Home › ENGINE ยท 2TR-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > INSTALLATION

for Preparation Click here



1. INSTALL CYLINDER HEAD GASKET


A097915E04
  1. Apply continuous beads of seal packing to the cylinder block upper side and cylinder head gasket upper side as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal width:
    4 to 7 mm (0.15 to 0.28 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head gasket within 3 minutes of applying the seal packing.
    3. Install the cylinder head bolt within 15 minutes of applying the seal packing.
    4. Do not pour in engine oil for at least 4 hours after installation.



    G037323E01
  1. Place a new cylinder head gasket on the cylinder block surface with the Lot No. stamp facing upward.

    NOTICE:
    1. Make sure that the cylinder head gasket is installed in the correct direction.
    2. Place the cylinder head gently in order to avoid damaging the gasket with the bottom part of the head.



2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 2 successive steps.

  1. Place the cylinder head on the cylinder block.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    G037293E03
  1. Using several steps, uniformly install and tighten the 10 cylinder head bolts with plate washers in the sequence shown in the illustration.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



    A097917E04
  1. Mark the front of the cylinder head bolt head with paint.

  1. Retighten the cylinder head bolts by 90° in the same order as in step (c).

  1. Retighten the cylinder head bolts by an additional 90°.

  1. Check that the painted mark is at a 180° from the original position.



    A097918E03
  1. Seal packing will seep out on the engine's front side. Thoroughly wipe clean any seal packing.

  1. Install the wire harness bracket with the bolt.

  1. Install the wire harness with the bolts.

  1. Connect the engine coolant temperature sensor connector.

  1. Install the water hose.



3. INSPECT VALVE LASH ADJUSTER ASSEMBLY


A097867E02

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.

  1. Place the lash adjuster into a container full of engine oil.

  1. Insert the tip of SST into the lash adjuster's plunger and press down the checkball inside the plunger.

    SST
    09276-75010  

  1. Firmly hold SST and lash adjuster together and move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of the SST is actually pressing the checkball as shown in the illustration. If the checkball is not pressed, the air will not bleed.

  1. After bleeding the air, remove SST. Then quickly and firmly press the plunger with a finger.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the lash adjuster.



4. INSTALL VALVE LASH ADJUSTER ASSEMBLY


G037290E01
  1. Install the valve lash adjuster.



5. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


G037288E01
  1. Install the 16 valve rocker arms.



6. INSTALL CAMSHAFT


A115992E01

NOTICE:
Check that the valve rocker arm is correctly set as shown in the illustration.

  1. Apply clean engine oil to the camshaft's cam portion and the cylinder head journals.

  1. Install the chain onto the camshaft timing gear, with the painted mark of the link aligned with the timing mark of the camshaft timing gear.



    A097874E01
  1. Set the 2 camshafts as shown in the illustration.

    NOTICE:
    Align the paint mark with the timing mark before setting the camshaft.



    G037331E03
  1. Provisionally install the No. 1 camshaft bearing cap.

  1. Check the proper location of each No. 2 camshaft bearing cap and install each one.



    G037284E05
  1. Install a new O-ring onto the No. 1 camshaft bearing cap.

  1. Provisionally install the camshaft oil delivery pipe.



    G038225E02
  1. Tighten the bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for bolt A
    16 N*m{ 158 kgf*cm , 11 ft.*lbf } for bolts except bolt A



    A097877E03
  1. Check that each timing mark is set in the position shown in the illustration.



    A097878E04
  1. Install the timing chain onto the camshaft timing gear, with the paint mark aligned with the timing mark on the camshaft timing gear.

  1. Align the No. 2 camshaft straight pin and camshaft timing gear straight pin hole. Then install the camshaft timing gear onto the No. 2 camshaft.

    NOTICE:
    If the straight pin and straight pin hole are difficult to align, slightly rotate the No. 2 camshaft to the left and right using the hexagonal lobe of the camshaft. Then attempt to align them again.



    A097863E05
  1. Hold the hexagonal lobe of the No. 2 camshaft with the adjustable wrench.

  1. Tighten the bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Remove the 3.0 mm (0.118 in.) diameter bar from the chain tensioner.

  1. Apply adhesive to 2 or 3 threads of the timing gear case with head straight screw plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A086539E01
  1. Using a 10 mm socket hexagon wrench, install the timing gear case with head straight screw plug.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }



7. INSTALL NO. 1 CHAIN VIBRATION DAMPER


G037280E04
  1. Install the vibration damper with the bolt and nut.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



8. INSTALL CHAIN SUB-ASSEMBLY


G037332E03
  1. As shown in the illustration, install the chain onto the sprocket and gear with the painted marks aligned with the timing marks on the sprocket and gear.

    HINT:
    1. The camshaft mark plate is orange.
    2. The crankshaft mark plate is yellow.



    G037333E01
  1. Use a rope to tie the chain of the crankshaft timing sprocket. Tie the rope near the sprocket.

    NOTICE:
    After the chain tensioner has been installed, the rope must be removed.

    HINT:
    The rope is tied to prevent gear jumping.



9. INSTALL CHAIN TENSIONER SLIPPER


G037281E03
  1. Install the tensioner slipper with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


G037279E01
  1. Install a new gasket and the chain tensioner with the bolt and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



11. INSTALL TIMING CHAIN GUIDE


G037278E05
  1. Install a new O-ring and the chain guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



12. INSTALL TIMING CHAIN COVER


G036021E01
  1. Apply adhesive to the head straight screw plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 10 mm socket hexagon wrench, install the head straight screw plug.

    Torque:
    17 N*m{ 170 kgf*cm , 12 ft.*lbf }



    G038245E01
  1. Install 4 new O-rings onto the oil pump as shown in the illustration.



  1. Apply continuous beads of seal packing to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal width::
    Position
    Specified Condition
    A - A'
    2.5 to 3.0 mm (0.098 to 0.118 in.)
    B - B', C - C'
    4.0 to 4.5 mm (0.157 to 0.177 in.)
    D - D'
    2.5 to 3.0 mm (0.098 to 0.118 in.)
    E
    2.5 to 3.5 mm (0.098 to 0.138 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    3. Do not start the engine for at least 4 hours after installation.



    G039453E01



    G037336E02
  1. Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover onto the crankshaft.

  1. Loosely install the oil pump with the 19 bolts and 2 nuts, but do not tighten the bolts and nuts yet.



    G038836E01
  1. Provisionally install the oil pump with the 19 bolts and 2 nuts.

    NOTICE:
    If the vehicle is equipped with air conditioning, install bolts A' and B' when installing the idle pulley with bracket since they are for this purpose.

    HINT:
    Bolt length:
    75 mm (2.95 in.) for bolt A, B
    87 mm (3.43 in.) for bolt C
    95 mm (3.74 in.) for bolt D
    35 mm (1.37 in.) for bolt E

  1. Fully tighten the bolts and nuts, except bolts A, in the following order: Area 1, Area 3 and then Area 2.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Fully tighten the bolts A in the following order: Area 2 and then Area 3.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



  1. Fully tighten the bolts E in Area 4.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    G037337E03



    G038244E01
  1. Install a new gasket, then install the water by-pass pipe No. 1 with the 2 nuts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



13. INSTALL OIL PAN SUB-ASSEMBLY


G037340E03
  1. Apply continuous beads of seal packing to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal width:
    2 to 3 mm (0.079 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    G038130E02
  1. Loosely install the oil pan with the 16 bolts and 2 nuts.

    HINT:
    Bolt length:
    20 mm (0.79 in.) for bolt A,
    40 mm (1.57 in.) for bolt B

  1. Uniformly tighten the 16 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



14. INSTALL OIL STRAINER SUB-ASSEMBLY


G037268E01
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



15. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


G038131E02
  1. Apply continuous beads of seal packing to the places shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal width:
    3 to 4 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    G037265E02
  1. Provisionally install the oil pan with the 18 bolts and 2 nuts.

  1. Uniformly tighten the 18 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install a new gasket and the drain plug.



16. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY


17. INSTALL CRANKSHAFT PULLEY


G037557E02
  1. Align the set key of the crankshaft with the key groove of the pulley, and slide on the pulley.

  1. Provisionally install a new crankshaft pulley bolt onto the crankshaft.

  1. Using SST, hold the crankshaft pulley and tighten the crankshaft pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    260 N*m{ 2,651 kgf*cm , 192 ft.*lbf }

    NOTICE:
    Do not reuse the pulley bolt.



    G038205E01
  1. Install the bracket with the bolt. (w/ AIR CONDITIONING)

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



18. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A097879E03
  1. Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes of applying the seal packing.
    3. Do not apply engine oil for at least 2 hours of installation.



    G035202E06
  1. Provisionally install the cylinder head cover with the 19 bolts and 2 nuts.

  1. Tighten bolts A shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Tighten bolts B and nuts shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Tighten bolts A again.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    G038216E01
  1. Connect the ventilation hose.



    G038215E01
  1. Install the ignition coils with the bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    G038214E01
  1. Install the engine wire harness clamps.

  1. Connect the camshaft position sensor connector.

  1. Connect the VSV connector.

  1. Connect the throttle with motor body connector.

  1. Connect the ignition coil connectors.



19. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET


G037711E01
  1. Install a new gasket onto the intake manifold.

  1. Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    G037710E01
  1. Connect the engine wire harness to the relay block.

  1. Install the nut shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 connectors.



    G037709E01
  1. Install the harness clamp bracket with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Engage the wire harness clamp.

  1. Connect the compressor magnetic clutch connector. (w/ AIR CONDITIONING)

  1. Engage the engine wire harness clamp.

  1. Connect the VSV connector.



    G039455E01
  1. Connect the ventilation hose No. 3.



    G039454E01
  1. Connect the water by-pass hose No. 2.



    G037706E01
  1. Install the clamp bracket with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    G037705E01
  1. Connect the vacuum hose.



    G037704E01
  1. Connect the fuel vapor feed hose to the VSV.



20. INSTALL CAMSHAFT POSITION SENSOR


G037911E01
  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.



    G037910E01
  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Connect the camshaft position sensor connector.



21. INSTALL CRANKSHAFT POSITION SENSOR


G037911E01
  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.



    G037910E01
  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed when installing.

  1. Connect the camshaft position sensor connector.



22. INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)


G037912E03
  1. Using several steps, uniformly install and tighten the 5 bolts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf } for bolt A
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt B, C



23. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


A099635E01
  1. Install the No. 1 idler pulley sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



24. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


G037873E01
  1. Provisionally install the V-ribbed belt tensioner with bolts A and B.

  1. Tighten bolt B.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Check that the bolt holes of the V-ribbed belt tensioner and timing chain cover are aligned, and install bolt C.



    G038565E01
  1. Tighten bolt C.

    Torque:
    43 N*m{ 434 kgf*cm , 32 ft.*lbf }



25. INSTALL EXHAUST MANIFOLD


A154177
  1. Install a new gasket and the exhaust manifold with 8 new nuts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



26. INSTALL AIR SWITCHING VALVE ASSEMBLY


G037939E01
  1. Install a new gasket onto the cylinder head.

  1. Install the air switching valve with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    G037938E01
  1. Connect the air switching valve connector.

  1. Connect the vacuum hose.



27. INSTALL INTAKE PIPE INSULATOR


G037937E01
  1. Install 2 new gaskets onto the cylinder head and air switching valve.

  1. Install the intake pipe insulator with the 4 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



28. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


G037935E01
  1. Install the exhaust manifold heat insulator No. 1 with the 5 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



29. INSTALL GENERATOR ASSEMBLY


G038189E01
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    G038188E01
  1. Connect the generator connector.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



30. INSTALL INTAKE AIR CONNECTOR


    G037697E01
  1. Install the intake air connector with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts.

    Torque:
    5 N*m{ 51 kgf*cm , 44 in.*lbf }



    G037696E01
  1. Connect the vacuum hose.



    G037695E01
  1. Connect the ventilation hose No. 2.



    G037694E01
  1. Connect the vacuum hose.

  1. Engage the wire harness clamp.

  1. Connect the pressure sensor connector.



31. INSTALL REAR END PLATE
  1. Install the rear end plate with the 2 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



32. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)


G038107E01
  1. Clean the 10 bolts and 10 bolt holes.

  1. Apply adhesive to 2 or 3 threads of the 10 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Provisionally install the drive plate spacer front, drive plate and ring gear and drive plate rear with the 10 bolts.

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A099868E06
  1. Using several steps, uniformly install and tighten the 10 bolts in the sequence shown in the illustration.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



33. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


G038107E01
  1. Clean the 10 bolts and 10 bolt holes.

  1. Apply adhesive to 2 or 3 threads of the 10 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    G035062E04
  1. Using several steps, uniformly install and tighten the 10 bolts in the sequence shown in the illustration.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }



    G035063E01
  1. Mark the bolts with paint as shown in the illustration.

  1. Retighten the bolts by 90° in the same sequence as in step (d).

  1. Check that the paint mark of each bolt is at a 90° from the original position.

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



34. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


35. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


36. INSTALL ENGINE ASSEMBLY


G038554E01
  1. Attach the engine sling device and chain block to the engine hangers.

  1. Keep the engine level, and align the engine mounting bracket front No. 1 RH w/ engine mounting insulator front and LH with the body mountings.

  1. Attach the engine mounting bracket front No. 1 RH w/ engine mounting insulator front and LH, and install the 4 bolts and nuts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Remove the bolts, then remove the engine hangers.



37. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
Transmission
See page
A340E
Click here
A340F
Click here


38. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
Transmission
See page
R155
Click here
R155F
Click here


39. INSTALL EXHAUST PIPE ASSEMBLY FRONT


G038189E01
  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    G038188E01
  1. Connect the generator connector.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.



40. INSTALL EXHAUST PIPE ASSEMBLY TAIL
  1. Install a new gasket onto the exhaust pipe front.

  1. Install the exhaust pipe tail onto the 4 exhaust pipe supports.

  1. Tighten the 2 bolts and 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



41. CONNECT ENGINE WIRE


42. CONNECT NO. 1 AIR INJECTION HOSE


G038553E01
  1. Connect the fuel vapor feed hose.



43. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY


44. CONNECT NO. 2 FUEL HOSE


G037904E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



45. CONNECT FUEL HOSE


G037903E01
  1. Align the fuel hose connector with the pipe stem, and insert the fuel hose until the retainer makes a "click" sound.

  1. Push down the checker of the fuel hose.

    NOTICE:
    1. Check that there are no scratches or foreign objects around the disconnected parts of the fuel hose connector and pipe before performing this work.
    1. After connecting the fuel hose, check that the fuel hose is securely connected by pulling the fuel hose connector and pipe.

  1. Push the fuel hose down until the checker of the fuel hose makes a "click" sound.



46. INSTALL WATER HOSE SUB-ASSEMBLY


G038551E01
  1. Install the water hose.



47. INSTALL RADIATOR HOSE INLET


48. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (With Air Conditioning)


G038234E01
  1. Install the compressor and magnetic clutch with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the compressor and magnetic clutch connector.



    G038205E01
  1. Install the bolt shown in the illustration.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



49. INSTALL NO. 2 RADIATOR HOSE


50. INSTALL VANE PUMP ASSEMBLY


G037555E01
  1. Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the vane pump connector.



51. INSTALL AIR CLEANER CASE
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



52. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


53. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


G037934E01
  1. Install the air cleaner cap together with the air cleaner hose No. 1.

  1. Connect the 2 air cleaner clamps.

  1. Tighten the hose clamp bolt, then connect the air cleaner hose No. 1.

  1. Connect the wire harness clamp.

  1. Connect the mass air flow meter connector.



54. INSTALL FAN SHROUD


G038211E02
  1. Install the fan pulley.



    G038210E02
  1. Install the fan shroud and fan with fluid coupling together.

    NOTICE:
    Make sure that the fan shroud and fan with fluid coupling do not make any contact with the radiator when they are installed.

  1. Provisionally install the fan with fluid coupling with the 4 nuts.



    G038564E01
  1. Install the 2 bolts shown in the illustration.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    G038208E02
  1. Connect the oil cooler inlet and outlet hoses to the fan shroud. (for Automatic Transmission)



    G038207E02
  1. Connect the radiator reserve tank hose to the radiator.

  1. Install the fan generator V belt.



    A086838E02
  1. Tighten the 4 nuts shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



55. INSTALL RADIATOR SUPPORT TO FRAME SEAL LH


G038206E01
  1. Install the radiator support frame seal LH with the 9 clips.



56. INSTALL BATTERY TRAY


57. INSTALL BATTERY


58. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Standard engine oil:

    Oil grade
    Oil viscosity (SAE)
    ILSAC multigrade engine oil
    0W-20


    Standard capacity:

    Item
    Specified Condition
    Drain and refill with oil filter change
    5.8 liters (6.1 US qts, 5.1 Imp. qts)
    Drain and refill without oil filter change
    5.1 liters (5.4 US qts, 4.5 Imp. qts)
    Dry fill
    6.1 liters (6.4 US qts, 5.4 Imp. qts)



59. ADD ENGINE COOLANT
  1. Tighten the engine drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain plug.

  1. Disconnect the 2 vinyl hoses.

  1. Slowly fill the system with engine coolant.

    Capacity:
    M/T: 8.7 liters (9.2 US qts, 7.7 lmp. qts)
    A/T: 8.6 liters (9.1 US qts, 7.6 lmp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids.)
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant. When replacing the coolant, Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)) is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except OFF
    Temperature
    Toward warm
    Air condition switch
    OFF

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warning up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (d) through (k) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.

  1. Install the engine under cover No. 1 with the 4 bolts. (PRE RUNNER AND 4WD TYPE)

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



60. CHECK ENGINE OIL LEVEL


61. CHECK FOR FUEL LEAKAGE


62. CHECK FOR ENGINE COOLANT LEAKAGE


G038195E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Fluid and steam could be blown out under pressure.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump it up to 118 kPa (1.2 kgf/cm2, 17.1 psi) and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hose, radiator and water pump for leakage. If no external leakage is found, check the heater core, cylinder block and cylinder head.



63. CHECK FOR OIL LEAKAGE


64. CHECK FOR EXHAUST GAS LEAKAGE


65. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



66. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (for Pre Runner and 4WD Type, Regular Cab)
  1. Install the No. 2 engine under cover with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



67. INSTALL HOOD SUB-ASSEMBLY
(Click here)