Home › Steering › POWER STEERING › STEERING GEAR
RM27M0U _55 Steering _049130 POWER STEERING _0234203 STEERING GEAR A

POWER STEERING  STEERING GEAR  INSTALLATION  


PROCEDURE

Hide 44250 1.INSTALL POWER STEERING GEAR ASSEMBLY

C353084E01
0.552,0.042 1.302,0.25 0.75,0.208 12 false for 2WD: 3.906,0.031 4.656,0.24 0.75,0.208 12 false for 4WD:

a.

Install the power steering gear with the 2 bolts and 2 nuts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 44410 2.INSTALL PRESSURE FEED TUBE ASSEMBLY

a.
C181258

Temporarily connect the pressure feed tube to the power steering gear.


b.
C181255

Install the pressure feed tube clamp with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


c.
C181256E02
2.74,0.344 3.271,0.698 0.531,0.354 10 false Fulcrum Length

Using a union nut wrench, tighten the pressure feed tube (pressure feed tube side).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Use the formula calculate special torque values for situations for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.
C181257E01
2.65,0.301 3.237,0.612 0.587,0.311 10 Fulcrum Length

Using a union nut wrench, tighten the pressure feed tube (return tube side).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Use the formula calculate special torque values for situations for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 45047 3.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Connect the tie rod end LH to the steering knuckle with the nut.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


b.

Install a new cotter pin.

HINT:

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



Hide 45046 4.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 45203 5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

C155151E04
0.99,1.469 1.646,1.344 false 0.99,1.469 1.677,1.563 false 0.198,1.375 0.948,1.542 0.75,0.167 10 true Matchmark

a.

Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.


b.

Install the bolt.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 6.INSTALL ENGINE ASSEMBLY

a.

for 3UR-FBE:

Install the engine assembly (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


b.

for 1UR-FE:

Install the engine assembly (See page Engine / Hybrid System>1UR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


c.

for 3UR-FE:

Install the engine assembly (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


Hide 7.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 11.CHECK POWER STEERING FLUID LEVEL (for 3UR-FE, 3UR-FBE)

Hide 12.INSPECT FOR POWER STEERING FLUID LEAK

Hide 13.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

HINT:

Perform this procedure with the front of the vehicle jacked up.


Hide 14.ADJUST FRONT WHEEL ALIGNMENT

a.

Adjust the front wheel alignment (See page Suspension>SUSPENSION>FRONT WHEEL ALIGNMENT>ADJUSTMENT).