Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1ABD    Short to +B in Buzzer

DTC    C1ABE    Short to GND or Open in Buzzer

for Preparation Click here


DESCRIPTION

  1. DTC C1ABD is stored when the blind spot monitor sensor LH detects a +B short in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.
  2. DTC C1ABE is stored when the blind spot monitor sensor LH detects a ground short or open in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.

DTC Code
DTC Detection Condition
Trouble Area
C1ABD
  1. Both of the following conditions are met:
    1. Blind spot monitor main switch assembly (warning canceling switch assembly) is on with ignition switch ON.
    2. The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.
  1. Blind spot monitor sensor LH
  2. Rear cross traffic alert buzzer (blind spot monitor buzzer)
  3. Harness or connector
C1ABE
  1. Both of the following conditions are met:
    1. Blind spot monitor main switch assembly (warning canceling switch assembly) is on with ignition switch ON.
    2. The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.
  1. Blind spot monitor sensor LH
  2. Rear cross traffic alert buzzer (blind spot monitor buzzer)
  3. Harness or connector

WIRING DIAGRAM


E254403E10


INSPECTION PROCEDURE

NOTICE:
  1. When checking for DTCs, make sure that the blind spot main switch assembly (warning canceling switch assembly) is on.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR LH)
  1. Disconnect the P19 rear cross traffic alert buzzer (blind spot monitor buzzer) connector.

  1. Disconnect the S5 blind spot monitor sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P19-2 (BZN) - S5-3 (BUZ)
    Always
    Below 1 Ω
    P19-2 (BZN) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P19-1 (BZP) - Body ground
    Ignition switch ON
    11 to 14 V
    P19-1 (BZP) - Body ground
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.REPLACE BLIND SPOT MONITOR BUZZER (REAR CROSS TRAFFIC ALERT BUZZER)
  1. Replace the rear cross traffic alert buzzer (blind spot monitor buzzer) with a new or normally functioning one.

    1. for Regular Cab: Click here
    2. for Double Cab: Click here
    3. for CrewMax: Click here


NEXT


4.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
REPLACE BLIND SPOT MONITOR SENSOR LH (Click here)
OK

END (REAR CROSS TRAFFIC ALERT BUZZER [BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)