Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab)

AUDIO AND VISUAL SYSTEM (for Regular Cab and Double Cab) > Speaker Circuit (Built-in Amplifier)

for Preparation Click here


DESCRIPTION

The stereo component amplifier sends sound signals to the speaker.

WIRING DIAGRAM


E146451E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result: 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area*
    B

    HINT:
    *: for Double Cab



B
Go to step 7
A


2.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result: 
    Result
    Proceed to
    Front No. 2 speaker
    A
    Front No. 1 speaker
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER


    E146506E02
  1. Disconnect the K11 and K13 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    3 (TWL+) - 4 (TWL-)
    Always
    3.6 to 4.4 Ω
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    3 (TWR+) - 4 (TWR-)
    Always
    3.6 to 4.4 Ω

    Result: 
    Result
    Proceed to
    OK
    A
    NG (for Regular Cab)
    B
    NG (for Double Cab)
    C



B
REPLACE FRONT NO. 2 SPEAKER (Click here)

C
REPLACE FRONT NO. 2 SPEAKER (Click here)
A


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)


    E146562E01
  1. Disconnect the K1 receiver connector.

  1. Disconnect the K11 and K13 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K1-2 (FL+) - K13-3 (TWL+)
    Always
    Below 1 Ω
    K1-6 (FL-) - K13-4 (TWL-)
    K1-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    K1-6 (FL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K1-1 (FR+) - K11-3 (TWR+)
    Always
    Below 1 Ω
    K1-5 (FR-) - K11-4 (TWR-)
    K1-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    K1-5 (FR-) - Body ground

    Result: 
    Result
    Proceed to
    NG
    A
    OK (for Column Shift Type)
    B
    OK (for Floor Shift Type)
    C



B
REPLACE RADIO RECEIVER (Click here)

C
REPLACE RADIO RECEIVER (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.INSPECT FRONT NO. 1 SPEAKER


    E144966E01
  1. Disconnect the M8 and N10 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Result: 
    Result
    Proceed to
    OK
    A
    NG (for Regular Cab)
    B
    NG (for Double Cab)
    C



B
REPLACE FRONT NO. 1 SPEAKER (Click here)

C
REPLACE FRONT NO. 1 SPEAKER (Click here)
A


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)


    E108122E20
  1. Disconnect the M8, N10, K11 and K13 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K13-1 (+) - N10-1
    Always
    Below 1 Ω
    K13-2 (-) - N10-2
    K13-1 (+) - Body ground
    Always
    10 kΩ or higher
    K13-2 (-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K11-1 (+) - M8-1
    Always
    Below 1 Ω
    K11-2 (-) - M8-2
    K11-1 (+) - Body ground
    Always
    10 kΩ or higher
    K11-2 (-) - Body ground

    Result: 
    Result
    Proceed to
    NG
    A
    OK (for Regular Cab)
    B
    OK (for Double Cab)
    C



B
REPLACE FRONT NO. 2 SPEAKER

C
REPLACE FRONT NO. 2 SPEAKER
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

7.INSPECT REAR NO. 1 SPEAKER


    E144966E02
  1. Disconnect the O1 and O7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE REAR NO. 1 SPEAKER
OK


8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR NO. 1 SPEAKER)


    E146563E01
  1. Disconnect the K2 receiver connector.

  1. Disconnect the O1 and O7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K2-2 (RL+) - O7-1
    Always
    Below 1 Ω
    K2-6 (RL-) - O7-2
    K2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    K2-6 (RL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K2-1 (RR+) - O1-1
    Always
    Below 1 Ω
    K2-3 (RR-) - O1-2
    K2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    K2-3 (RR-) - Body ground

    Result: 
    Result
    Proceed to
    NG
    A
    OK (for Column Shift Type)
    B
    OK (for Floor Shift Type)
    C



B
REPLACE RADIO RECEIVER (Click here)

C
REPLACE RADIO RECEIVER (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR