Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E11
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.533,0.776 0.420,0.177 10 Pulse 5.039,0.599 5.441,0.776 0.402,0.177 10 Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(2 trip detection logic)
·

Open or short in speed signal circuit

·

Wheel speed sensor

·

Combination meter

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Related DTCs P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main) Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU
Required Sensors/Components (Related) Park/Neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor, Throttle Position (TP) sensor and Mass Air Flow (MAF) meter
Frequency of Operation Continuous
Duration 5 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Time after ignition switch off to ON 3 seconds or more
Vehicle speed 9 km/h (5.59 mph) or more
Battery voltage 8 V or more
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No pulse input

CONFIRMATION DRIVING PATTERN

A198825E01
0.657,0.826 1.855,1.052 1.198,0.225 10 24 km/h (15 mph) 1.421,1.996 1.820,2.166 0.399,0.170 10 Idling 0.629,2.346 1.827,2.523 1.198,0.177 10 Ignition Switch ON 2.387,2.221 2.620,2.390 0.232,0.169 10 [A] 4.706,0.42 4.911,0.590 0.205,0.170 10 [B] 6.249,3.234 6.447,3.432 0.198,0.198 10 [C] 3.72,2.965 5.636,3.110 1.916,0.145 10 Total of 30 seconds or more

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


14.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A238382E14
5.166,2.94 6.146,3.096 0.980,0.156 10 to Other ECUs 5.348,2.212 5.699,2.367 0.350,0.156 10 ECM 5.979,0.863 6.232,1.033 0.253,0.170 10 5 V 5.224,1.428 5.547,1.584 0.323,0.156 10 SPD 5.36,2.076 5.641,2.232 0.281,0.156 10 A24 5.001,1.194 5.185,1.346 0.184,0.152 10 13 2.458,2.095 2.725,2.244 0.267,0.149 10 J28 2.444,2.239 3.663,2.402 1.218,0.163 10 Combination Meter 3.651,1.196 3.855,1.352 0.205,0.156 10 +S 3.91,1.198 4.227,1.475 0.317,0.276 10 29 1.18,1.381 1.473,1.530 0.292,0.149 10 SP1 2.404,1.283 2.567,1.432 0.163,0.149 10 SI 1.553,1.287 1.667,1.440 0.114,0.152 10 3 2.141,1.259 2.374,1.454 0.232,0.195 10 30 0.462,2.197 1.903,2.573 1.441,0.376 10 Skid Control ECU (VSC Actuator) 0.483,2.053 0.782,2.202 0.299,0.149 10 A17

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING TECHSTREAM (VEHICLE SPEED)

NG

2.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the Techstream.

OK:

Vehicle speeds displayed on the Techstream and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
U151409E02
1.823,3.375 2.083,4.229 false 1.698,2.188 1.5,1.771 false 0.135,0.073 2.49,0.448 2.354,0.375 10 false Front view of wire harness connector: (to Combination Meter) 0.156,2.365 2.51,2.719 2.354,0.354 10 false Front view of wire harness connector: (to ECM) 1.75,2.135 2.021,2.313 0.271,0.177 10 false +S 1.958,4.271 2.333,4.438 0.375,0.167 10 false SPD 0.302,1.104 0.594,1.281 0.292,0.177 10 false J28 0.24,3.5 0.552,3.708 0.313,0.208 10 false A24

a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J28-29 (+S) - A24-13 (SPD) Always Below 1 Ω
J28-29 (+S) or A24-13 (SPD) - Body ground Always 10 kΩ or higher


HINT:

If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. the tire pressure warning system, audio system, etc.).




OK

4.INSPECT COMBINATION METER ASSEMBLY (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEMS RELATED TO SPEED SIGNAL)

4.INSPECT COMBINATION METER ASSEMBLY (+S VOLTAGE)
U151408E01
0.052,0.009 2.411,0.358 2.359,0.349 10 Front view of wire harness connector: (to Combination Meter) 1.587,1.856 1.803,2.007 0.216,0.151 10 +S 1.543,1.495 1.654,1.836 false 0.189,0.868 0.461,1.049 0.272,0.181 10 J28

a.

Disconnect the combination meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J28-29 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V



HINT:

A voltage of 5 or 12 V is output from each ECU and then input to the combination meter assembly.



OK

5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)

NG

5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
U151838E02
1.854,1.458 2.365,2.115 false 0.458,0.125 2.781,0.49 2.323,0.365 10 false Component with harness connected: (Combination Meter) 0.208,1.219 0.531,1.427 0.323,0.208 10 false J28 0.302,2.677 0.938,2.865 0.635,0.188 10 false 5 to 12 V 0.302,4.094 0.604,4.281 0.302,0.188 10 false 0 V 2.323,4.229 3.313,4.448 0.99,0.219 10 false Wheel Turning 2.417,2.063 2.719,2.25 0.302,0.188 10 false +S

a.

Move the shift lever to N.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J28-29 (+S) - Body ground
·

Ignition switch ON

·

Wheel is turned slowly


Voltage generated intermittently


HINT:
·

The output voltage should fluctuate up and down similarly to the diagram when the wheel is turned slowly.

·

A voltage of 5 or 12 V is output from each ECU and then input to the combination meter assembly.





OK

NG

6.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
U151839E02
1.76,1.448 2.365,2.104 false 0.49,0.104 2.792,0.479 2.302,0.375 10 false Component with harness connected: (Combination Meter) 0.208,1.229 0.573,1.448 0.365,0.219 10 false J28 0.302,2.677 0.938,2.865 0.635,0.188 10 false 5 to 12 V 0.323,4.094 0.625,4.281 0.302,0.188 10 false 0 V 2.323,4.229 3.302,4.417 0.979,0.188 10 false Wheel Turning 2.417,2.063 2.719,2.25 0.302,0.188 10 false SI

a.

Move the shift lever to the neutral position.


b.

Jack up the vehicle.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J28-30 (SI) - Body ground
·

Ignition switch ON

·

Wheel is turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - VSC ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - VSC ACTUATOR ASSEMBLY)
U151712E02
2.521,3.563 2.656,4.344 false 2.344,0.844 1.635,1.75 false 0.198,0.042 2.552,0.396 2.354,0.354 10 false Front view of wire harness connector: (to Combination Meter) 0.24,2.146 2.594,2.5 2.354,0.354 10 false Front view of wire harness connector: (to Skid Control ECU) 2.385,0.75 2.719,0.917 0.333,0.167 10 false SI 2.604,4.344 2.958,4.51 0.354,0.167 10 false SP1 1.604,0.906 1.896,1.083 0.292,0.177 10 false J28 1.594,3.031 1.906,3.208 0.313,0.177 10 false A17

a.

Disconnect the combination meter connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J28-30 (SI) - A17-3 (SP1) Always Below 1 Ω
J28-30 (SI) or A17-3 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE VSC ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR