Home › Engine / Hybrid System › 3UR-FBE LUBRICATION › OIL PUMP
RM27M0U _51 Engine / Hybrid System _049116 3UR-FBE LUBRICATION _0234080 OIL PUMP A

3UR-FBE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 16400 6.REMOVE RADIATOR ASSEMBLY

Hide 17880 7.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 9.DISCONNECT ENGINE WIRE

a.

Engine Room LH Side:

i.
A162560

Remove the engine room relay block cover.


ii.

Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.


iii.
A153551

Disconnect the 4 air injection control driver connectors.


iv.
A163944

Disconnect the 2 wire harness clamps.


v.
A259655

Disconnect the injector connector.


vi.

Disconnect the 4 ignition coil connectors.


vii.

Disconnect the 2 VVT sensor connectors.


viii.

Disconnect the 5 clamps.


ix.

Remove the 2 bolts and ground wire LH.


x.
A162562

Disconnect the engine coolant temperature sensor connector.


xi.

Disconnect the 2 camshaft timing oil control valve connectors.


xii.

Disconnect the camshaft position sensor connector.


xiii.

Disconnect the 3 clamps.


xiv.

Disconnect the cooler compressor connector.



b.
A264086

Engine Room RH Side:

i.

Disconnect the 2 camshaft timing oil control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the injector connector.


iv.

Disconnect the 2 VVT sensor connectors.


v.

Remove the 2 bolts and ground wire RH.


vi.

Disconnect the 2 air pump connectors.


vii.

Disconnect the throttle position sensor and throttle control motor connector.


viii.

Disconnect the 7 clamps.



c.
A162564E03
2.281,1.333 2.198,1.333 2.198,1.333 1.656,1.875 true 2.302,1.208 2.49,1.448 0.188,0.24 10 true *1

Disconnect the 2 clamps and power steering oil pressure switch connector.

Text in Illustration
*1 Junction Connector


d.

Disconnect the clamp and junction connector.


Hide 17111 10.REMOVE INTAKE MANIFOLD

Hide 11.DISCONNECT AIR PUMP HOSE AND WIRE HARNESS

a.
A163452E03
1.719,0.115 1.625,0.115 1.625,0.115 1.313,0.208 false 1.906,1.667 1.833,1.667 1.833,1.667 1.594,1.5 true 1.771,0.031 1.948,0.177 0.177,0.146 10 false *1 1.948,1.583 2.177,1.75 0.229,0.167 10 true *2

Slide the 2 clamps and disconnect the No. 2 air hose and No. 3 air hose from the air tube sub-assembly.

Text in Illustration
*1 No. 3 Air Hose
*2 No. 2 Air Hose


b.

Disconnect the 2 clamps.


Hide 12.DISCONNECT HEATER HOSE AND PIPE

a.
A163380

Remove the 2 bolts.


b.

Slide the 3 clamps and disconnect the 3 hoses.


Hide 88320 13.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A163332

Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 23902 14.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A165142E07
0.104,0.042 0.344,0.24 0.24,0.198 10 false *a 0.177,2.365 0.354,2.552 0.177,0.188 10 false *b

Remove the 2 bolts and disconnect the No. 2 fuel tube sub-assembly.

Text in Illustration
*a LH Side
*b RH Side


Hide 83520 16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 16268A 17.REMOVE NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)

a.
A165547

Slide the 4 clamps and disconnect the 4 hoses from the No. 2 water by-pass pipe.


b.

Remove the 3 bolts and No. 2 water by-pass pipe.


Hide 15781 18.REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)

Hide 15671 19.REMOVE OIL FILTER BRACKET (w/ Oil Cooler)

Hide 20.REMOVE OIL FILTER BRACKET (w/o Oil Cooler)

a.
A163541

Remove the 2 bolts, 2 nuts and oil filter bracket.


b.
A162470

Remove the 2 O-rings.


Hide 11452 21.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 44320 22.DISCONNECT VANE PUMP ASSEMBLY

a.
A163289

Remove the 2 bolts and disconnect the vane pump assembly.


Hide 27020 23.REMOVE GENERATOR ASSEMBLY

a.
A163292

Disconnect the generator connector.


b.

Remove the terminal cap and nut, and disconnect the generator wire.


c.
A380090

Remove the bolt and disconnect the wire harness bracket from the generator assembly.


d.
A163293

Remove the 2 bolts, 2 nuts and generator assembly.


e.

Remove the 2 stud bolts.


Hide 16261G 24.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A308519

Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.


Hide 16206 25.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A162550

Remove the bolt and disconnect the air tube sub-assembly.


b.
A162551

Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.


c.

Remove the 2 bolts and water by-pass pipe sub-assembly.


Hide 16297 26.DISCONNECT NO. 9 WATER BY-PASS HOSE

a.
A291559E04
2.177,0.115 2.292,0.115 2.292,0.115 2.417,0.479 true 1.146,0.75 1.313,0.75 1.313,0.75 1.823,1.167 true 0.917,0.677 1.115,0.875 0.198,0.198 10 true *1 1.969,0.021 2.156,0.219 0.188,0.198 10 false *2

Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose


Hide 16293 27.CONNECT NO. 10 WATER BY-PASS HOSE

a.

Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.


Hide 16355 28.REMOVE FRONT WATER BY-PASS JOINT

a.
A291566

Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.


b.

Remove the 4 nuts, front water by-pass joint and 2 gaskets.


Hide 17303 31.REMOVE AIR TUBE SUB-ASSEMBLY

a.
A162553

Remove the bolt, disconnect the 2 hoses, and remove the air tube sub-assembly.


Hide 16323 32.REMOVE WATER INLET HOUSING

a.
A162554

Remove the 3 bolts, water inlet housing and gasket.


Hide 16173 33.REMOVE WATER PUMP PULLEY

a.
A162556E03
0.5,1.513 0.717,1.701 0.217,0.188 10 *a 0.62,1.501 0.62,1.438 false 0.62,1.438 1.074,1.193 false

Using SST, hold the water pump pulley.

Text in Illustration
*a SST

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts and water pump pulley.


Hide 16603 34.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A162557

Remove the bolt and No. 1 idler pulley sub-assembly.


Hide 16211 35.REMOVE FAN BRACKET ASSEMBLY

a.
A162558

Remove the 4 bolts and fan bracket assembly.


Hide 16620 36.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the standard bolt, 6 mm hexagon bolt and V-ribbed belt tensioner assembly.


Hide 19500 37.REMOVE IGNITION COIL ASSEMBLY

a.

Remove the 8 bolts and 8 ignition coils.


Hide 11202 38.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A162523

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 11201 39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A162525

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162526

Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 13471 40.REMOVE CRANKSHAFT PULLEY

a.
A164228E07
0.188,0.948 0.188,1.896 false 0.188,1.896 0.354,1.333 false 0.052,1.938 0.375,2.125 0.323,0.188 10 false SST 1.167,2.604 1.51,2.781 0.344,0.177 10 false *a 3.021,1.927 3.198,2.115 0.177,0.188 10 true *b

Using SST, loosen the crankshaft pulley set bolt.

Text in Illustration
*a SST
*b Turn
*c Hold

SST
09213-70011  
09330-00021  


b.

Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.


c.
A164229E06
0.458,0.583 0.552,0.583 0.552,0.583 0.646,1.052 true 0.083,0.51 0.396,0.688 0.313,0.177 10 false SST 2.99,2.375 3.188,2.625 0.198,0.25 10 true *b 0.688,2.885 0.885,3.135 0.198,0.25 10 true *c

Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.

Text in Illustration
*a SST
*b Turn
*c Hold

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05011)


Hide 41.DISCONNECT WIRE HARNESS CLAMP BRACKET

a.
A163733

Remove the bolt and disconnect the wire harness clamp bracket.


Hide 11302 42.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A162529E02
1.826,0.549 2.068,0.719 0.242,0.170 10 *1

Remove the 28 bolts and nut shown in the illustration.

Text in Illustration
*1 Nut


b.
A162530

Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.



c.
A162531

Remove the oil pump gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan sub-assembly.


Hide 16322 43.REMOVE WATER INLET PIPE

a.
A162532

Remove the water inlet pipe from the No. 1 heat exchanger cover.


b.

Remove the 2 O-rings from the water inlet pipe.