cumulative pressure pulsation | 60 kPa (450 mmHg) or more |
| One of the following conditions is met | (a), (b), (c) or (d) |
| (a) Condition 3 (secondary air injection ON) | Met |
| (b) Condition 1 (secondary air injection ON), Condition 3 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF | Met |
| (c) Condition 1 (secondary air injection ON), Condition 4 (secondary air injection OFF), no pressure change detected when secondary air injection ON and pressure pulsation detected when secondary air injection OFF | Met |
| (d) Condition 4 (secondary air injection ON) | Met |
| One of the following conditions is met | (a), (b) or (c) |
| (a) Condition 3 (secondary air injection ON) | Met |
| (b) Condition 1 (secondary air injection ON), pressure change detected when secondary air injection ON and no pressure pulsation detected when secondary air injection OFF | Met |
| (c) Condition 4 (secondary air injection ON) | Met |
| Both of the following conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | 1.25 kPa (9.3 mmHg) or more |
| Secondary air injection pressure | 1 kPa (7.5 mmHg) or more |
| Both of the following conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | 1.25 kPa (9.3 mmHg) or more |
| Secondary air injection pressure | Less than 1 kPa (7.5 mmHg) |
| Both of the following conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | Less than 1.25 kPa (9.3 mmHg) |
| Secondary air injection pressure | 1 kPa (7.5 mmHg) or more |
| Both of the following conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | Less than 1.25 kPa (9.3 mmHg) |
| Secondary air injection pressure | Less than 1 kPa (7.5 mmHg) |
| Both of the following conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | 10 kPa (75 mmHg) or more |
| Secondary air injection pressure | 3 kPa (22.5 mmHg) or more |
| Both of the following conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | 10 kPa (75 mmHg) or more |
| Secondary air injection pressure | Less than 3 kPa (22.5 mmHg) |
| Both of the following conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | Less than 10 kPa (75 mmHg) |
| Secondary air injection pressure | 3 kPa (22.5 mmHg) or more |
| Both of the following conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | Less than 10 kPa (75 mmHg) |
| Secondary air injection pressure | Less than 3 kPa (22.5 mmHg) |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1 kPa (7.5 mmHg) or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Below 3 kPa (22.5 mmHg) |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1 kPa (7.5 mmHg) or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Below 3 kPa (22.5 mmHg) |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1 kPa (7.5 mmHg) or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Below 3 kPa (22.5 mmHg) |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1 kPa (7.5 mmHg) or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Below 3 kPa (22.5 mmHg) |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Condition while secondary air injection Operating: Air Pump ON, Air Switching Valve Open | Detected Condition while secondary air injection not Operating: Air Pump OFF, Air Switching Valve Closed | ECM Determination | DTC Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | Air switching valve stuck open | P2440 and/or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 |
| Case 3 | Case 8 | Air switching valve stuck closed | P2441 and/or P2443 |
| Case 1 | Case 5 | Air switching valve stuck open and air pump stuck ON | P2440 and/or P2442 and P2444 |
| Case 2 | Case 6 | Air switching valve stuck open and air pump stuck OFF | P2440 and P2442 and P2445 |
| Case 3 | Case 7 | Air switching valve stuck closed and air pump stuck ON | P2441 and P2443 and P2444 |
| Case 4 | Case 8 | Air switching valve stuck closed and air pump stuck OFF | P2441 and P2443 and P2445 |
| Techstream Operation | Air Pump Assembly | Air Switching Valve Assembly | Pressure*1 | Pulsation*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 1 kPa (7.5 mmHg) or higher | 1.25 kPa (9.3 mmHg) or higher |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Below 3 kPa (22.5 mmHg) | Below 10 kPa (75 mmHg) |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2440, P2441, P2442 and/or P2443 | A |
| P2440 and/or P2441 and P0412 | B |
| P2442 and/or P2443 and P0416 and/or P0417 | C |
| P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412, P0416 and P0417) are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION) |
![]() |
Perform a visual check:
Start the engine and warm it up.
Turn the ignition switch off.
Disconnect the No. 4 and No. 5 air injection system hoses.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Place your hand near the air switching valve assembly port and check that the exhaust gas pressure pulsates when the air switching valve assembly is turned on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: ON, ASV1: CLOSE, ASV2: CLOSE.
Check that the exhaust gas does not pulsate when the ASV is turned off.
Turn the ignition switch off.
| Air Pump Assembly Operation | Air Switching Valve Assembly Operation | Exhaust Gas Pulsation |
| ON | OFF | Not detected |
| ON | ON | Detected |
| *1 | Air Switching Valve (bank 1) |
| *2 | Air Switching Valve (bank 2) |
|
| ||||
| OK | |
| 3.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the Techstream.
|
| ||||
| OK | ||
| ||
| 4.INSPECT AIR TUBE (BLOCKAGE AND LEAK) |

Check that the No. 1 and No. 2 air tubes are securely connected to both the exhaust manifold and the air switching valve assembly.
Inspect the air tube for blockages and damage.
|
| ||||
| OK | |
| 5.INSPECT AIR SWITCHING VALVE ASSEMBLY |
Inspect the air switching valve assembly (Click here).
|
| ||||
| OK | |
| 6.INSPECT AI VALVE RELAY |
![]() |
Remove the AI VALVE relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | No battery voltage is applied across terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage is applied across terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AI VALVE RELAY) |
![]() |
Remove the AI VALVE relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (AI VALVE relay holder) - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | Air Injection VSV Relay (AI VALVE) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (AI VALVE RELAY - ECM) |
Remove the AI VALVE relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (AI VALVE relay holder) - E11-21 (AIR1) | Always | Below 1 Ω |
| 2 (AI VALVE relay holder) or E11-21 (AIR1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A7-1 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| A7-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E9-26 (AIRV) - A7-3 (SIV) | Always | Below 1 Ω |
| E9-26 (AIRV) or A7-3 (SIV) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the air injection control driver connector.
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
| Tester Connection | Condition | Specified Condition |
| A7-3 (SIV) - A7-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A7-3 (SIV) - A7-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Turn the ignition switch off.
![]() |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
| Tester Connection | Condition | Specified Condition |
| A7-4 (SIP) - A7-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A7-4 (SIP) - A7-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Turn the ignition switch off.
|
| ||||
| OK | |
| 12.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing Next.
Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
Read pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||