Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

DTC    B1595    No Response from Rear Seat Entertainment System

DTC    B15D5    Rear Seat Entertainment System Disconnected

for Preparation Click here


DESCRIPTION

The television display assembly and stereo component tuner assembly are connected by an AVC-LAN communication line.
The navigation receiver assembly is also connected to the stereo component tuner assembly by an AVC-LAN communication line.
This DTC will be stored when an AVC-LAN communication error occurs between the stereo component tuner assembly and television display assembly.

HINT:
If either B1595 or B15D5 and either B1561 or B159F are output, troubleshoot for B1561 or B159F first.


DTC Code
DTC Detection Condition
Trouble Area
B1595
Within the time-out period, there was no response from the television display assembly to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request
  1. Television display assembly power source circuit
  2. AVC-LAN circuit between stereo component tuner assembly and television display assembly
  3. Television display assembly
  4. Stereo component tuner assembly
  5. Navigation receiver assembly
B15D5*
When either condition below is met:
  1. The television display assembly is/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the television display assembly is not possible when the engine is started.

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM


E190159E02


INSPECTION PROCEDURE

NOTICE:
After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, registration of the XM radio ID is necessary.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs and check if the same trouble occurs again.
    Result 
    Result
    Proceed to
    B1595 or B15D5 is output.
    A
    Either B1595 or B15D5 and either B1561 or B159F are output.
    B
    No DTCs are output.
    C



B
GO TO DTC CHART (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.
      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)


    E176474E12
  1. Disconnect the W2 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-12 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    W2-16 (+B) - W2-12 (GND)
    Always
    11 to 14 V
    W2-15 (ACC) - W2-12 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - STEREO COMPONENT TUNER)


    E191660E01
  1. Disconnect the W2 television display assembly connector.

  1. Disconnect the K29 stereo component tuner assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    W2-14 (TX+) - K29-12 (TX1+)
    Always
    Below 1 Ω
    W2-13 (TX-) - K29-11 (TX1-)
    Always
    Below 1 Ω
    W2-14 (TX+) - Body ground
    Always
    10 kΩ or higher
    W2-13 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - MULTI-MEDIA INTERFACE ECU)


    E191661E01
  1. Disconnect the K27 stereo component tuner assembly connector.

  1. Disconnect the J108 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K27-9 (TX+) - J108-4 (TX2+)
    Always
    Below 1 Ω
    K27-10 (TX-) - J108-5 (TX2-)
    Always
    Below 1 Ω
    K27-9 (TX+) - Body ground
    Always
    10 kΩ or higher
    K27-10 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NAVIGATION RECEIVER)


    E191659E01
  1. Disconnect the J107 multi-media interface ECU connector.

  1. Disconnect the K8 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J107-9 (TX1+) - K8-9 (TXM+)
    Always
    Below 1 Ω
    J107-10 (TX1-) - K8-10 (TXM-)
    Always
    Below 1 Ω
    J107-9 (TX1+) - Body ground
    Always
    10 kΩ or higher
    J107-10 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE TELEVISION DISPLAY ASSEMBLY
  1. Replace the television display assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 10
OK

END (TELEVISION DISPLAY IS FAULTY) 

10.REPLACE STEREO COMPONENT TUNER ASSEMBLY
  1. Replace the stereo component tuner assembly with a new one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 11
OK

END (STEREO COMPONENT TUNER ASSEMBLY IS FAULTY) 

11.REPLACE MULTI-MEDIA INTERFACE ECU
  1. Replace the multi-media interface ECU with a new one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (MULTI-MEDIA INTERFACE ECU IS FAULTY)