Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A5  Transfer Synchronization Actuator Circuit Open  P17A6  Transfer Synchronization Actuator Circuit Low  


DESCRIPTION

This DTC is detected when an open circuit or short to ground is detected in the solenoid coil drive circuit.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A5
1.

Ignition switch ON (when not switching between 2WD and 4H)

2.

Open circuit in the solenoid coil drive circuit

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Solenoid coil sub-assembly

·

Transfer shift actuator assembly


P17A6
1.

Ignition switch ON (when switching between 2WD and 4H)

2.

Short to ground in the solenoid coil drive circuit

3.

0.1 seconds or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Solenoid coil sub-assembly

·

Transfer shift actuator assembly



WIRING DIAGRAM

C290927E03
0.948,2.01 1.906,2.385 0.958,0.375 10 false Solenoid Coil Sub-assembly 2.229,2.021 3.531,2.385 1.302,0.365 10 false Transfer Shift Actuator Assembly 1.385,2.708 2.635,2.938 1.25,0.229 10 false Transfer Assembly 4.615,2.708 5.073,2.896 0.458,0.188 10 false A26 4.604,2.854 6.479,3.063 1.875,0.208 10 false 4 Wheel Drive Control ECU 4.75,1.167 5.208,1.354 0.458,0.188 10 false 6 3.563,1.083 4.021,1.271 0.458,0.188 10 false 3 3.479,1.313 3.938,1.5 0.458,0.188 10 false D67 4.969,1.323 5.427,1.51 0.458,0.188 10 false SCC 3.073,1.208 3.531,1.396 0.458,0.188 10 false SCC 2.219,1.323 2.677,1.51 0.458,0.188 10 false A 2.219,1.104 2.677,1.292 0.458,0.188 10 false 2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A26 4 wheel drive control ECU connector.


b.

Disconnect the D67 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-6 (SCC) - D67-3 (SCC) Always Below 1 Ω
A26-6 (SCC) or D67-3 (SCC) - Body ground Always 10 kΩ or higher




OK

2.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (SCC TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (SCC TERMINAL)
C291017E01
0.202,0.17 0.601,0.482 0.399,0.312 10 *a 1.898,1.946 2.29,2.74 false 2.118,2.748 2.482,2.953 0.364,0.205 10 SCC

a.

Disconnect the D67 transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
DTC P17A5 is output
Tester Connection Condition Specified Condition
3 (SCC) - Body ground Always Below 5 Ω

DTC P17A6 is output
Tester Connection Condition Specified Condition
3 (SCC) - Body ground Always 1 Ω or higher


Text in Illustration
*a Component without harness connected
(Transfer Shift Actuator Assembly)



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

3.INSPECT SOLENOID COIL SUB-ASSEMBLY
3.INSPECT SOLENOID COIL SUB-ASSEMBLY
C295407E01
0.368,0.061 0.899,0.379 0.531,0.318 10 *a

a.

Disconnect the A solenoid coil sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
DTC P17A5 is output
Tester Connection Condition Specified Condition
2 - Body ground Always Below 5 Ω

DTC P17A6 is output
Tester Connection Condition Specified Condition
2 - Body ground Always 1 Ω or higher


Text in Illustration
*a Component without harness connected
(Solenoid Coil Sub-assembly)



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPLACE SOLENOID COIL SUB-ASSEMBLY