Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  P0174  System Too Lean (Bank 2)  P0175  System Too Rich (Bank 2)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. DTC Detection Condition Trouble Area
P0171
P0174
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic)
·

Air induction system

·

Injector blockage

·

Mass Air Flow (MAF) meter

·

Engine Coolant Temperature (ECT) sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

PCV valve and hose

·

PCV hose connections

·

EGR valve assembly

·

ECM

·

Wire harness or connector


P0172
P0175
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic)
·

Injector leak or blockage

·

MAF meter

·

ECT sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in A/F sensor (for Sensor 1) circuit

·

A/F sensor (for Sensor 1)

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

A/F sensor heater and integration relay circuits

·

EGR valve assembly

·

ECM

·

Wire harness or connector



HINT:
·

When DTC P0171 or P0174 is stored, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is stored, the actual air-fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be stored. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is higher than 75°C [167°F]), the system is functioning normally.



MONITOR DESCRIPTION

Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

If the average fuel trim learning value is +35% or more, or -35% or less, the ECM interprets this as a fuel system malfunction.

A369480E07
1.802,1.938 1.521,1.938 false 1.854,3.073 1.49,3.25 false 1.646,0.573 3.458,0.771 1.813,0.198 10 false Fuel Compensation Amount 0.354,1.208 1.302,1.375 0.948,0.167 10 false P0171, P0174 1.896,1.854 2.25,2.042 0.354,0.188 10 false 1.35 1.917,2.99 2.271,3.177 0.354,0.188 10 false 0.65 0.26,1.646 1.469,2.188 1.208,0.542 10 false +35%: Malfunction Threshold of LEAN Condition 1.896,2.417 2.25,2.604 0.354,0.188 10 false 1.0 0.302,2.625 1.292,2.813 0.99,0.188 10 false P0172, P0175 0.292,2.979 1.49,3.542 1.198,0.563 10 false -35%: Malfunction Threshold of RICH Condition

MONITOR STRATEGY

Related DTCs P0171: Fuel trim lean (for Bank 1)
P0172: Fuel trim rich (for Bank 1)
P0174: Fuel trim lean (for Bank 2)
P0175: Fuel trim rich (for Bank 2)
Required Sensors/Components Air fuel ratio sensor, Mass air flow meter, Crankshaft position sensor
Frequency of Operation Continuous
Duration Within 10 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)
Fuel system status Closed loop
Battery voltage 11 V or more
Either of following conditions 1 or 2 met -
1. Engine RPM Less than 1100 rpm
2. Engine load 11.5% or more
Catalyst monitor Not executed

TYPICAL MALFUNCTION THRESHOLDS

Purge-cut Executing
Either of following conditions 1 or 2 met -
1. Average of short-term fuel trim and long-term fuel trim 35% or more (varies with engine coolant temperature)
2. Average of short-term fuel trim and long-term fuel trim -35% or less (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

A199233E22
0.568,0.043 1.536,0.247 0.968,0.205 10 Vehicle Speed 1.247,1.962 1.653,2.139 0.406,0.177 10 Idling 0.442,2.249 1.709,2.405 1.268,0.156 10 Ignition Switch ON 2.009,2.339 2.210,2.540 0.201,0.201 10 [A] 2.529,1.836 2.734,2.013 0.205,0.177 10 [B] 3.324,1.839 3.548,2.011 0.224,0.171 10 [C] 4.797,0.442 5.026,0.615 0.229,0.173 10 [D] 5.622,3.29 5.846,3.461 0.224,0.171 10 [E] 0.414,0.317 1.625,0.480 1.211,0.163 10 120 km/h (75 mph) 0.44,1.198 1.652,1.361 1.211,0.163 10 60 km/h (37 mph) 4.343,2.922 5.541,3.099 1.198,0.177 10 5 minutes or more 2.13,2.992 2.925,3.169 0.795,0.177 10 Warming up 2.858,3.146 4.014,3.323 1.156,0.177 10 2 minutes or more 3.636,0.059 7.009,0.262 3.373,0.202 10 Engine coolant temperature is 75°C (167°F) or higher 3.062,2.043 3.463,0.148 3.463,0.148 3.585,0.148 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at between 60 and 120 km/h (37 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0171, P0172, P0174 or P0175.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E] again.


14.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171, P0172, P0174 OR P0175)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0171, P0172, P0174 or P0175 is output A
P0171, P0172, P0174 or P0175 and other DTCs are output B


HINT:

If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

3.CHECK INTAKE SYSTEM

NG

3.CHECK INTAKE SYSTEM
HINT:

If a malfunction occurs when depressing the brake pedal, inspect the brake booster assembly, as there may be a vacuum leak in the brake booster assembly itself.


a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>1UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector blockage

·

Gas leaks from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter assembly

·

Manifold absolute pressure sensor

·

Engine coolant temperature sensor

·

EGR valve assembly


A
Rich Rich Actual air fuel ratio rich
·

Fuel injector leakage or blockage

·

Gas leaks from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter assembly

·

Manifold absolute pressure sensor

·

Engine coolant temperature sensor


A
Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor

·

EGR valve assembly


B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

5.READ VALUE USING TECHSTREAM (COOLANT TEMP)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING TECHSTREAM (COOLANT TEMP)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: Between 75°C and 100°C (167°F and 212°F).


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

6.READ VALUE USING TECHSTREAM (MAF)

NG

6.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off).




OK

7.CHECK FUEL PRESSURE

NG

18.CHECK HARNESS AND CONNECTOR
7.CHECK FUEL PRESSURE
a.

Check the fuel pressure (See page Engine / Hybrid System>1UR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the fuel system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.CHECK FOR SPARKS AND IGNITION

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARKS AND IGNITION
a.

Perform the spark test (See page Engine / Hybrid System>1UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

OK:

Sparks jump across electrode gap.


HINT:

Perform "Inspection After Repair" after repairing or replacing the ignition system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE IGNITION SYSTEM

10.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure (See page Engine / Hybrid System>1UR-FE FUEL>FUEL INJECTOR>INSPECTION).

·

If the injectors malfunction, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count (to Cylinder #8 Misfire Count).

·

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





OK

15.PERFORM CONFIRMATION DRIVING PATTERN

NG

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

23.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY)
13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC is not output B



A

16.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

B

END

16.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm that Throttle Idle Position is ON and check the engine idling condition and the value of MAP in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
Step 0 Step 0 to 30
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least 10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

18.CHECK HARNESS AND CONNECTOR

NG

17.INSPECT EGR VALVE ASSEMBLY
17.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

18.CHECK HARNESS AND CONNECTOR

NG

18.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

19.CHECK WHETHER DTC OUTPUT RECURS
19.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC P0171, P0172, P0174 or P0175 is output A
DTC is not output B



A

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.
U151537E02
1.521,1.531 0.833,1.958 false 1.76,1.521 2.448,1.927 false 1.469,3.865 1.75,4.406 false 1.385,3.865 1.031,4.406 false 0.458,1.396 0.729,1.573 0.271,0.177 10 false D7 0.49,1.875 0.833,2.052 0.344,0.177 10 false E2G 2.5,1.844 2.781,2.083 0.281,0.24 10 false VG 0.125,2.917 0.448,3.094 0.323,0.177 10 false D74 1.667,4.427 2.073,4.625 0.406,0.198 10 false E2G 0.917,4.427 1.135,4.604 0.219,0.177 10 false VG 0.156,0.094 2.49,0.438 2.333,0.344 10 false Front view of wire harness connector: (to MAF Meter) 0.146,2.167 2.479,2.51 2.333,0.344 10 false Front view of wire harness connector: (to ECM)

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-3 (VG) - D74-74 (VG) Always Below 1 Ω
D7-2 (E2G) - D74-75 (E2G) Always Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground Always 10 kΩ or higher




OK

21.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter assembly.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0171, P0172, P0174 or P0175 is output B



A

END

B

23.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY)

OK

24.INSPECT INTEGRATION RELAY (A/F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR