Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A379702E01
4.354,1.031 6.25,1.219 1.896,0.188 10 false 5 V Constant Voltage Circuit 5.365,1.875 6.385,2.063 1.021,0.188 10 false Microprocessor 2.917,0.865 3.385,1.063 0.469,0.198 10 false BATT 3,1.208 3.302,1.406 0.302,0.198 10 false +B 3.135,2.146 3.438,2.344 0.302,0.198 10 false VC 4.958,3.229 5.427,3.427 0.469,0.198 10 false ECM 4.073,3.01 4.271,3.208 0.198,0.198 10 false R 1.24,0.99 2.573,1.208 1.333,0.219 10 false from EFI NO. 1 Fuse 1.573,1.313 2.573,1.521 1,0.208 10 false from EFI Relay 0.208,1.906 2.667,2.438 2.458,0.531 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.188,2.854 2.635,3.385 2.448,0.531 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A167493E02
5.664,0.877 6.077,1.033 0.413,0.156 10 VCV2 5.39,0.916 5.573,1.058 0.184,0.142 10 66 5.676,1.409 5.994,1.565 0.318,0.156 10 NE+ 5.358,1.319 5.611,1.461 0.253,0.142 10 110 5.358,1.739 5.611,1.881 0.253,0.142 10 111 5.676,1.812 5.971,1.968 0.295,0.156 10 NE- 5.393,2.437 5.584,2.579 0.191,0.142 10 90 5.685,2.528 5.980,2.684 0.295,0.156 10 G2 5.393,2.86 5.584,3.002 0.191,0.142 10 89 5.685,2.944 5.980,3.100 0.295,0.156 10 G2- 5.393,3.577 5.584,3.719 0.191,0.142 10 92 5.685,3.671 6.084,3.827 0.399,0.156 10 VV1+ 5.393,3.995 5.584,4.137 0.191,0.142 10 91 5.685,4.09 6.084,4.245 0.399,0.156 10 VV1- 5.393,4.687 5.584,4.829 0.191,0.142 10 69 5.68,4.782 6.079,4.938 0.399,0.156 10 EV1+ 5.393,5.105 5.584,5.247 0.191,0.142 10 68 5.68,5.2 6.079,5.356 0.399,0.156 10 EV1- 6.067,0.211 6.403,0.362 0.336,0.151 10 ECM 2.924,0.909 3.034,1.065 0.110,0.156 10 3 2.924,1.325 3.034,1.481 0.110,0.156 10 1 2.927,1.732 3.046,1.896 0.119,0.164 10 2 0.222,0.972 0.438,1.124 0.216,0.151 10 D3 0.222,1.116 1.966,1.290 1.744,0.174 10 Crankshaft Position Sensor 0.217,2.3 0.433,2.452 0.216,0.151 10 D6 0.217,2.45 1.863,2.601 1.647,0.151 10 Camshaft Position Sensor 2.601,2.323 2.826,2.479 0.225,0.156 10 VC 2.609,0.994 2.834,1.150 0.225,0.156 10 VC 2.605,2.529 2.826,2.685 0.220,0.156 10 G2 2.633,2.952 2.845,3.118 0.211,0.165 10 G- 2.911,2.238 3.016,2.389 0.105,0.151 10 3 2.911,2.448 3.016,2.599 0.105,0.151 10 1 2.911,2.871 3.016,3.022 0.105,0.151 10 2 2.605,3.457 2.830,3.613 0.225,0.156 10 VC 2.441,3.664 2.828,3.820 0.387,0.156 10 VVL+ 2.483,4.071 2.851,4.236 0.369,0.165 10 VVL- 2.915,3.368 3.020,3.519 0.105,0.151 10 3 2.915,3.578 3.020,3.729 0.105,0.151 10 1 2.915,4.001 3.020,4.152 0.105,0.151 10 2 0.208,3.424 0.498,3.580 0.290,0.156 10 D37 0.208,3.569 1.971,3.896 1.762,0.327 10 VVT Sensor (for Intake Side of Bank 1) 2.52,4.571 2.833,4.727 0.313,0.156 10 VC2 2.525,4.778 2.833,4.933 0.308,0.156 10 EX+ 2.548,5.2 2.852,5.366 0.304,0.165 10 EX- 2.911,4.478 3.016,4.629 0.105,0.151 10 3 2.911,4.688 3.016,4.839 0.105,0.151 10 1 2.911,5.111 3.016,5.262 0.105,0.151 10 2 0.208,4.534 0.498,4.690 0.290,0.156 10 D40 0.208,4.679 2.100,5.006 1.892,0.327 10 VVT Sensor (for Exhaust Side of Bank 1) 6.073,0.053 6.361,0.216 0.288,0.163 10 D74 2.517,1.408 2.846,1.571 0.330,0.163 10 NE+ 2.517,1.828 2.846,1.991 0.330,0.163 10 NE- 5.678,5.918 6.049,6.074 0.371,0.156 10 VV2+ 5.678,6.324 6.049,6.480 0.371,0.156 10 VV2- 5.407,5.839 5.583,5.992 0.177,0.152 10 87 5.407,6.235 5.583,6.388 0.177,0.152 10 88 5.674,7.057 6.046,7.213 0.371,0.156 10 EV2+ 5.674,7.479 6.046,7.635 0.371,0.156 10 EV2- 5.403,6.978 5.579,7.130 0.177,0.152 10 64 5.403,7.39 5.579,7.542 0.177,0.152 10 65 0.218,5.68 0.522,5.845 0.304,0.165 10 D39 0.218,5.83 1.989,6.175 1.772,0.346 10 VVT Sensor (for Intake Side of Bank 2) 2.601,5.709 2.826,5.865 0.225,0.156 10 VC 2.416,5.923 2.822,6.079 0.406,0.156 10 VVR+ 2.416,6.322 2.822,6.478 0.406,0.156 10 VVR- 2.912,5.625 3.031,5.781 0.119,0.156 10 3 2.912,5.83 3.031,5.986 0.119,0.156 10 1 2.912,6.237 3.031,6.393 0.119,0.156 10 2 0.218,6.801 0.522,6.966 0.304,0.165 10 D41 0.218,6.95 2.104,7.296 1.887,0.346 10 VVT Sensor (for Exhaust Side of Bank 2) 2.51,6.846 2.825,7.002 0.315,0.156 10 VC2 2.51,7.064 2.823,7.220 0.313,0.156 10 EX+ 2.533,7.459 2.823,7.615 0.290,0.156 10 EX- 2.912,6.746 3.031,6.902 0.119,0.156 10 3 2.912,6.951 3.031,7.107 0.119,0.156 10 1 2.912,7.366 3.031,7.522 0.119,0.156 10 2

A167494E09
5.655,0.832 6.068,0.987 0.413,0.156 10 VCV1 5.341,0.94 5.622,1.096 0.281,0.156 10 D74 5.381,0.783 5.565,0.925 0.184,0.142 10 67 5.651,1.294 5.915,1.450 0.264,0.156 10 AIP 5.337,1.298 5.618,1.454 0.281,0.156 10 A24 5.377,1.14 5.561,1.282 0.184,0.142 10 54 5.651,1.563 6.064,1.719 0.413,0.156 10 ETHA 5.337,1.671 5.618,1.827 0.281,0.156 10 D74 5.377,1.514 5.561,1.656 0.184,0.142 10 98 5.659,2.414 5.994,2.570 0.335,0.156 10 AIP2 5.345,2.418 5.626,2.573 0.281,0.156 10 A24 5.385,2.26 5.568,2.402 0.184,0.142 10 53 5.659,2.726 6.117,2.882 0.458,0.156 10 ETHW 5.345,2.628 5.626,2.784 0.281,0.156 10 D74 5.345,3.343 5.626,3.499 0.281,0.156 10 D74 5.345,4.466 5.626,4.622 0.281,0.156 10 D74 5.385,2.782 5.568,2.924 0.184,0.142 10 97 0.207,0.905 0.507,1.061 0.299,0.156 10 D58 0.207,1.045 2.187,1.224 1.980,0.179 10 Air Switching Valve (for Bank 1) 0.207,2.182 0.507,2.338 0.299,0.156 10 D59 0.207,2.322 2.187,2.501 1.980,0.179 10 Air Switching Valve (for Bank 2) 2.608,0.938 2.833,1.094 0.225,0.156 10 VC 2.915,0.85 3.025,1.005 0.110,0.156 10 2 2.915,1.2 3.025,1.356 0.110,0.156 10 3 2.576,1.288 2.843,1.444 0.267,0.156 10 AIP 2.631,1.665 2.833,1.821 0.202,0.156 10 E2 2.911,1.58 3.030,1.743 0.119,0.164 10 4 2.526,2.21 2.828,2.366 0.302,0.156 10 VC2 2.915,2.121 3.025,2.277 0.110,0.156 10 2 2.915,2.326 3.025,2.482 0.110,0.156 10 3 2.497,2.414 2.843,2.570 0.346,0.156 10 AIP2 2.558,2.624 2.829,2.780 0.271,0.156 10 E22 2.911,2.539 3.030,2.703 0.119,0.164 10 4 5.656,3.329 5.961,3.485 0.305,0.156 10 PSP 5.381,3.193 5.561,3.342 0.180,0.149 10 72 5.675,4.454 6.105,4.603 0.430,0.149 10 PPMP 5.35,4.309 5.600,4.465 0.250,0.156 10 121 0.214,3.117 0.509,3.273 0.295,0.156 10 D46 0.214,3.266 1.407,3.594 1.193,0.327 10 Power Steering Oil Pressure Sensor 2.614,3.131 2.839,3.296 0.225,0.165 10 VC 2.521,3.334 2.830,3.490 0.309,0.156 10 PSP 2.629,3.707 2.841,3.863 0.211,0.156 10 E2 2.907,3.047 3.016,3.203 0.110,0.156 10 1 2.903,3.25 3.012,3.406 0.110,0.156 10 2 2.903,3.624 3.012,3.780 0.110,0.156 10 3 0.208,4.211 0.660,4.376 0.452,0.165 10 R12 0.208,4.359 1.841,4.533 1.633,0.174 10 Canister Pressure Sensor 2.498,4.25 2.839,4.406 0.341,0.156 10 VCC 2.405,4.459 2.829,4.625 0.424,0.165 10 VOUT 2.395,4.825 2.838,4.990 0.443,0.165 10 SGND 2.899,4.17 3.018,4.326 0.119,0.156 10 6 2.899,4.38 3.018,4.536 0.119,0.156 10 7 2.899,4.741 3.018,4.897 0.119,0.156 10 8 5.202,0.364 5.580,0.557 0.378,0.193 10 ECM

A165789E25
6.096,5.174 6.443,5.329 0.347,0.155 10 ECM 5.385,0.866 5.576,1.022 0.191,0.156 10 80 5.644,0.931 6.043,1.087 0.399,0.156 10 VCTA 5.34,1.017 5.617,1.162 0.277,0.145 10 D74 5.385,1.233 5.576,1.389 0.191,0.156 10 78 5.34,1.385 5.617,1.530 0.277,0.145 10 D74 5.385,1.601 5.576,1.757 0.191,0.156 10 77 5.34,1.752 5.617,1.898 0.277,0.145 10 D74 5.385,1.965 5.576,2.121 0.191,0.156 10 79 5.34,2.116 5.617,2.262 0.277,0.145 10 D74 5.644,1.381 6.026,1.530 0.382,0.149 10 VTA1 5.644,1.748 6.026,1.897 0.382,0.149 10 VTA2 5.644,2.036 5.960,2.185 0.316,0.149 10 ETA 5.389,2.407 5.579,2.552 0.191,0.145 10 57 5.344,2.549 5.618,2.698 0.274,0.149 10 A24 5.389,2.768 5.579,2.913 0.191,0.145 10 59 5.344,2.91 5.618,3.059 0.274,0.149 10 A24 5.389,3.136 5.579,3.282 0.191,0.145 10 55 5.344,3.279 5.618,3.428 0.274,0.149 10 A24 5.389,3.529 5.579,3.674 0.191,0.145 10 56 5.344,3.671 5.618,3.820 0.274,0.149 10 A24 5.389,3.896 5.579,4.041 0.191,0.145 10 58 5.344,4.038 5.618,4.187 0.274,0.149 10 A24 5.389,4.262 5.579,4.408 0.191,0.145 10 60 5.344,4.405 5.618,4.554 0.274,0.149 10 A24 5.644,2.462 6.050,2.618 0.406,0.156 10 VCPA 5.644,3.278 5.957,3.434 0.312,0.156 10 VPA 5.644,3.961 5.957,4.117 0.312,0.156 10 EPA 5.644,3.67 6.019,3.826 0.375,0.156 10 VPA2 5.644,4.325 6.019,4.481 0.375,0.156 10 EPA2 5.644,2.834 6.050,2.990 0.406,0.156 10 VCP2 0.219,1.002 0.444,1.158 0.225,0.156 10 D9 0.219,1.144 1.741,1.300 1.522,0.156 10 Throttle Position Sensor 2.594,1.016 2.828,1.172 0.235,0.156 10 VC 2.521,1.381 2.829,1.535 0.309,0.154 10 VTA 2.453,1.735 2.826,1.900 0.373,0.165 10 VTA2 2.624,2.104 2.840,2.270 0.216,0.165 10 E2 2.904,0.932 3.023,1.088 0.119,0.156 10 5 2.904,1.29 3.023,1.446 0.119,0.156 10 6 2.904,1.657 3.023,1.813 0.119,0.156 10 4 2.904,2.016 3.023,2.172 0.119,0.156 10 3 0.21,2.531 0.500,2.687 0.290,0.156 10 A14 0.21,2.674 1.347,3.006 1.137,0.332 10 Accelerator Pedal Position Sensor 2.433,2.555 2.847,2.705 0.414,0.150 10 VCPA 2.433,2.919 2.847,3.070 0.414,0.150 10 VCP2 2.522,3.279 2.843,3.429 0.321,0.150 10 VPA 2.447,3.676 2.861,3.826 0.414,0.150 10 VPA2 2.527,4.031 2.849,4.181 0.321,0.150 10 EPA 2.452,4.404 2.866,4.554 0.414,0.150 10 EPA2 2.904,2.459 3.023,2.620 0.119,0.161 10 4 2.904,2.819 3.023,2.980 0.119,0.161 10 1 2.904,3.179 3.023,3.339 0.119,0.161 10 6 2.904,3.576 3.023,3.736 0.119,0.161 10 3 2.904,3.952 3.023,4.112 0.119,0.161 10 5 2.904,4.311 3.023,4.472 0.119,0.161 10 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up




OK

SYSTEM OK

NG

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and Techstream on.


c.

Check the communication between the Techstream and ECM.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



B

3.CHECK MIL (THROTTLE POSITION SENSOR)

A

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the D9 throttle body connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B

HINT:

Perform "Inspection After Repair" after replacing the throttle body (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

A

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the A14 accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

5.CHECK MIL (CANISTER PUMP MODULE)

A

REPLACE ACCELERATOR PEDAL POSITION SENSOR

5.CHECK MIL (CANISTER PUMP MODULE)
a.

Disconnect the R12 canister pump module connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

6.CHECK MIL (AIR SWITCHING VALVE for Bank 1)

A

6.CHECK MIL (AIR SWITCHING VALVE for Bank 1)
a.

Disconnect the D58 air switching valve (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

7.CHECK MIL (AIR SWITCHING VALVE for Bank 2)

A

7.CHECK MIL (AIR SWITCHING VALVE for Bank 2)
a.

Disconnect the D59 air switching valve (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)

A

8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
a.

Disconnect the D46 power steering oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

9.CHECK MIL (CAMSHAFT POSITION SENSOR)

A

REPLACE POWER STEERING OIL PRESSURE SENSOR

9.CHECK MIL (CAMSHAFT POSITION SENSOR)
a.

Disconnect the D6 camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)

A

10.CHECK MIL (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the D3 crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

11.CHECK MIL (VVT SENSOR for Intake Side of Bank 1)

A

11.CHECK MIL (VVT SENSOR for Intake Side of Bank 1)
a.

Disconnect the D37 VVT sensor (for Intake Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

12.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 1)

A

REPLACE VVT SENSOR (for Intake Side of Bank 1)

12.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 1)
a.

Disconnect the D40 VVT sensor (for Exhaust Side of Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

13.CHECK MIL (VVT SENSOR for Intake Side of Bank 2)

A

REPLACE VVT SENSOR (for Exhaust Side of Bank 1)

13.CHECK MIL (VVT SENSOR for Intake Side of Bank 2)
a.

Disconnect the D39 VVT sensor (for Intake Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

14.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 2)

A

REPLACE VVT SENSOR (for Intake Side of Bank 2)

14.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 2)
a.

Disconnect the D41 VVT sensor (for Exhaust Side of Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

15.CHECK HARNESS AND CONNECTOR

A

REPLACE VVT SENSOR (for Exhaust Side of Bank 2)

15.CHECK HARNESS AND CONNECTOR
a.

Disconnect the D9 throttle body connector.


b.

Disconnect the A14 accelerator pedal position sensor connector.


c.

Disconnect the R12 canister pump module connector.


d.

Disconnect the D58 air switching valve (for Bank 1) connector.


e.

Disconnect the D59 air switching valve (for Bank 2) connector.


f.

Disconnect the D46 power steering oil pressure sensor connector.


g.

Disconnect the D6 camshaft position sensor connector.


h.

Disconnect the D3 crankshaft position sensor connector.


i.

Disconnect the D37 VVT sensor (for Intake Side of Bank 1) connector.


j.

Disconnect the D40 VVT sensor (for Exhaust Side of Bank 1) connector.


k.

Disconnect the D39 VVT sensor (for Intake Side of Bank 2) connector.


l.

Disconnect the D41 VVT sensor (for Exhaust Side of Bank 2) connector.


m.

Disconnect the A24 and D74 ECM connectors.


n.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D74-80 (VCTA) - Body ground Always 10 kΩ or higher
A24-57 (VCPA) - Body ground Always 10 kΩ or higher
A24-59 (VCP2) - Body ground Always 10 kΩ or higher
D74-66 (VCV2) - Body ground Always 10 kΩ or higher
D74-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR