Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Wireless Transmitter Memory Function does not Operate  


DESCRIPTION

With the ignition switch off and the driver door closed, pressing the manual lock or unlock switch on the power window regulator master switch assembly while holding a seat memory switch (M1 switch or M2 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After the registration is completed, the answer back buzzer sounds.

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

CAN communication DTC is not output.




OK

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the manual door lock/unlock function by using the power window regulator master switch assembly (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Manual lock/unlock function operates normally.




OK

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless lock/unlock function of wireless door lock control system (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Wireless lock/unlock function operates normally.




OK

4.CHECK SEAT POSITION MEMORY FUNCTION

NG

4.CHECK SEAT POSITION MEMORY FUNCTION
a.

Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

5.CHECK SEAT POSITION RESTORING FUNCTION

NG

Go to OTHER FLOW CHART (Power Seat Position is not Memorized)

5.CHECK SEAT POSITION RESTORING FUNCTION
a.

Perform a seat position restoring function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat position will not return to the memorized position if 2 seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.




OK

6.READ VALUE USING TECHSTREAM (D DOOR COURTESY)

NG

Go to OTHER FLOW CHART (Power Seat does not Return to Memorized Position)

6.READ VALUE USING TECHSTREAM (D DOOR COURTESY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the Techstream.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy Front door courtesy light switch assembly signal / ON or OFF ON: Driver door open
OFF: Driver door closed
-


OK:

ON or OFF appears on the screen according to the driver door condition.



OK

7.CHECK MEMORY CALL REGISTRATION FUNCTION

NG

7.CHECK MEMORY CALL REGISTRATION FUNCTION
a.

When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.

·

Turn the ignition switch is off.

·

Press and hold the M1 or M2 seat memory switch.

·

Driver door closed.

·

Carry the key.



b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


OK:

Buzzer sounds normally.



OK

8.CHECK MEMORY CALL FUNCTION

NG

9.REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
8.CHECK MEMORY CALL FUNCTION
a.

Turn the ignition switch off.


b.

Close and lock all doors.


c.

Unlock the driver door by pressing the unlock switch of the memory call registered key while holding the memory call registered key.


d.

Open the driver door and check that the driver seat moves to the memorized position (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Driver seat moves to the memorized position.




OK

NG

Go to OTHER FLOW CHART (Wireless-linked Return Function does not Operate)

9.REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Temporarily replace the main body ECU (driver side junction block assembly) with a new or normally functioning one.



NEXT

10.CHECK MEMORY CALL REGISTRATION FUNCTION
10.CHECK MEMORY CALL REGISTRATION FUNCTION
a.

When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.

·

Turn the ignition switch is off

·

Press and hold the M1 or M2 seat memory switch

·

Driver door closed

·

Carry the key



b.

Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


OK:

Buzzer sounds normally.



OK

END (MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK ASSEMBLY] WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY