Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › HEATED OXYGEN SENSOR
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233939 HEATED OXYGEN SENSOR A

3UR-FBE ENGINE CONTROL  HEATED OXYGEN SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

a.
A158663

Install the heated oxygen sensor to the front exhaust pipe assembly by hand.


b.
A148589E07
1.521,1.496 1.711,1.673 0.190,0.177 10 *a 2.882,1.678 3.190,1.835 0.307,0.157 10 SST 2.601,0.993 3.042,1.505 3.042,1.505 3.042,1.629 false

Using SST, tighten the heated oxygen sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

Text in Illustration
*a Fulcrum length

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 89465 2.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

a.
A158663

Install the heated oxygen sensor to the front No. 2 exhaust pipe assembly by hand.


b.
A148589E08
1.53,1.562 1.729,1.738 0.199,0.177 10 *a 2.882,1.678 3.190,1.835 0.307,0.157 10 SST 2.601,0.993 3.042,1.505 3.042,1.505 3.042,1.629 false

Using SST, tighten the heated oxygen sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

Text in Illustration
*a Fulcrum length

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the heated oxygen sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 37140 5.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 37117 6.INSTALL PROPELLER SHAFT HEAT INSULATOR