Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type)

OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type) > Trouble in Passenger Airbag ON/OFF Indicator

for Preparation Click here


DESCRIPTION

This circuit detects the passenger seat occupant classification status (detected by the occupant classification system). The passenger airbag ON/OFF indicator illuminates ON or OFF comes on to inform the passengers of the front passenger airbag assembly status (activated or deactivated).

HINT:
The table below shows the normal indication condition of the passenger airbag ON/OFF indicator and the front passenger seat condition.

Front Passenger Seat Condition
ON Indicator
OFF Indicator
Adult is seated
ON
OFF
Child is seated
OFF
ON
Vacant
OFF
OFF
Occupant classification system failure
OFF
ON


WIRING DIAGRAM


C136275E01


INSPECTION PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (PERFORM SENSITIVITY CHECK)
  1. Perform the sensitivity check (Click here).

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 7
A


2.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT


3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (PERFORM SENSITIVITY CHECK)
  1. Perform the sensitivity check (Click here).



NG
Go to step 4
OK

END 

4.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
  1. Turn the ignition switch to ON.

  1. Using the Techstream, read the Data List (Click here).

    1. Read the display when the passenger side buckle switch is operated.

      Occupant Detection 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Passenger Buckle SW
      Buckle switch (Passenger side)/
      Unset: The seat belt is not fastened
      Set: The seat belt is fastened
      NG: Data is not determined
      Unset/Set
      -

      OK:
      The Techstream display changes correctly in accordance with the operation of the buckle switch.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)
OK


5.READ VALUE USING TECHSTREAM (SEAT BELT TENSION SENSOR)
  1. Fasten the passenger side seat belt.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, read the value of the Data List (Click here).

    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Filtered belt tension output
    Filtered belt tension output/
    Min.: 0 N
    Max.: 255 N
    39 to 64
    (no load)
    -

    OK:
    When there is no tension on the belt, 39 to 64 is displayed on the Techstream.



NG
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)
OK


6.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (PERFORM SENSITIVITY CHECK)
  1. Perform the sensitivity check (Click here).



NG
Go to step 7
OK

END 

7.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the following connectors are connected properly.

    1. Center airbag sensor assembly connector.
    2. Occupant classification ECU connector.
    3. Occupant classification sensor connector.
    4. Belt tension sensor (front seat outer belt assembly RH) connector.
    5. Front seat inner belt assembly RH connector.
    6. Seat position sensor connector.

    OK:
    The connectors are properly connected.

  1. Disconnect the following connectors.

    1. Center airbag sensor assembly connector.
    2. Occupant classification ECU connector.
    3. Occupant classification sensor connector.
    4. Belt tension sensor (front seat outer belt assembly RH) connector.
    5. Front seat inner belt assembly RH connector.
    6. Seat position sensor connector.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    NOTICE:
    Perform the zero point calibration if wire harnesses or connectors are repaired or replaced (Click here).

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



NG
REPLACE HARNESS OR CONNECTOR
OK


8.READ VALUE USING TECHSTREAM (PASSENGER CLASS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch off.



    H101938
  1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.

    NOTICE:
    1. Do not let the weight come into contact with the seatback when placing it on the seat cushion.
    2. Place the weight in the area shown in the illustration.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, read the value of the Data List (Click here).

    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Classification
    Passenger classification/
    NG: Data is not determined
    AM50: Adult is seated and seat is rear position
    AF05: Adult is seated and seat is front position
    CHILD: Child is seated
    OFF: Vacant
    AF05/AM50/CHILD/OFF
    -

    OK:
    The Techstream displays CHILD.

  1. Turn the ignition switch off.



    H101938
  1. Add 30 kg (66.1 lb) weight on the front passenger seat.

    NOTICE:
    1. Do not let the weight come into contact with the seatback when placing it on the seat cushion.
    2. Place the weight in the area shown in the illustration.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, read the value of the Data List (Click here).

    HINT:
    AF05 appears on the Techstream screen display when the seat is in the front position, and AM50 appears when the seat is in the rear position.


    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Classification
    Passenger classification/
    NG: Data is not determined
    AM50: Adult is seated and seat is rear position
    AF05: Adult is seated and seat is front position
    CHILD: Child is seated
    OFF: Vacant
    AF05/AM50/CHILD/OFF
    -

    OK:
    The Techstream displays AM50 or AF50 according to the seat position.



NG
Go to step 12
OK


9.REPLACE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the center airbag sensor assembly (Click here).


NEXT


10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (PERFORM SENSITIVITY CHECK)
  1. Perform the sensitivity check (Click here).



NG
Go to step 11
OK

END 

11.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Store the occupant classification ECU data into the Techstream (Click here).

    HINT:
    If the ECU data cannot be stored in the Techstream, replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor).

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Load the data from the previous ECU stored in the Techstream, into the newly installed ECU (Click here).


NEXT

END 

12.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Store the occupant classification ECU data into the Techstream (Click here).

    HINT:
    If the ECU data cannot be stored in the Techstream, replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor).

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Load the data from the previous ECU stored in the Techstream, into the newly installed ECU (Click here).


NEXT


13.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (PERFORM SENSITIVITY CHECK)
  1. Perform the sensitivity check (Click here).



NG
Go to step 14
OK

END 

14.REPLACE FRONT SEAT CUSHION ASSEMBLY (WITH OCCUPANT CLASSIFICATION ECU AND SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor) (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check the DTCs (Click here).

    OK:
    DTC B1774 and B1775 are not output.

    HINT:
    DTCs other than B1774 and B1775 may be output at this time, but they are not related to this check.


NEXT


15.PERFORM ZERO POINT CALIBRATION
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, perform the zero point calibration (Click here).


NEXT

END