Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and GND when there is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.

Symptom
Trouble Area
There is resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3.
  1. Short to GND
  2. ECM
  3. Center airbag sensor assembly
  4. Combination meter assembly
  5. Yaw rate and deceleration sensor
  6. Master cylinder solenoid (skid control ECU)*1
  7. Brake actuator assembly (skid control ECU)*2
  8. Steering angle sensor
  9. No. 1 CAN junction connector
  10. No. 2 CAN junction connector
  1. *1: for Hydraulic Booster Type
  2. *2: for Vacuum Booster Type

WIRING DIAGRAM


E223284E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the ignition switch off before inspecting CAN bus wires for a ground short.
  3. After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NEXT


3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    E194173E29
  1. Disconnect the J19 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-6 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    D4-14 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CAN-H, CAN-L)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J19 No. 1 CAN junction connector connector.


NEXT


5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)


    E194173E29
  1. Disconnect the J18 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D4-6 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    D4-14 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    DLC3



NG
Go to step 8
OK


6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - SKID CONTROL ECU)


    E223297E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-1 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J18-3 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Hydraulic Booster Type)
    B
    NG (for Vacuum Booster Type)
    C



B
Go to step 14

C
Go to step 15
A


7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    E223297E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-2 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J18-4 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    DLC3



NG
Go to step 16
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J18 No. 2 CAN junction connector connector.


NEXT


9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)


    E214883E18
  1. Disconnect the J19 No. 1 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-1 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-12 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK


10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    E214883E19
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-6 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-17 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
Go to step 17
OK


11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    E214883E20
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-5 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-16 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
Go to step 18
OK


12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - YAW RATE AND DECELERATION SENSOR)


    E214883E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-3 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-14 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
Go to step 19
OK


13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR - ECM)


    E214883E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-2 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-13 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 1GR-FE)
    B
    NG (for 2TR-FE)
    C



B
Go to step 20

C
Go to step 21
A

REPLACE NO. 1 CAN JUNCTION CONNECTOR 

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MASTER CYLINDER SOLENOID (SKID CONTROL ECU))
  1. Disconnect the S1 master cylinder solenoid (skid control ECU) connector.



    E223297E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-1 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J18-3 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)  

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
  1. Disconnect the S1 brake actuator assembly (skid control ECU) connector.



    E223297E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-1 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J18-3 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    E223297E04
  1. Disconnect the C9 combination meter assembly (combination meter ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J18-2 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J18-4 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    E214883E19
  1. Disconnect the S9 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-6 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-17 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    E214883E20
  1. Disconnect the A21 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-5 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-16 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE AND DECELERATION SENSOR)


    E214883E21
  1. Disconnect the Y1 yaw rate and deceleration sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-3 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-14 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE YAW RATE AND DECELERATION SENSOR (Click here)  

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    E214883E22
  1. Disconnect the E14 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-2 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-13 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)  

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    E214883E22
  1. Disconnect the E7 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-2 (CANH) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-13 (CANL) - D4-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 CAN Junction Connector)
    *b
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CAN-H, CAN-L)
OK

REPLACE ECM (Click here)