Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  P0139  Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2)  P013A  Oxygen Sensor Slow Response - Rich to Lean Bank 1 Sensor 2  P013C  Oxygen Sensor Slow Response - Rich to Lean Bank 2 Sensor 2  P0156  Oxygen Sensor Circuit (Bank 2 Sensor 2)  P0157  Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)  P0158  Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)  P0159  Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a Heated Oxygen (HO2) sensor is used.

The HO2 sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel ratio, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the HO2 sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the HO2 sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E07
2.979,1.229 3.292,0.844 false 2.688,1.792 3.302,1.792 true 2.594,2.417 3.25,2.385 true 2.677,2.698 3.26,2.833 false 1.094,2.917 1.333,2.917 false 2.667,1.458 2.667,1.531 false 2.729,1.646 3.302,1.271 3.302,1.271 2.667,1.49 true 1.448,0.771 2.458,0.969 1.01,0.198 10 false Atmospheric Air 3.354,0.74 4.094,0.938 0.74,0.198 10 false Housing 3.365,1.188 4.667,1.406 1.302,0.219 10 false Platinum Electrode 3.958,0.885 4.927,1.083 0.969,0.198 10 false Output Voltage 5.01,0.927 6.396,1.125 1.385,0.198 10 false Ideal Air-fuel Mixture 2.01,3.167 2.906,3.365 0.896,0.198 10 false Exhaust Gas 3.344,1.698 4.521,2.083 1.177,0.385 10 false Solid Electrolyte (Zirconia Element) 3.292,2.76 4.49,2.958 1.198,0.198 10 false Coating (Ceramic) 3.323,2.281 3.802,2.479 0.479,0.198 10 false Heater 1.365,2.823 1.802,3.031 0.438,0.208 10 false Cover 4.792,2.927 7.094,3.125 2.302,0.198 10 false Richer - Air-fuel Ratio - Leaner

DTC No. DTC Detection Condition Trouble Area
P0136
P0156
Either condition is met:
·

Abnormal voltage output:

During active air-fuel ratio control, HO2 sensor voltage does not increase to more than 0.66 V for certain period of time (2 trip detection logic)


·

Low impedance:

Sensor impedance less than 5 Ω for more than 30 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)



·

HO2 sensor (for Bank 1, 2) circuit

·

HO2 sensor (for Bank 1, 2)

·

Air-Fuel Ratio (A/F) sensor (for Bank 1, 2)

·

Integration relay

·

Gas leak from exhaust system

·

EGR valve assembly


P0137
P0157
Either condition is met:
·

Low voltage (open):

During active air-fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic):

(a) HO2 sensor voltage output less than 0.21 V


(b) Target air-fuel ratio rich



·

High impedance:

Sensor impedance 15 kΩ or more for more than 90 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)



·

HO2 sensor (for Bank 1, 2) circuit

·

HO2 sensor (for Bank 1, 2)

·

Air-Fuel Ratio (A/F) sensor (for Bank 1, 2)

·

Integration relay

·

Gas leak from exhaust system

·

EGR valve assembly


P0138
P0158
·

Extremely high voltage (short):

HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)



·

HO2 sensor (for Bank 1, 2) circuit

·

HO2 sensor (for Bank 1, 2)

·

ECM


P0139
P0159
Heated oxygen sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic).
·

HO2 sensor (for Bank 1, 2 Sensor 2) circuit

·

HO2 sensor (for Bank 1, 2 Sensor 2)

·

Gas leak from exhaust system

·

EGR valve assembly

·

ECM


P013A
P013C
Heated oxygen sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection logic).
·

HO2 sensor (for Bank 1, 2 Sensor 2) circuit

·

HO2 sensor (for Bank 1, 2 Sensor 2)

·

Gas leak from exhaust system

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

Active Air-Fuel Ratio Control


The ECM usually performs air-fuel ratio feedback control so that the Air-Fuel Ratio (A/F) sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen (HO2) Sensor (DTC P0136 and P0156)


While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the HO2 sensor voltage does not increase to more than 0.66 V during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

A115540E80
3.573,1.844 3.146,2.073 false 3.573,1.625 3.125,1.375 false 0.115,0.083 5.24,0.313 5.125,0.229 10 false Heated Oxygen Sensor Circuit Malfunction (P0136 and P0156: Abnormal Voltage) 0.313,0.885 1.979,1.083 1.667,0.198 10 false Active air-fuel ratio control 0.333,1.99 1.688,2.177 1.354,0.188 10 false HO2 sensor voltage 2.479,0.875 2.771,1.052 0.292,0.177 10 false Off 2.219,1.646 2.698,1.813 0.479,0.167 10 false 0.66 V 2.219,2.427 2.729,2.573 0.51,0.146 10 false 0.21 V 2.646,1.25 3.208,1.427 0.563,0.177 10 false Normal 2.781,2.073 3.448,2.281 0.667,0.208 10 false Abnormal 4.615,0.5 5.781,0.667 1.167,0.167 10 false 15 to 20 seconds 4.24,0.823 4.979,1.042 0.74,0.219 10 false Operating


Open in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157)


During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean.

If the HO2 sensor has an open, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the HO2 sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

HINT:

*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated, based on the calculated OSC value (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>P0420).


A234468E06
0.066,0.046 3.859,0.255 3.793,0.209 10 HO2 Sensor Circuit Low Voltage (P0137 and P0157: Open) 0.283,1.213 1.175,1.552 0.892,0.339 10 Active air fuel ratio control 0.283,3.203 1.070,3.563 0.788,0.359 10 HO2 sensor voltage 0.283,2.078 1.552,2.280 1.269,0.202 10 Target air fuel ratio 1.974,2.027 2.928,2.395 0.953,0.368 10 Stoichiometric Air Fuel Level 2.783,1.306 3.149,1.508 0.367,0.202 10 OFF 2.492,3.469 2.979,3.671 0.487,0.202 10 0.21 V 4.314,0.729 5.467,0.931 1.153,0.202 10 15 to 20 seconds 4.519,1.274 5.283,1.476 0.764,0.202 10 Operation 4.658,1.636 5.224,1.838 0.565,0.202 10 Normal 5.683,1.616 6.328,1.818 0.646,0.202 10 Abnormal 6.058,4.057 6.794,4.259 0.737,0.202 10 Abnormal 6.055,2.47 6.620,2.672 0.565,0.202 10 Normal 4.782,2.408 5.147,2.610 0.366,0.202 10 Rich 5.815,3.761 6.025,4.024 false 4.292,2.016 4.453,1.724 false 4.453,1.724 4.591,1.724 false 5.342,2.366 5.443,1.715 false 5.443,1.715 5.628,1.715 false 5.693,2.983 5.843,2.554 false 5.843,2.554 6.001,2.554 false


High or Low Impedance of Heated Oxygen (HO2) Sensor (DTC P0136 and P0156 or P0137 and P0157)


A076841E39
1.167,1.229 1.531,0.781 1.531,0.781 0.854,2.49 false 0.115,0.052 2.802,0.406 2.688,0.354 10 false Relationship between element temperature and impedance: 1.573,0.677 2.875,0.875 1.302,0.198 10 false DTC Detection Area 1.385,3.156 1.875,3.354 0.49,0.198 10 false °C (°F) 0.135,0.833 0.375,1.031 0.24,0.198 10 false (Ω) 0.198,1.104 0.635,1.302 0.438,0.198 10 false 15000 0.26,1.49 0.625,1.688 0.365,0.198 10 false 1000 0.333,1.854 0.604,2.052 0.271,0.198 10 false 100 0.438,2.188 0.635,2.385 0.198,0.198 10 false 10 0.49,2.375 0.615,2.573 0.125,0.198 10 false 5 0.531,2.698 0.802,2.896 0.271,0.198 10 false 300 0.469,2.906 0.833,3.104 0.365,0.198 10 false (572) 0.958,2.698 1.229,2.896 0.271,0.198 10 false 400 0.896,2.906 1.26,3.104 0.365,0.198 10 false (752) 1.396,2.698 1.667,2.896 0.271,0.198 10 false 500 1.313,2.906 1.677,3.104 0.365,0.198 10 false (932) 1.885,2.698 2.156,2.896 0.271,0.198 10 false 600 1.74,2.906 2.198,3.104 0.458,0.198 10 false (1112) 2.906,2.698 3.177,2.896 0.271,0.198 10 false 800 2.781,2.906 3.24,3.104 0.458,0.198 10 false (1472) 2.396,2.698 2.667,2.896 0.271,0.198 10 false 700 2.26,2.906 2.719,3.104 0.458,0.198 10 false (1292)

During normal air-fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variation of the HO2 sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.

*: The effective resistance in an alternating current electrical circuit.

HINT:
·

The impedance cannot be measured using an ohmmeter.

·

DTCs P0136 and P0156 indicate the deterioration of the HO2 sensor. The ECM stores the DTCs by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).

·

DTCs P0137 and P0157 indicate an open or short circuit in the HO2 sensor (2 driving cycles). The ECM stores the DTCs when the impedance of the sensor exceeds the threshold 15 kΩ.




Extremely High Output Voltage of Heated Oxygen (HO2) Sensor (DTC P0138 or P0158)


The ECM continuously monitors the HO2 sensor output voltage while the engine is running.

DTC P0138 or P0158 is stored if the HO2 sensor voltage output is more than 1.2 V for 10 seconds or more.


Heated Oxygen Sensor Output Voltage During Fuel Cut (P0139 or P0159)


The sensor output voltage drops to below 0.2 V (extremely lean status) immediately when the vehicle decelerates and fuel cut is operating. If the voltage does not drop to below 0.2 V when accumulated intake air mass is more than 15.3 g, the system determines that the sensor response has deteriorated, illuminates the MIL and stores a DTC.


Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut from Rich Condition (P013A and P013C)


If the sensor output voltage does not drop from 0.35 to 0.2 V immediately when the vehicle decelerates and fuel cut is operating, the ECM illuminates the MIL and stores a DTC.


MONITOR STRATEGY

Related DTCs P0136: Heated oxygen sensor (for Bank 1) output voltage (Abnormal voltage output)
P0136: Heated oxygen sensor (for Bank 1) impedance (Low)
P0137: Heated oxygen sensor (for Bank 1) output voltage (Low voltage)
P0137: Heated oxygen sensor (for Bank 1) impedance (High)
P0138: Heated oxygen sensor (for Bank 1) output voltage (Extremely high)
P0139: Heated oxygen sensor output voltage during fuel cut (for Bank 1)
P013A: Heated oxygen sensor response rate during fuel cut from rich condition
P013C: Heated oxygen sensor response rate during fuel cut from rich condition
P0156: Heated oxygen sensor (for Bank 2) output voltage (Abnormal voltage output)
P0156: Heated oxygen sensor (for Bank 2) impedance (Low)
P0157: Heated oxygen sensor (for Bank 2) output voltage (Low voltage)
P0157: Heated oxygen sensor (for Bank 2) impedance (High)
P0158: Heated oxygen sensor (for Bank 2) output voltage (Extremely high)
P0159: Heated oxygen sensor output voltage during fuel cut (for Bank 2)
Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter, throttle position sensor and air fuel ratio sensor
Frequency of Operation Once per driving cycle: Active air-fuel ratio control detection, heated oxygen sensor abnormal voltage during fuel cut
Continuous: Other
Duration 20 seconds: Active air-fuel ratio control detection
90 seconds: Heated oxygen sensor impedance (High)
30 seconds: Heated oxygen sensor impedance (Low)
10 seconds: Output voltage (Extremely high)
7 seconds: Heated oxygen sensor voltage (During fuel cut)
7 seconds: Heated oxygen sensor response rate during fuel cut from rich condition
MIL Operation 2 driving cycles: P0136, P0137, P0138, P0139, P0156, P0157, P0158 and P0159
1 driving cycles: P013A and P013C
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058, P102D, P105D (Rear oxygen sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0128 (Thermostat)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333 (Knock Sensor)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0401 (EGR system)
P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System)

Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output and Low Voltage)
Active air-fuel ratio control Executing
Active air-fuel ratio control begins when all of following conditions met: -
Battery voltage 11 V or more
Engine coolant temperature 75°C (167°F) or more
Atmospheric pressure 76 kPa(abs) [570 mmHg(abs)] or higher
Idling OFF
Engine RPM Less than 3200 rpm
A/F sensor status Activated
Fuel system status Closed loop
Fuel cut OFF
Engine load 10 to 75%
Transmission gear 4th or higher

Heated Oxygen Sensor Impedance (Low)
Battery voltage 11 V or more
Estimated rear HO2 sensor temperature Less than 700°C (1292°F)
ECM monitor Completed
DTC P0607 Not set

Heated Oxygen Sensor Impedance (High)
Battery voltage 11 V or more
Estimated rear HO2 sensor temperature 450 to 750°C (842 to 1382°F)
ECM monitor Completed
DTC P0607 Not set

Heated Oxygen Sensor Output Voltage (Extremely High)
Battery voltage 11 V or more
Time after engine start 2 seconds or more

Heated Oxygen Sensor Output Voltage During Fuel Cut
Engine coolant temperature 75°C (167°F) or higher
Estimated catalyst temperature 400°C (752°F) or higher
Fuel cut ON

Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Estimated catalyst temperature 400°C (752°F) or higher
Fuel cut ON

TYPICAL MALFUNCTION THRESHOLDS

Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output)
All of following conditions (a), (b) and (c) met -
(a) Commanded air-fuel ratio 14.3 or less
(b) Rear HO2 sensor voltage 0.21 to 0.66 V
(c) OSC (Oxygen Storage Capacity of Catalyst) 2 g or more

Heated Oxygen Sensor Output Voltage (Low Voltage)
All of following conditions (a), (b) and (c) met -
(a) Commanded air-fuel ratio 14.3 or less
(b) Rear HO2 sensor voltage Less than 0.21 V
(c) OSC 2 g or more

Heated Oxygen Sensor Impedance (Low)
Duration following condition met 30 seconds or more
Heated oxygen sensor impedance Less than 5 Ω

Heated Oxygen Sensor Impedance (High)
Duration following condition met 90 seconds or more
Heated oxygen sensor impedance 15 kΩ or more

Heated Oxygen Sensor Output Voltage (Extremely High)
Duration following condition met 10 seconds or more
Heated oxygen sensor voltage 1.2 V or more

Heated Oxygen Sensor Output Voltage During Fuel Cut
Total airflow volume reached after start of fuel-cut while heated oxygen sensor voltage remains at 0.2 V or higher More than 15.3 g

Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition
Duration that heated oxygen sensor voltage drops from 0.35 to 0.2 V during fuel cut (Normalized) 1 second or more

COMPONENT OPERATING RANGE

Duration following condition met 30 seconds or more
Heated oxygen sensor voltage Varies between 0.1 and 0.9 V

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the Heated Oxygen (HO2) sensor monitor (The catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



P0136, P0137, P0138, P0156, P0157 and P0158

A357476E05
0.396,0.469 1.646,0.656 1.25,0.188 10 false 120 km/h (75 mph) 0.5,1.354 1.677,1.542 1.177,0.188 10 false 60 km/h (37 mph) 1.198,2.208 1.677,2.396 0.479,0.188 10 false Idling 0.406,2.479 1.646,2.688 1.24,0.208 10 false Ignition Switch ON 2,2.417 2.271,2.615 0.271,0.198 10 false [A] 2.583,2.073 2.854,2.271 0.271,0.198 10 false [B] 3.938,0.667 4.208,0.865 0.271,0.198 10 false [C] 4.979,3.323 5.25,3.521 0.271,0.198 10 false [D] 2.323,2.917 3.156,3.125 0.833,0.208 10 false Warming up 3.469,2.927 4.76,3.125 1.292,0.198 10 false 10 minutes or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

With the transmission in 4th gear or higher, drive the vehicle at 60 to 120 km/h (37 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D].



13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




P0139, P013A, P013C and P0159

A284467E12
0.189,0.702 1.136,0.858 0.948,0.156 10 Vehicle Speed 0.054,1.174 1.168,1.330 1.114,0.156 10 60 km/h (37 mph) 0.796,2.218 1.174,2.373 0.378,0.156 10 Idling 0.041,2.421 1.168,2.577 1.127,0.156 10 Ignition Switch off 1.473,2.762 2.250,2.945 0.776,0.184 10 Warming up 2.557,2.762 3.796,2.945 1.239,0.184 10 10 minutes or more 1.761,2.116 1.993,2.289 0.232,0.173 10 [A] 3.064,1.037 3.555,1.210 0.492,0.173 10 [B]* 4.213,1.037 4.445,1.210 0.232,0.173 10 [C] 5.203,1.037 5.436,1.210 0.232,0.173 10 [C] 6.184,1.037 6.416,1.210 0.232,0.173 10 [C] 4.707,3.139 4.912,3.312 0.205,0.173 10 [D] 5.708,3.139 5.912,3.312 0.205,0.173 10 [D] 6.697,3.139 6.901,3.312 0.205,0.173 10 [D] 0.049,3.36 4.667,3.567 4.619,0.207 10 *: Drive the vehicle while keeping the engine load as constant as possible.

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

8.

Check that Catalyst Efficiency / Current is Incomplete.

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

10.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


11.

Drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].

13.

Check the Test Value for RL F/C B1S2, RL F/C B2S2.

HINT:

If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.


14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

15.

Read the pending DTC [D].

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P0139, P013A, P013C or P0159.

18.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows INCOMPLETE or N/A, drive the vehicle with the shift lever in S, and then perform step [C] again.



19.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A167571E01
5.986,0.535 6.378,0.691 0.392,0.156 10 HT1B 5.986,3.169 6.378,3.325 0.392,0.156 10 HT2B 4.172,3.169 4.564,3.325 0.392,0.156 10 HT2B 5.661,0.623 5.942,0.779 0.281,0.156 10 D74 5.661,1.408 5.942,1.564 0.281,0.156 10 D74 5.661,2.673 5.942,2.829 0.281,0.156 10 D74 5.661,3.257 5.942,3.413 0.281,0.156 10 D74 5.661,4.042 5.942,4.198 0.281,0.156 10 D74 5.661,5.225 5.942,5.380 0.281,0.156 10 D74 5.661,5.67 5.942,5.826 0.281,0.156 10 A24 5.99,1.398 6.396,1.554 0.406,0.156 10 OX1B 4.409,1.244 4.815,1.400 0.406,0.156 10 OX1B 5.99,4.032 6.396,4.188 0.406,0.156 10 OX2B 4.155,3.878 4.561,4.034 0.406,0.156 10 OX2B 6.004,2.672 6.396,2.828 0.392,0.156 10 EX1B 5.992,5.223 6.384,5.379 0.392,0.156 10 EX2B 6,5.588 6.420,5.744 0.420,0.156 10 MREL 6.29,5.985 6.637,6.141 0.347,0.156 10 ECM 5.706,0.451 5.890,0.614 0.184,0.163 10 45 5.664,1.243 5.917,1.399 0.253,0.156 10 114 5.664,2.508 5.931,2.678 0.267,0.170 10 115 5.706,3.099 5.904,3.255 0.198,0.156 10 44 5.67,3.874 5.947,4.033 0.277,0.159 10 112 5.67,5.056 5.947,5.216 0.277,0.159 10 113 5.706,5.504 5.890,5.660 0.184,0.156 10 34 3.843,1.731 4.138,1.887 0.295,0.156 10 D31 3.843,1.885 5.070,2.216 1.227,0.332 10 Heated Oxygen Sensor (for Bank 1) 3.28,4.292 3.575,4.448 0.295,0.156 10 D32 3.28,4.425 4.518,4.757 1.239,0.333 10 Heated Oxygen Sensor (for Bank 2) 4.852,0.529 4.967,0.685 0.114,0.156 10 1 3.832,0.525 3.946,0.680 0.114,0.156 10 2 4.851,1.306 4.977,1.457 0.126,0.151 10 3 3.829,1.306 3.957,1.462 0.128,0.156 10 4 4.614,3.177 4.728,3.333 0.114,0.156 10 1 3.594,3.173 3.708,3.328 0.114,0.156 10 2 4.613,3.954 4.739,4.105 0.126,0.151 10 3 3.59,3.954 3.719,4.109 0.128,0.156 10 4 4.011,0.535 4.208,0.691 0.198,0.156 10 +B 3.773,3.169 3.970,3.325 0.198,0.156 10 +B 4.415,0.521 4.807,0.677 0.392,0.156 10 HT1B 4.004,1.292 4.201,1.448 0.198,0.156 10 E1 3.78,3.94 3.977,4.095 0.198,0.156 10 E1 0.13,6.422 0.866,6.592 0.737,0.170 10 *: Shielded 2.806,0.745 3.462,0.901 0.656,0.156 10 EFI NO. 2 1.503,1.675 2.589,1.858 1.086,0.184 10 Integration Relay 1.7,0.311 1.953,0.467 0.253,0.156 10 EFI 0.787,0.75 1.429,0.920 0.642,0.170 10 EFI NO. 1 2.35,0.451 2.465,0.607 0.114,0.156 10 4 2.35,0.885 2.465,1.041 0.114,0.156 10 2 1.104,1.488 1.218,1.644 0.114,0.156 10 3 0.543,0.451 0.657,0.607 0.114,0.156 10 1 2.305,0.623 2.517,0.779 0.211,0.156 10 1B 2.305,1.057 2.517,1.213 0.211,0.156 10 1B 1.295,1.478 1.507,1.634 0.211,0.156 10 1B 0.494,0.623 0.706,0.779 0.211,0.156 10 1C 0.578,5.31 1.060,5.487 0.482,0.177 10 Battery 4.861,5.388 4.987,5.525 0.126,0.137 10 * 5.26,2.936 5.386,3.073 0.126,0.137 10 *

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.

1.

Connect the Techstream to the DLC3.

2.

Start the engine and turn the Techstream on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the A/F and HO2 sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.



HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
+12.5% Rich Higher than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5% Lean Below 0.4 V

NOTICE:

The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.


A283583E56
5.813,3.708 7.135,3.979 1.323,0.271 10 false - A/F sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.563,4.875 1.052,0.177 8 false Higher than 0.55 V 0.917,2.646 1.885,2.813 0.969,0.167 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.469,1.604 1.917,1.792 0.448,0.188 8 false +12.5% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.479,2.604 4.563,2.792 1.083,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.906,6.938 0.99,0.167 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.542 0.49,0.771 0.375,0.229 10 false Case 0.677,0.542 3,0.76 2.323,0.219 10 false A/F Sensor (Sensor 1) Output Voltage 3.24,0.542 5.688,0.781 2.448,0.24 10 false HO2 Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.813,4.063 7.104,4.271 1.292,0.208 10 false - A/F sensor heater 5.813,4.448 7.073,4.646 1.26,0.198 10 false - A/F sensor circuit 5.802,5.813 6.854,6.188 1.052,0.375 10 false - HO2 sensor 5.792,6.198 7.104,6.406 1.313,0.208 10 false - HO2 sensor heater 5.802,6.604 7.104,6.802 1.302,0.198 10 false - HO2 sensor circuit 5.833,7.51 6.677,7.698 0.844,0.188 10 false - Injector 5.833,7.823 6.99,8.156 1.156,0.333 10 false - Fuel pressure 5.813,8.156 7.104,9.01 1.292,0.854 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.417,3.677 1.865,3.865 0.448,0.188 8 false +12.5% 4,1.594 4.448,1.781 0.448,0.188 8 false +12.5% 4.01,3.667 4.458,3.854 0.448,0.188 8 false +12.5% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.385,5.75 1.833,5.938 0.448,0.188 8 false +12.5% 1.375,7.771 1.823,7.958 0.448,0.188 8 false +12.5% 4.01,7.781 4.458,7.969 0.448,0.188 8 false +12.5% 4.063,5.729 4.51,5.917 0.448,0.188 8 false +12.5% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

HINT:
·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be set.

·

If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0156 will be set.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0138 or P0158 is output A
P0137 or P0157 is output B
P0136 or P0156 is output C
P0139, P013A, P013C or P0159 is output D
P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output E



A

2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

8.CHECK FOR EXHAUST GAS LEAK

C

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

21.CHECK FOR EXHAUST GAS LEAK

E

2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
A117841E29
0.094,0.063 2.593,0.413 2.498,0.350 10 Component without harness connected: (HO2 Sensor) 0.865,1.123 1.090,1.278 0.225,0.156 10 +B 2.506,1.105 3.023,1.261 0.517,0.156 10 HT1B*1 2.506,1.346 3.023,1.502 0.517,0.156 10 HT2B*2 2.506,1.913 3.065,2.069 0.559,0.156 10 OX1B*1 2.506,2.154 3.065,2.310 0.559,0.156 10 OX2B*2 0.873,2.151 1.081,2.310 0.208,0.159 10 E1 1.123,1.208 1.414,1.479 false 1.405,1.88 1.109,2.242 false 2.042,1.466 2.438,1.312 false 2.025,1.896 2.485,2.136 false 0.212,2.675 1.576,2.845 1.364,0.170 10 *1: for Bank 1 0.212,3.005 1.576,3.175 1.364,0.170 10 *2: for Bank 2

a.

Disconnect the HO2 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 3 (OX1B) Always 10 kΩ or higher
2 (+B) - 3 (OX2B) Always 10 kΩ or higher
2 (+B) - 4 (E1) Always 10 kΩ or higher


HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
U151413E02
0.385,2.646 0.708,2.135 false 1.01,3.073 0.854,2.125 false 1.823,3.063 2.323,1.708 false 2.604,2.646 2.417,1.708 false 0.156,0.042 2.49,0.406 2.333,0.365 10 false Front view of wire harness connector: (to ECM) 0.198,2.656 0.604,2.844 0.406,0.188 10 false OX2B 0.833,3.073 1.24,3.26 0.406,0.188 10 false OX1B 1.646,3.073 2.042,3.229 0.396,0.156 10 false HT2B 2.448,2.677 2.844,2.833 0.396,0.156 10 false HT1B 0.208,0.958 0.51,1.125 0.302,0.167 10 false D74

a.

Turn the ignition switch off and wait for 5 minutes.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-45 (HT1B) - D74-114 (OX1B) Always 10 kΩ or higher
D74-44 (HT2B) - D74-112 (OX2B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / O2S B1S2 or O2S B2S2.


f.

Change the fuel injection volume using the Techstream, monitoring the voltage output of the HO2 sensors displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard voltage:

Fluctuates between 0.4 V or less and 0.55 V or more.




OK

5.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME FOR A/F SENSOR)

NG

8.CHECK FOR EXHAUST GAS LEAK
5.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Start the engine.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Change the fuel injection volume using the Techstream, and monitor the voltage output of the Air-Fuel Ratio (A/F) and HO2 sensors displayed on the Techstream.


HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The A/F sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the HO2 sensor is displayed as O2S B1S2 or O2S B2S2 on the Techstream.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

Result
Techstream Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
Alternates between more and less than 3.3 V OK
Remains at more than 3.3 V NG
Remains at less than 3.3 V NG

HINT:

A normal HO2 sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the A/F sensor voltage remains at either less or more than 3.3 V despite the HO2 sensor indicating a normal reaction, the A/F sensor is malfunctioning.


A121606E69
5.896,2.469 6.375,1.396 false 5.573,2.271 6.365,1.406 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.354,2.073 4.094,1.688 false 3.583,2.594 3.198,2.917 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 false 3.3 V 2.656,0.26 3.271,0.438 0.615,0.177 10 false +12.5 % 4.125,1.125 4.708,1.323 0.583,0.198 10 false -12.5 % 1.656,2.854 1.906,3.052 0.25,0.198 10 false 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 false 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 false Malfunction 5.865,2.646 6.594,2.813 0.729,0.167 10 false Malfunction 4.76,0.125 5.823,0.323 1.063,0.198 10 false Injection Volume 3.635,2.51 4.969,2.729 1.333,0.219 10 false HO2 Sensor Output 6.354,1.052 7.104,1.448 0.75,0.396 10 false A/F Sensor Output 4.417,2 4.906,2.167 0.49,0.167 10 false Normal




OK

6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

NG

16.REPLACE AIR FUEL RATIO SENSOR
6.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed




OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR ASSEMBLY, FUEL PRESSURE, GAS LEAK FROM SYSTEM)

NG

7.INSPECT EGR VALVE ASSEMBLY
7.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repairs" after replacing the EGR valve assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR ASSEMBLY, FUEL PRESSURE, GAS LEAK FROM SYSTEM)

NG

8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A379418E01
0.323,1.24 0.729,1.458 0.406,0.219 0.323,1.51 0.729,1.729 0.406,0.219 3.594,0.844 4,1.063 0.406,0.219 1.896,1.354 1.438,0.979 false 1.854,1.708 1.51,1.854 false 2.729,1.219 2.302,1.427 false 2.771,1.865 2.292,1.698 false 5.792,1 5.396,1.531 false 5,0.99 5.323,1.521 false 3.979,1.865 3.677,2.219 false 4.052,1.865 4.115,2.188 false 4.125,1.865 4.365,2.188 false 4.208,1.865 4.885,2.188 false 0.375,0.073 2.75,0.49 2.375,0.417 10 false Front view of wire harness connector: (to HO2 Sensor) 3.729,0.094 6.104,0.51 2.375,0.417 10 false Front view of wire harness connector: (to ECM) 0.927,0.885 1.5,1.052 0.573,0.167 10 false HT1B*1 0.917,1.052 1.49,1.219 0.573,0.167 10 false HT2B*2 0.979,1.771 1.552,1.938 0.573,0.167 10 false OX1B*1 0.969,1.938 1.542,2.104 0.573,0.167 10 false OX2B*2 0.396,1.271 0.771,1.448 0.375,0.177 10 false D31 0.771,1.271 1,1.438 0.229,0.167 10 false *1 0.396,1.531 0.771,1.708 0.375,0.177 10 false D32 0.781,1.521 1.01,1.688 0.229,0.167 10 false *2 2.781,1.115 3.063,1.292 0.281,0.177 10 false +B 2.813,1.781 3.094,1.958 0.281,0.177 10 false E1 3.677,0.875 4.052,1.052 0.375,0.177 10 false D74 4.719,0.813 5.125,0.99 0.406,0.177 10 false HT2B 5.677,0.823 6.083,1 0.406,0.177 10 false HT1B 3.479,2.219 3.885,2.396 0.406,0.177 10 false OX2B 3.906,2.219 4.313,2.396 0.406,0.177 10 false EX2B 4.302,2.208 4.708,2.385 0.406,0.177 10 false OX1B 4.813,2.208 5.219,2.385 0.406,0.177 10 false EX1B 0.156,2.146 1.146,2.344 0.99,0.198 10 false *1: for Bank 1 0.156,2.427 1.146,2.625 0.99,0.198 10 false *2: for Bank 2

a.

Disconnect the HO2 sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D31-1 (HT1B) - D74-45 (HT1B) Always Below 1 Ω
D31-3 (OX1B) - D74-114 (OX1B) Always Below 1 Ω
D31-4 (E1) - D74-115 (EX1B) Always Below 1 Ω
D32-1 (HT2B) - D74-44 (HT2B) Always Below 1 Ω
D32-3 (OX2B) - D74-112 (OX2B) Always Below 1 Ω
D32-4 (E1) - D74-113 (EX2B) Always Below 1 Ω
D31-1 (HT1B) or D74-45 (HT1B) - Body ground Always 10 kΩ or higher
D31-3 (OX1B) or D74-114 (OX1B) - Body ground Always 10 kΩ or higher
D32-1 (HT2B) or D74-44 (HT2B) - Body ground Always 10 kΩ or higher
D32-3 (OX2B) or D74-112 (OX2B) - Body ground Always 10 kΩ or higher




OK

11.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

12.PERFORM CONFIRMATION DRIVING PATTERN
12.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


d.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


e.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output)
A
NORMAL
(DTC is not output)
B



A

14.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

B

END

14.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

15.INSPECT EGR VALVE ASSEMBLY
15.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

16.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

17.PERFORM CONFIRMATION DRIVING PATTERN
17.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


d.

Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.


e.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output)
A
NORMAL
(DTC is not output)
B



A

19.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

B

END

19.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

20.INSPECT EGR VALVE ASSEMBLY
20.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

21.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

22.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

22.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
U151413E02
0.385,2.646 0.708,2.135 false 1.01,3.073 0.854,2.125 false 1.823,3.063 2.323,1.708 false 2.604,2.646 2.417,1.708 false 0.156,0.042 2.49,0.406 2.333,0.365 10 false Front view of wire harness connector: (to ECM) 0.198,2.656 0.604,2.844 0.406,0.188 10 false OX2B 0.833,3.073 1.24,3.26 0.406,0.188 10 false OX1B 1.646,3.073 2.042,3.229 0.396,0.156 10 false HT2B 2.448,2.677 2.844,2.833 0.396,0.156 10 false HT1B 0.208,0.958 0.51,1.125 0.302,0.167 10 false D74

a.

Turn the ignition switch off and wait for 5 minutes.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D74-45 (HT1B) - D74-114 (OX1B) Always 10 kΩ or higher
D74-44 (HT2B) - D74-112 (OX2B) Always 10 kΩ or higher




OK

23.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the Confirmation Driving Pattern (P0139, P013A, P013C and P0159).



NEXT

24.READ DTC OUTPUT (DTC P0139, P013A, P013C OR P0159 IS OUTPUTAGAIN)
24.READ DTC OUTPUT (DTC P0139, P013A, P013C OR P0159 IS OUTPUTAGAIN)
a.

Connect the Techstream to the DLC3.


b.

Turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


d.

Input DTCs: P0139, P013A, P013C or P0159.


e.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern increasing the vehicle speed.

Result
Result Proceed to
ABNORMAL
(DTC P0139, P013A, P013C or P0159 is output)
A
NORMAL
(DTC is not output)
B



A

25.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)

B

25.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
a.

Connect the Techstream to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in P or N.

·

The A/C switch and all accessory switches should be off.




c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.


e.

Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.



OK:

MAP and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

26.INSPECT EGR VALVE ASSEMBLY
26.INSPECT EGR VALVE ASSEMBLY
a.

Remove the EGR valve assembly (See page Engine / Hybrid System>1UR-FE EMISSION CONTROL>EGR VALVE>REMOVAL).


b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly or heated oxygen sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG