NAVIGATION SYSTEM (for SD) > Speaker Circuit |

| 1.CHECK SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Malfunction in front speaker area | A |
| Malfunction in rear speaker area* | B |
|
| ||||
| A | |
| 2.CHECK FRONT SIDE SPEAKER |
Check the malfunctioning speakers.
| Result | Proceed to |
| Malfunction in front No. 2 speaker assembly | A |
| Malfunction in front No. 1 speaker assembly | B |
|
| ||||
| A | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Temporarily replace the front No. 2 speaker assembly with a new or normally functioning one.
Check that the speaker sounds normally.
| Result | Proceed to |
| OK | A |
| NG (for Regular Cab) | B |
| NG (for Double Cab) | C |
| NG (for CrewMax) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
Disconnect the K30 navigation receiver assembly connector.
Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K30-1 (FR+) - K11-3 (TWR+) | Always | Below 1 Ω |
| K30-5 (FR-) - K11-4 (TWR-) | Always | Below 1 Ω |
| K30-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| K30-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K30-2 (FL+) - K13-3 (TWL+) | Always | Below 1 Ω |
| K30-6 (FL-) - K13-4 (TWL-) | Always | Below 1 Ω |
| K30-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| K30-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Column Shift Type) | A |
| OK (for Floor Shift Type) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Regular Cab) | B |
| NG (for Double Cab) | C |
| NG (for CrewMax) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K11-1 (+) - M8-1 | Always | Below 1 Ω |
| K11-2 (-) - M8-2 | Always | Below 1 Ω |
| K11-1 (+) - Body ground | Always | 10 kΩ or higher |
| K11-2 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K13-1 (+) - N10-1 | Always | Below 1 Ω |
| K13-2 (-) - N10-2 | Always | Below 1 Ω |
| K13-1 (+) - Body ground | Always | 10 kΩ or higher |
| K13-2 (-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Column Shift Type) | A |
| OK (for Floor Shift Type) | B |
| NG | C |
|
| ||||
| OK | |
| 7.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWR+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWR-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 3 (TWL+) | Always | Below 1 Ω |
| 2 (-) - 4 (TWL-) | Always | Below 1 Ω |
| *A | for RH |
| *B | for LH |
| Result | Proceed to |
| OK (for Column Shift Type) | A |
| OK (for Floor Shift Type) | B |
| NG (for Regular Cab) | C |
| NG (for Double Cab) | D |
| NG (for CrewMax) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 8.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Result | Proceed to |
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
|
| ||||
|
| ||||
| A | |
| 9.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR NO. 1 SPEAKER ASSEMBLY) |
Disconnect the K31 navigation receiver assembly connector.
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K31-1 (RR+) - O1-1 | Always | Below 1 Ω |
| K31-3 (RR-) - O1-2 | Always | Below 1 Ω |
| K31-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| K31-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K31-2 (RL+) - O7-1 | Always | Below 1 Ω |
| K31-6 (RL-) - O7-2 | Always | Below 1 Ω |
| K31-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| K31-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK (for Column Shift Type) | A |
| OK (for Floor Shift Type) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||