Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Center airbag sensor assembly
  4. Combination meter assembly
  5. Yaw rate and deceleration sensor
  6. Master cylinder solenoid (skid control ECU)*1
  7. Brake actuator assembly (skid control ECU)*2
  8. Steering angle sensor
  9. No. 1 CAN junction connector
  10. No. 2 CAN junction connector
  1. *1: for Hydraulic Booster Type
  2. *2: for Vacuum Booster Type

WIRING DIAGRAM


E223284E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NEXT


3.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)


    E194173E30
  1. Disconnect the J19 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-6 (CANH) - D4-14 (CANL)
    Ignition switch off
    1 MΩ or higher

Text in Illustration 
*a
DLC3


NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)


    E194173E30
  1. Disconnect the J18 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-6 (CANH) - D4-14 (CANL)
    Ignition switch off
    108 to 132 Ω

Text in Illustration 
*a
DLC3


NG
Go to step 8
OK


6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - SKID CONTROL ECU)


    E223296E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-1 (CANH) - J18-3 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Hydraulic Booster Type)
    B
    NG (for Vacuum Booster Type)
    C



B
Go to step 14

C
Go to step 16
A


7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    E223296E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-2 (CANH) - J18-4 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)



NG
Go to step 18
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J18 No. 2 CAN junction connector connector.


NEXT


9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)


    E211086E52
  1. Disconnect the J19 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-1 (CANH) - J19-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    E211086E53
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-6 (CANH) - J19-17 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)



NG
Go to step 20
OK


11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    E211086E54
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-5 (CANH) - J19-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)



NG
Go to step 22
OK


12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - YAW RATE AND DECELERATION SENSOR)


    E211086E55
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-3 (CANH) - J19-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)



NG
Go to step 24
OK


13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR - ECM)


    E211086E56
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-2 (CANH) - J19-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2TR-FE)
    C



B
Go to step 26

C
Go to step 28
A

REPLACE NO. 1 CAN JUNCTION CONNECTOR 

14.CONNECT CONNECTOR
  1. Reconnect the J18 No. 2 CAN junction connector connector.


NEXT


15.CHECK FOR SHORT IN CAN BUS WIRES (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))


    E223286E02
  1. Disconnect the S1 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-11 (CANH) - S1-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

16.CONNECT CONNECTOR
  1. Reconnect the J18 No. 2 CAN junction connector connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))


    E223287E02
  1. Disconnect the S1 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-25 (CANH) - S1-14 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

18.CONNECT CONNECTOR
  1. Reconnect the J18 No. 2 CAN junction connector connector.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    E221291E02
  1. Disconnect the C9 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    C9-8 (CANH) - C9-7 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

20.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


21.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    E223274E02
  1. Disconnect the S9 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S9-10 (CANH) - S9-9 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

22.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


23.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)


    E186790E17
  1. Disconnect the A21 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-13 (CANH) - A21-22 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

24.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


25.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE AND DECELERATION SENSOR)


    E223290E01
  1. Disconnect the Y1 yaw rate and deceleration sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Deceleration Sensor)



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE AND DECELERATION SENSOR (Click here)  

26.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


27.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    E214877E05
  1. Disconnect the E14 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E14-32 (CANH) - E14-31 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)  

28.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


29.CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    E223293E01
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-33 (CANH) - E7-34 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)