Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  P103D  A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P2195).

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

When one of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.

A164715E02
0.054,0.046 2.664,0.305 2.609,0.259 12 Reference (System Diagram): 5.056,1.219 5.615,1.374 0.559,0.155 10 HA1A 3.965,1.239 4.523,1.394 0.559,0.155 10 HA1A 3.294,1.251 3.533,1.406 0.239,0.156 10 +B 5.056,1.735 5.504,1.900 0.448,0.164 10 A1A+ 3.984,1.775 4.432,1.940 0.448,0.164 10 A1A+ 5.056,2.485 5.541,2.645 0.485,0.160 10 A1A- 3.297,1.764 3.782,1.924 0.485,0.160 10 A1A- 2.258,2.873 3.398,3.043 1.140,0.170 10 from EFI Relay 3.544,1.506 4.017,1.685 0.473,0.179 10 Heater 3.528,2.04 4.001,2.233 0.473,0.193 10 Sensor 2.004,2.357 2.292,2.518 0.288,0.160 10 A/F 1.275,1.521 1.563,1.681 0.288,0.161 10 A/F 3.446,2.366 4.275,2.568 0.829,0.202 10 A/F Sensor 0.265,1.236 0.791,1.623 0.526,0.387 10 from Battery 5.785,2.934 6.232,3.090 0.448,0.156 10 ECM 6.312,1.843 6.825,2.235 0.512,0.392 10 Duty Control



DTC No. DTC Detection Condition Trouble Area
P0031
P0051
Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A
(1 trip detection logic)
·

Open in A/F sensor heater circuit

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

ECM


P0032
P0052
Air-Fuel Ratio (A/F) sensor heater current failure
(1 trip detection logic)
·

Short in A/F sensor heater circuit

·

A/F sensor heater (for Sensor 1)

·

Integration relay

·

ECM


P101D
P103D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Open or short in A/F sensor heater circuit

·

ECM



MONITOR DESCRIPTION

The ECM uses information from the Air-Fuel Ratio (A/F) sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.

The A/F sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The A/F sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the A/F sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.

When the current in the A/F sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Related DTCs P0031: A/F sensor heater (for Bank 1) open/short (Low electrical current)
P0032: A/F sensor heater (for Bank 1) open/short (High electrical current)
P0051: A/F sensor heater (for Bank 2) open/short (Low electrical current)
P0052: A/F sensor heater (for Bank 2) open/short (High electrical current)
P101D: A/F sensor heater (for Bank 1) performance
P103D: A/F sensor heater (for Bank 2) performance
Required Sensors/Components (Main) A/F sensor heater
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 10 seconds: P0031 and P0051
10.24 seconds: P0032 and P0052
1 second: P101D and P103D
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0031 and P0051
Monitor runs whenever following DTCs not stored P101D, P103D (Air fuel ratio sensor heater)
One of following conditions met -
A. All of following conditions met -
Battery voltage 10.5 V or higher
Time after heater on 5 seconds or more
Active heater OFF control Not operating
Active heater ON control Not operating
Air fuel ratio sensor heater duty-cycle 10% or more
B. All of following conditions met -
Output duty cycle 30% or more

P0032 and P0052
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or higher
Time after heater on 5 seconds or more
Active heater OFF control Not operating
Active heater ON control Not operating
Air fuel ratio sensor heater duty-cycle More than 0%

P101D and P103D
Monitor runs whenever following DTCs not stored P0031, P0051 (Air fuel ratio sensor heater)
Battery voltage 10.5 V or higher
Active heater OFF control Not operating
Active heater ON control Not operating

TYPICAL MALFUNCTION THRESHOLDS

P0031 and P0051
Air fuel ratio sensor heater current Below 0.8 A

P0032 and P0052
All of following condition met -
Air fuel ratio sensor heater output ON
Hybrid IC high current limiter monitor Fail

P101D and P103D
All of following condition met -
Air fuel ratio sensor heater OFF current Higher than 11 A
Hybrid IC high current limiter monitor input Fail

COMPONENT OPERATING RANGE

A/F sensor heater current 0.8 A or more

CONFIRMATION DRIVING PATTERN

A198819E21
0.75,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 1.011,1.717 1.417,1.878 0.406,0.161 10 Idling 0.196,2.028 1.442,2.239 1.246,0.211 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.614,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.851,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream ON.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0031, P0032, P0051, P0052, P101D or P103D.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



14.

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

15.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
U151430E02
1.854,1.917 2.313,1.625 false 0.104,0.063 2.427,0.448 2.323,0.385 10 false Front view of wire harness connector: (to A/F Sensor) 2.385,1.521 2.635,1.74 0.25,0.219 10 false +B 0.073,2.646 1.479,2.844 1.406,0.198 10 false *1: for Bank 1 0.073,2.979 1.479,3.177 1.406,0.198 10 false *2: for Bank 2 0.76,2.052 0.99,2.25 0.229,0.198 10 false *2 0.354,2.063 0.667,2.26 0.313,0.198 10 false D34 0.75,1.708 0.958,1.896 0.208,0.188 10 false *1 0.354,1.708 0.625,1.906 0.271,0.198 10 false D33

a.

Disconnect the A/F sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D33-2 (+B) - Body ground Ignition switch ON 11 to 14 V
D34-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Result
Result Proceed to
NG A
OK B



A

3.INSPECT INTEGRATION RELAY (A/F)

B

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
3.INSPECT INTEGRATION RELAY (A/F)
a.

Remove the integration relay from the engine room relay block.


b.

Inspect the A/F fuse.

i.

Remove the A/F fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω



iii.

Reinstall the A/F fuse.



U151425E02
0.104,0.115 2.615,0.479 2.51,0.365 10 false Component without harness connected: (Integration Relay) 0.49,2.417 0.75,2.594 0.26,0.177 10 false 1C 1.365,2.406 1.583,2.583 0.219,0.177 10 false 1B 2.438,2.406 2.688,2.604 0.25,0.198 10 false 1A

c.

Inspect the integration relay (A/F).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1A-4 No battery voltage applied to terminals 1A-2 and 1A-3 10 kΩ or higher
Battery voltage applied to terminals 1A-2 and 1A-3 Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)

NG

REPLACE INTEGRATION RELAY (A/F)

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND)
A379412E01
0.646,1.625 1.031,1.865 0.385,0.24 0.646,1.271 1.031,1.51 0.385,0.24 4.323,0.854 4.656,1.083 0.333,0.229 5.542,0.833 5.875,1.063 0.333,0.229 2.135,1.458 2.615,1.188 false 4.5,1.563 4.875,1.281 false 5.563,1.563 5.302,1.302 false 5.667,1.552 5.479,1.271 false 5.719,1.563 5.969,1.281 false 0.479,0.135 2.792,0.521 2.313,0.385 10 false Front view of wire harness connector: (to A/F Sensor) 0.708,1.302 1.063,1.5 0.354,0.198 10 false D33 0.719,1.656 1.073,1.854 0.354,0.198 10 false D34 1.094,1.302 1.302,1.49 0.208,0.188 10 false *1 1.094,1.646 1.302,1.833 0.208,0.188 10 false *2 2.667,1.094 3,1.302 0.333,0.208 10 false +B 3.729,0.104 6.042,0.49 2.313,0.385 10 false Front view of wire harness connector: (to Integration Relay) 4.906,1.146 5.115,1.333 0.208,0.188 10 false 5 5.177,1.135 5.313,1.323 0.135,0.188 10 false 4 5.417,1.104 5.552,1.281 0.135,0.177 10 false 3 6,1.104 6.135,1.281 0.135,0.177 10 false 2 4.396,0.885 4.688,1.073 0.292,0.188 10 false 1B 5.604,0.865 5.896,1.052 0.292,0.188 10 false 1A 0.24,2.063 1.198,2.25 0.958,0.188 10 false *1: for Bank 1 0.24,2.375 1.198,2.563 0.958,0.188 10 false *2: for Bank 2

a.

Disconnect the A/F sensor connector.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D33-2 (+B) - 1A-4 Always Below 1 Ω
D34-2 (+B) - 1A-4 Always Below 1 Ω
1A-2 - 1B-5 Always Below 1 Ω
1A-3 - Body ground Always Below 1 Ω
D33-2 (+B) or 1A-4 - Body ground Always 10 kΩ or higher
D34-2 (+B) or 1A-4 - Body ground Always 10 kΩ or higher
1A-2 or 1B-5 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A379413E01
0.552,1.104 0.927,1.333 0.375,0.229 0.563,1.375 0.938,1.604 0.375,0.229 3.719,0.854 4.094,1.083 0.375,0.229 1.302,1.823 1.656,1.594 false 5.042,2.24 5.365,1.469 false 5.885,2.229 5.521,1.458 false 0.438,0.135 2.75,0.583 2.313,0.448 10 false Front view of wire harness connector: (to A/F Sensor) 0.615,1.135 0.979,1.333 0.365,0.198 10 false D33 0.615,1.406 0.979,1.604 0.365,0.198 10 false D34 0.979,1.115 1.229,1.281 0.25,0.167 10 false *1 0.99,1.396 1.24,1.563 0.25,0.167 10 false *2 0.719,1.708 1.333,1.885 0.615,0.177 10 false HA1A*1 0.719,1.875 1.333,2.052 0.615,0.177 10 false HA2A*2 3.771,0.104 6.083,0.552 2.313,0.448 10 false Front view of wire harness connector: (to ECM) 3.802,0.896 4.167,1.094 0.365,0.198 10 false D74 4.938,2.271 5.385,2.469 0.448,0.198 10 false HA2A 5.781,2.25 6.229,2.448 0.448,0.198 10 false HA1A 0.094,2.156 1.146,2.354 1.052,0.198 10 false *1: for Bank 1 0.094,2.448 1.146,2.646 1.052,0.198 10 false *2: for Bank 2

a.

Disconnect the A/F sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D33-1 (HA1A) - D74-22 (HA1A) Always Below 1 Ω
D34-1 (HA2A) - D74-20 (HA2A) Always Below 1 Ω
D33-1 (HA1A) or D74-22 (HA1A) - Body ground Always 10 kΩ or higher
D34-1 (HA2A) or D74-20 (HA2A) - Body ground Always 10 kΩ or higher




OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Read the output pending DTCs using the Techstream.

Result
Result Proceed to
No pending DTC is output A
Pending DTC P0031, P0032, P0051, P0052, P101D or P103D is output B



A

B