Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Power Easy Access System Function does not Operate  


DESCRIPTION

When the ignition switch is off and the shift lever is in P, the power seat slides rearwards when the seat belt tongue plate is disengaged from the front seat inner belt assembly LH (auto away function). Also the power seat slides forward when the seat belt tongue plate is engaged to the front seat inner belt assembly LH with the ignition switch ACC or ON, and the shift lever in P.


WIRING DIAGRAM

B357073E01
2.878,2.53 4.333,2.859 1.455,0.330 10 Position Control ECU and Switch Assembly 0.861,3.419 2.566,3.582 1.706,0.163 10 : CAN Communication Line 0.294,2.389 2.119,2.721 1.824,0.332 10 Main Body ECU (Driver Side Junction BLock Assembly) 3.565,1.339 3.966,1.495 0.401,0.156 10 DBCL 5.596,1.339 5.919,1.481 0.323,0.142 10 RDC 5.61,1.871 5.738,2.027 0.128,0.156 10 E 4.027,1.255 4.201,1.393 0.174,0.139 10 10 5.414,1.255 5.535,1.417 0.121,0.163 10 5 5.414,1.78 5.525,1.919 0.111,0.139 10 6 3.523,1.871 3.961,2.027 0.438,0.156 10 SGND 4.055,1.78 4.166,1.919 0.111,0.139 10 1 5.363,2.441 6.493,2.803 1.130,0.362 10 Front Seat Inner Belt Assembly LH 5.367,2.259 5.632,2.422 0.265,0.163 10 P7 2.878,2.358 3.159,2.507 0.281,0.149 10 Z10

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

CAN communication DTC is not output.




OK

2.CHECK FRONT POWER SEAT OPERATION

NG

2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Each function of power seat operates normally by using the front power seat seat switches.


Result
Result Proceed to
Power seat functions operate normally A
All power seat functions do not operate B
One or more power seat motors do not operate C



A

3.CHECK SEAT POSITION MEMORY FUNCTION

B

Go to OTHER FLOW CHART (Front Power Seat does not Operate with Front Power Seat Switch)

C

Go to OTHER FLOW CHART (One or more Power Seat Motors do not Operate)

3.CHECK SEAT POSITION MEMORY FUNCTION
a.

Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

4.READ VALUE USING TECHSTREAM (DRIVER SEAT BUCKLE SW)

NG

4.READ VALUE USING TECHSTREAM (DRIVER SEAT BUCKLE SW)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Driver Seat Buckle SW Status of the driver seat belt / ON or OFF ON: Tongue plate is engaged
OFF: Tongue plate is not engaged
-

OK:

"ON" and "OFF" appears on the screen.




OK

5.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

7.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
5.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



NEXT

6.CHECK POWER SEAT POWER EASY ACCESS SYSTEM
6.CHECK POWER SEAT POWER EASY ACCESS SYSTEM
a.

Check that the power seat easy access system operates normally when engaging and disengaging the tongue plate of the front seat inner belt with the shift lever in P (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Power seat power easy access system is normal.




OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

7.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.

Remove the front seat inner belt assembly LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Inspect the front seat inner belt assembly LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY LH)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Disconnect the P7 front seat inner belt assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-10 (DBCL) - P7-5 (RDC) Always Below 1 Ω
Z10-1 (SGND) - P7-6 (E) Always Below 1 Ω
Z10-10 (DBCL) or P7-5 (RDC) - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or P7-6 (E) - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR