Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  P0430  Catalyst System Efficiency Below Threshold (Bank 2)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the Air-Fuel Ratio (A/F) sensor, sends pre-catalyst information to the ECM. The second sensor, the Heated Oxygen (HO2) sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the TWC, the ECM calculates the Oxygen Storage Capacity (OSC) of the TWC. This calculation is based on the voltage output of the HO2 sensor while performing active air-fuel ratio control.

The OSC value is an indication of the oxygen storage capacity of the TWC. When the vehicle is being driven with a warm engine, active air-fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air-fuel ratio to lean or rich levels. If the rich-lean cycle of the HO2 sensor is long, the OSC becomes greater. There is a direct correlation between the OSCs of the HO2 sensor and the TWC.

The ECM uses the OSC value to determine the state of the TWC. If any deterioration has occurred, it illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0420 OSC value smaller than standard value under active air-fuel ratio control
(1 trip detection logic)
·

Gas leak from exhaust system

·

Air-Fuel Ratio (A/F) sensor (for Bank 1 Sensor 1)

·

Heated Oxygen (HO2) sensor (for Bank 1 Sensor 2)

·

Front No. 2 exhaust pipe assembly (TWC: Front catalyst and rear catalyst)

·

EGR valve


P0430 OSC value smaller than standard value under active air-fuel ratio control
(1 trip detection logic)
·

Gas leak from exhaust system

·

Air-Fuel Ratio (A/F) sensor (for Bank 2 Sensor 1)

·

Heated Oxygen (HO2) sensor (for Bank 2 Sensor 2)

·

Front exhaust pipe assembly (TWC: Front catalyst and rear catalyst)

·

EGR valve



CATALYST LOCATION

A310668E02
1.052,1.292 0.927,1.292 0.927,1.292 0.594,2.76 false 1.875,5.865 1.75,5.865 1.75,5.865 1.573,5.083 false 2.083,1.698 1.958,1.698 1.958,1.698 1.74,2.656 false 3.042,1.781 2.906,1.781 2.906,1.781 2.698,2.698 false 2.406,3.917 2.281,3.917 2.281,3.917 2.188,3.542 false 3.594,6.188 3.458,6.188 3.458,6.188 3.375,5.813 false 3.063,4 2.927,4 2.927,4 2.833,4.438 false 3.875,3.979 3.74,3.979 3.74,3.979 3.542,4.896 false 5.781,1.885 5.646,1.885 5.646,1.885 5.521,2.458 false 5.146,0.781 5.01,0.781 5.01,0.781 4.885,1.344 false 1.104,1.219 1.417,1.406 0.313,0.188 10 false *1 1.927,5.76 2.24,5.948 0.313,0.188 10 false *2 2.135,1.594 2.448,1.781 0.313,0.188 10 false *5 3.083,1.688 3.396,1.875 0.313,0.188 10 false *7 2.458,3.792 2.771,3.979 0.313,0.188 10 false *3 3.635,6.083 3.948,6.271 0.313,0.188 10 false *4 3.115,3.885 3.427,4.073 0.313,0.188 10 false *6 3.958,3.896 4.271,4.083 0.313,0.188 10 false *8 5.823,1.813 6.135,2 0.313,0.188 10 false *9 5.188,0.688 5.5,0.875 0.313,0.188 10 false *9

Text in Illustration
*1 Exhaust Manifold Sub-assembly RH *2 Exhaust Manifold Sub-assembly LH
*3 Front Exhaust Pipe Assembly (TWC: Front Catalyst and Rear Catalyst) *4 Front No. 2 Exhaust Pipe Assembly (TWC: Front Catalyst and Rear Catalyst)
*5 Air Fuel Ratio Sensor (for Bank 2 Sensor 1) *6 Air Fuel Ratio Sensor (for Bank 1 Sensor 1)
*7 Heated Oxygen Sensor (for Bank 2 Sensor 2) *8 Heated Oxygen Sensor (for Bank 1 Sensor 2)
*9 Center Exhaust Pipe Assembly *10 Tailpipe Assembly

MONITOR STRATEGY

Related DTCs P0420: Catalyst Deterioration (for Bank 1)
P0430: Catalyst Deterioration (for Bank 2)
Required Sensors/Components (Main) A/F sensor and HO2 sensor
Required Sensors/Components (Related) Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation Once per driving cycle
Duration About 30 seconds
MIL Operation 1 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058, P102D, P105D (Rear Oxygen Sensor Heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0136, P0156, P0137, P0157, P0138, P0158, P0139, P0159, P0606, P0607, P013A, P013C (Rear Oxygen Sensor)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
Battery voltage 11 V or more
Intake air temperature -10°C (14°F) or more
Engine coolant temperature 75°C (167°F) or more
Atmospheric pressure 76 kPa (570 mmHg) or more
Idling OFF
Engine RPM Less than 3200 rpm
A/F sensor status Activated
Fuel system status Closed loop
Engine load 10 to 75%
All of following conditions (a), (b) and (c) met -
(a) Mass air flow rate 7.5 to 75 gm/s.
(b) Estimated front catalyst temperature 480 to 820°C (896 to 1508°F)
(c) Estimated rear catalyst temperature 380 to 700°C (716 to 1292°F)
Transmission gear 4th or higher

TYPICAL MALFUNCTION THRESHOLDS

Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) Less than 1

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

HINT:
·

It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTCs P0420 and P0430. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.

·

Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.



U144560E02
1.271,4.688 1.552,4.406 1.552,4.406 1.656,4.406 false 0.26,0.635 1.208,0.792 0.948,0.156 10 false Vehicle Speed 0.125,1.104 1.271,1.302 1.146,0.198 10 false 60 km/h (37 mph) 0.865,2.208 1.271,2.438 0.406,0.229 10 false Idling 0.104,2.406 1.25,2.604 1.146,0.198 10 false Ignition Switch off 0.125,0.094 3.063,0.25 2.938,0.156 10 false Heated Oxygen Sensor Monitor Driving Pattern 0.125,3.573 2.76,3.729 2.635,0.156 10 false Catalyst Efficiency Monitor Driving Pattern 0.104,4.979 1.24,5.167 1.135,0.188 10 false 60 km/h (37 mph) 1.719,4.302 4.635,4.51 2.917,0.208 10 false Between 75 and 100 km/h (47 and 63 mph) 1.563,2.708 2.396,2.906 0.833,0.198 10 false Warming up 2.625,2.698 3.865,2.885 1.24,0.188 10 false 10 minutes or more 5.448,6.552 6.688,6.74 1.24,0.188 10 false 10 minutes or more 2.917,6.594 4.156,6.781 1.24,0.188 10 false 10 minutes or more 1.833,2.052 2.063,2.229 0.229,0.177 10 false [A] 3.135,0.969 3.625,1.146 0.49,0.177 10 false [B]* 4.281,0.969 4.51,1.146 0.229,0.177 10 false [C] 5.271,0.969 5.5,1.146 0.229,0.177 10 false [C] 6.25,0.969 6.479,1.146 0.229,0.177 10 false [C] 4.771,3.135 4.979,3.313 0.208,0.177 10 false [D] 5.771,3.135 5.979,3.313 0.208,0.177 10 false [D] 6.76,3.135 6.969,3.313 0.208,0.177 10 false [D] 6.938,2.177 7.146,2.354 0.208,0.177 10 false [E] 1.396,6.052 1.667,6.26 0.271,0.208 10 false [E] 3.417,4.844 3.76,5.021 0.344,0.177 10 false [H]* 5.948,4.458 6.448,4.635 0.5,0.177 10 false [J]* 4.365,6.969 4.563,7.146 0.198,0.177 10 false [I] 6.719,6.979 6.969,7.188 0.25,0.208 10 false [K] 1.698,6.969 1.896,7.146 0.198,0.177 10 false [F] 2.177,5.927 2.448,6.135 0.271,0.208 10 false [G] 1.917,6.563 2.688,6.75 0.771,0.188 10 false Warming up 0.854,6.01 1.271,6.25 0.417,0.24 10 false Idling 0.083,6.25 1.25,6.438 1.167,0.188 10 false Ignition Switch off 0.365,7.24 4.979,7.448 4.615,0.208 10 false *: Drive the vehicle while keeping the engine load as constant as possible.

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

8.

Check that Catalyst Efficiency / Current is Incomplete.

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

10.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


11.

With the shift lever in S, drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].

13.

Check the Test Value for RL F/C B1S2, RL F/C B2S2.

·

If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

·

If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.


14.

Turn the ignition switch off and wait for at least 30 seconds [F].

15.

Turn the ignition switch to ON and turn the Techstream on.

16.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].

17.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [I].



18.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

19.

Check if any DTCs are stored.

HINT:

If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.


20.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [J].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [K].



21.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

22.

Check if any DTCs are stored.

HINT:

If the monitor item does not change to Complete, and no DTCs are stored, drive the vehicle again under an increased load.


23.

If no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the A/F and HO2 sensors. This is to activate the sensors sufficiently to obtain the appropriate inspection results.


A364135E07
4.865,3.083 4.865,3.313 4.865,3.313 5.281,3.313 false 5.188,3.313 5.188,3.083 false 0.542,0.667 1.51,0.854 0.969,0.188 10 false Engine Speed 0.844,1.01 1.49,1.208 0.646,0.198 10 false 3000 rpm 0.833,1.552 1.479,1.75 0.646,0.198 10 false 2000 rpm 1.094,2.531 1.49,2.74 0.396,0.208 10 false Idling 0.24,2.76 1.521,2.958 1.281,0.198 10 false Ignition Switch OFF 2.063,2.396 2.302,2.604 0.24,0.208 10 false (b) 6.615,2.74 7.031,2.938 0.417,0.198 10 false Time 2.073,3.135 2.896,3.344 0.823,0.208 10 false Warming up 3.375,3.146 4.583,3.354 1.208,0.208 10 false At least 3 minutes 5.344,3.219 6.073,3.406 0.729,0.188 10 false 2 seconds 4.833,3.375 5.302,3.573 0.469,0.198 10 false Check 1.604,2.646 1.844,2.854 0.24,0.208 10 false (a) 3.594,0.896 3.833,1.073 0.24,0.177 10 false (c) 4.75,0.885 4.99,1.073 0.24,0.188 10 false (d) 5.052,1.438 5.292,1.625 0.24,0.188 10 false (d)

(a) Connect the Techstream to the DLC3.

(b) Start the engine and warm it up with all the accessories switched OFF until the engine coolant temperature stabilizes.

(c) Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes.

(d) While running the engine at 3000 rpm and 2000 rpm at 2 second intervals, check the waveforms of the A/F and HO2 sensors using the Techstream.


HINT:
·

If the voltage output of either the Air-Fuel Ratio (A/F) or Heated Oxygen (HO2) sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the Active Test Control the Injection Volume for A/F Sensor using the Techstream.

·

If the Three-Way Catalytic Converter (TWC) has deteriorated, the HO2 sensor (located behind the TWC) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).



A121610E37
0.058,0.04 4.756,0.235 4.698,0.195 10 Voltage output when active air-fuel ratio control not performed: 2.374,0.421 3.663,0.601 1.289,0.180 10 Normal Catalyst 4.744,0.426 6.604,0.574 1.860,0.148 10 Deteriorated Catalyst 0.257,2.118 1.115,2.640 0.858,0.522 10 Waveform of HO2 sensor behind TWC 0.257,0.653 1.269,1.297 1.012,0.644 10 Waveform of A/F sensor in front of TWC 1.446,0.789 1.823,0.937 0.378,0.148 10 3.5 V 1.446,1.123 1.845,1.266 0.399,0.143 10 3.0 V 1.446,2.104 1.793,2.253 0.347,0.150 10 1.0 V 1.446,2.774 1.736,2.922 0.290,0.148 10 0 V 2.64,3.111 3.396,3.257 0.755,0.146 10 10 seconds 5.042,3.08 5.796,3.221 0.755,0.141 10 10 seconds

CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171, P0174 (System Too Lean) and P0172, P0175 (System Too Rich).

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0420 or P0430 is output A
P0420 or P0430 and other DTCs are output B

HINT:

If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (A/F CONTROL)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).


g.

Monitor the voltage outputs of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Less than 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
-12.5% Lean More than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich More than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
-12.5% Lean Less than 0.4 V


Result:
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition Misfire Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leaks from exhaust system

·

EGR valve assembly


A
Lean Lean/Rich Air fuel ratio sensor malfunction - Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction - Air fuel ratio sensor
Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leaks from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leaks from exhaust system


Lean Lean Actual air fuel ratio lean May occur
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system

·

EGR valve assembly


D
Rich Rich Actual air fuel ratio rich -
·

Extremely rich or lean actual air fuel ratio

·

Gas leaks from exhaust system

·

EGR valve assembly




Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently more than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently less than 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

7.REPLACE AIR FUEL RATIO SENSOR

C

8.CHECK FOR EXHAUST GAS LEAK

D

10.CHECK EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

6.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NG

5.INSPECT EGR VALVE ASSEMBLY
5.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

6.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NG

6.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0420 A
P0430 B
P0420 and P0430 A and B



B

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

A

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

7.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

9.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

11.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

12.INSPECT EGR VALVE ASSEMBLY
12.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO

NG

13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO
a.

Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0171).



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the Techstream on.


e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
P0420 or P0430 is output A
DTC is not output B



A

15.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

B

END

15.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0420 A
P0430 B
P0420 and P0430 A and B



B

REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)

A

REPLACE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST)