Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM27M0U _51 Engine / Hybrid System _049105 3UR-FBE ENGINE MECHANICAL _0234016 ENGINE ASSEMBLY A

3UR-FBE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly RH, cylinder head sub-assembly LH, No. 1 camshaft sub-assembly, No. 2 camshaft sub-assembly, No. 3 camshaft sub-assembly, No. 4 camshaft sub-assembly, camshaft timing gear RH, camshaft timing gear LH, camshaft timing exhaust gear RH, camshaft timing exhaust gear LH, piston or piston ring (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.REMOVE ENGINE STAND

a.
U151520

Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Item Part No.
Engine hanger 12281-38150
Bolt 90119-A0166



b.

Attach an engine sling device and hang the engine with a chain block.


c.

Remove the bolts and engine assembly from the engine stand.


Hide 17105 2.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 3.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 4.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.

NOTICE:

Make sure that the engine is clear of all wiring and hoses.



b.

Attach the engine mounting insulators to the vehicle.


c.
A163780E06
0.104,0.104 0.417,0.51 0.313,0.406 10 true RH: 0.115,2.354 0.417,2.771 0.302,0.417 10 true LH:

Install the 4 engine mounting insulator bolts.

Torque:
79 N*m (806 kgf*cm, 58 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 16268 5.INSTALL NO. 1 WATER BY-PASS PIPE

a.
A163785

Connect the hose and install the water by-pass pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 32101 6.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E02
1.359,1.727 1.661,1.883 0.302,0.156 10 SST 0.829,1.22 0.829,1.812 0.829,1.812 1.312,1.812 false 1.076,1.054 1.076,1.812 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A217514C02
0,0 0,0 false
V100135

Engine Side


Install the crankshaft angle sensor rotor.

HINT:
·

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

·

As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A217515C02
1.865,3.385 2.625,3.125 2.625,3.125 2.76,3.125 false 1.177,0.417 1.76,0.25 1.76,0.25 1.896,0.25 false 1.958,0.177 2.271,0.333 0.313,0.156 10 false *1 2.844,3.042 3.156,3.198 0.313,0.156 10 false *2
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Automatic Transmission Side


Install the drive plate and rear drive plate spacer onto the crankshaft.

HINT:

As the rear drive plate spacer and the drive plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



d.

Install the drive plate and ring gear and bolts.

HINT:

The bolts are tightened in 2 progressive steps.


i.

Clean the bolts and bolt holes.


ii.
A380777C01
1.833,1.188 2.052,0.479 2.052,0.479 2.198,0.479 false 2.26,0.406 2.573,0.563 0.313,0.156 10 false *1
*1 Adhesive


Apply adhesive to 2 or 3 threads of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



iii.
A214574E02
1.49,0.448 1.594,0.594 0.104,0.146 10 true 9 1.844,0.448 1.938,0.604 0.094,0.156 10 true 1 1.5,1.625 1.594,1.802 0.094,0.177 10 true 2 2.25,1.052 2.365,1.198 0.115,0.146 10 true 3 1.094,1.031 1.188,1.188 0.094,0.156 10 true 4 2.188,1.375 2.302,1.521 0.115,0.146 10 true 5 1.167,0.708 1.281,0.865 0.115,0.156 10 true 6 2.177,0.719 2.302,0.875 0.125,0.156 10 true 7 1.167,1.375 1.26,1.521 0.094,0.146 10 true 8 1.813,1.625 1.99,1.771 0.177,0.146 10 true 10

Step 1:

Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate installation bolts.

·

Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.




iv.

Mark the top of each drive plate installation bolt with paint.


v.

Step 2:

Tighten the drive plate installation bolts 90° as shown in the illustration.


vi.

Check that the painted marks are now at a 90° angle to the top.

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.




Hide 35000 7.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

Hide 17104 10.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 11.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 12.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 53739A 13.INSTALL FRONT FENDER APRON SEAL REAR RH

Hide 53736 14.INSTALL FRONT FENDER APRON SEAL RH

Hide 37140 15.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

a.

Install the front propeller shaft (See page Drivetrain>PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY>INSTALLATION).


Hide 37110 16.INSTALL PROPELLER SHAFT ASSEMBLY

a.

for 2WD:

Install the propeller shaft (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 2WD)>INSTALLATION).


b.

for 4WD:

Install the propeller shaft (See page Drivetrain>PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for 4WD)>INSTALLATION).


Hide 17410 17.INSTALL EXHAUST PIPE ASSEMBLY

a.

Install the exhaust pipe assembly (See page Engine / Hybrid System>3UR-FBE EXHAUST>EXHAUST PIPE>INSTALLATION).


Hide 88320 20.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 21.CONNECT WIRE HARNESS AND HOSE

a.
A163790

Connect the 2 connectors and 2 clips to the engine room junction block.


b.

Install the engine wire with the nut. Then connect the 2 clips.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 air injection control driver connectors.


d.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the cable to the positive (+) battery terminal.


f.

Install the wire to the positive (+) battery cable with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


g.
A163791

Connect the 2 air injection system hoses.


h.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.

Connect the 2 air pump connectors and install the connector bracket with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


j.
U151465

Connect the 4 connectors to the connector holder block.


k.
A163788

Connect the heater hoses.


l.

Connect the ECM connector and clamp.

HINT:

Refer to the following procedures to connect the ECM connector (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>ECM>INSTALLATION).



m.
A163789

Connect the union to check valve hose.


n.

Connect the purge line hose.


Hide 23801P 22.CONNECT FUEL MAIN AND RETURN HOSE

a.
A308865

Connect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Install the fuel pipe clamp.


Hide 53294C 26.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 27.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 53101 28.INSTALL RADIATOR GRILLE SUB-ASSEMBLY

Hide 16572 29.INSTALL OUTLET RADIATOR HOSE

Hide 16571 30.INSTALL INLET RADIATOR HOSE

Hide 17700 31.INSTALL AIR CLEANER ASSEMBLY

a.
A309638E06
0.031,0.042 0.885,0.469 0.854,0.427 10 true for Type A: 0.031,2.24 0.938,2.729 0.906,0.49 10 true for Type B:

Install the air cleaner case with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the air cleaner element onto the air cleaner case.


c.
A309637E06
0.052,0.042 0.938,0.438 0.885,0.396 10 true for Type A: 0.052,2.229 0.906,2.583 0.854,0.354 10 true for Type B:

Install the air cleaner cap.

i.

for Type A:

Install the air cleaner cap and fasten the 4 hook clamps.


ii.

for Type B:

Install the air cleaner cap and fasten the 2 hook clamps.


iii.

Connect the MAF meter connector.


iv.

Attach the wire harness clamp.



Hide 17880 32.INSTALL AIR CLEANER HOSE ASSEMBLY

a.
U151488

Install the air cleaner hose with the 2 clamps.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Connect the vacuum hose.


c.

Connect the ventilation hose.


Hide 35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 36.INSPECT FOR OIL LEAK

Hide 40.INSPECT SHIFT LEVER POSITION

Hide 11209 41.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
U151563E02
2.271,1.365 2.198,1.365 2.198,1.365 2.198,1.188 false 0.927,1.667 1.125,1.667 false 2.323,0.417 2.969,0.583 0.646,0.167 10 false Bracket 2.313,1.302 2.708,1.469 0.396,0.167 10 false Hook 0.51,0.781 1.177,0.99 0.667,0.208 10 false Grommet 1.156,1.594 1.385,1.76 0.229,0.167 10 false Pin

Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.


Hide 55701J 42.INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

Hide 85110 43.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Install the windshield wiper motor (See page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 53301 44.INSTALL HOOD SUB-ASSEMBLY

a.
A308967

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

NOTICE:

Install the hood support while supporting the hood by hand.



c.

Attach the hood support clips.

NOTICE:

Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



Hide 53301 45.ADJUST HOOD SUB-ASSEMBLY