Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1905/74    Short in Front Passenger Side Pretensioner Squib Circuit

DTC    B1906/74    Open in Front Passenger Side Pretensioner Squib Circuit

DTC    B1907/74    Short to GND in Front Passenger Side Pretensioner Squib Circuit

DTC    B1908/74    Short to B+ in Front Passenger Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The front pretensioner squib RH circuit consists of the center airbag sensor and the front seat outer belt RH.
This circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front pretensioner squib RH circuit.

DTC Code
Detection Condition
Trouble Area
B1905/74
When all conditions below are met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib RH circuit during primary check.
  2. Front pretensioner squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1906/74
When all conditions below are met:
  1. The center airbag sensor receives an open circuit signal in the front pretensioner squib RH circuit for 2 seconds.
  2. Front pretensioner squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1907/74
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. Front pretensioner squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly
B1908/74
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds.
  2. Front pretensioner squib RH malfunction
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat outer belt assembly RH (Front pretensioner squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C146254E47


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK FRONT SEAT OUTER BELT RH (FRONT PRETENSIONER SQUIB RH)
C193224E02
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the front seat outer belt RH.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1905, B1906, B1907 or B1908 is not output (for Regular Cab)
    A
    DTC B1905, B1906, B1907 or B1908 is not output (for Double Cab)
    B
    DTC B1905, B1906, B1907 or B1908 is not output (for CrewMax)
    C
    DTC B1905, B1906, B1907 or B1908 is output
    D

    HINT:
    Codes other than DTC B1905, B1906, B1907, B1908 maybe output at this time, but they are not related to this check.



B
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)

C
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)

D
REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH (Click here)
A


2.CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the No. 2 floor wire connector (on the front seat outer belt RH side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
C193225E01
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q2-1 (R+) - Body ground
    Ignition switch ON
    Below 1 V
    Q2-2 (R-) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q2-1 (R+) - Q2-2 (R-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q2-1 (R+) - Q2-2 (R-)
    Always
    1 MΩ or higher
    Q2-1 (R+) - Body ground
    Q2-2 (R-) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR
C172068E03
  1. Connect the connectors to the front seat outer belt RH and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1905, B1906, B1907 or B1908 is output (for Column Shift Type)
    A
    DTC B1905, B1906, B1907 or B1908 is output (for Floor Shift Type)
    B
    DTC B1905, B1906, B1907 or B1908 is not output
    C

    HINT:
    Codes other than DTC B1905, B1906, B1907, B1908 maybe output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)