Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM27M0U _51 Engine / Hybrid System _049139 CRUISE CONTROL _0234343 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch operates 7 functions: SET, COAST, TAP-DOWN, RESUME, ACCEL, TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control SET, COAST, RESUME, ACCEL and CANCEL.

WIRING DIAGRAM

E146089E03
6.438,2.219 6.792,2.385 0.354,0.167 10 false ECM 6.448,2.063 6.74,2.219 0.292,0.156 10 false A24 6.156,1.156 6.365,1.323 0.208,0.167 10 false 45 6.417,1.042 6.76,1.198 0.344,0.156 10 false CCS 4.896,3.5 5.74,3.708 0.844,0.208 10 false Spiral Cable 5.583,1.052 5.854,1.219 0.271,0.167 10 false J45 5.583,2.969 5.854,3.135 0.271,0.167 10 false J45 5.646,0.844 5.813,1.021 0.167,0.177 10 false 1 3.781,3.073 3.948,3.25 0.167,0.177 10 false 1 5.667,2.781 5.823,2.969 0.156,0.188 10 false 2 4.698,0.844 4.865,1.021 0.167,0.177 10 false 4 4.719,2.781 4.875,2.969 0.156,0.188 10 false 3 3.792,1.146 3.948,1.333 0.156,0.188 10 false 3 5.208,1.135 5.552,1.323 0.344,0.188 10 false CCS 5.208,3.073 5.552,3.26 0.344,0.188 10 false ECC 4.667,1.042 4.875,1.208 0.208,0.167 10 false z2 4.656,2.979 4.865,3.146 0.208,0.167 10 false z2 3.875,3.531 4.854,3.885 0.979,0.354 10 false Cruise Control Switch Wire 0.948,3.438 2.719,3.646 1.771,0.208 10 false Cruise Control Main Switch 3.083,2.01 3.656,2.208 0.573,0.198 10 false ON-OFF 2.198,2.01 2.667,2.188 0.469,0.177 10 false + RES 1.313,2.01 1.781,2.188 0.469,0.177 10 false - SET 0.417,2.01 1.052,2.188 0.635,0.177 10 false CANCEL

PROCEDURE

1.READ VALUE USING TECHSTREAM (CRUISE CONTROL MAIN SWITCH)
E107091E01
0.947,0 1.667,0.202 0.720,0.202 10 RES / ACC 2.494,0.891 3.178,1.093 0.684,0.202 10 ON / OFF 1.978,1.71 2.956,1.912 0.978,0.202 10 SET / COAST 0.46,1.08 1.065,1.282 0.605,0.202 10 CANCEL

a.

Using the Techstream, read the Data List (see page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) is SET
OFF: Cruise control main switch (Main CPU) is UNSET
-
Cancel Switch CANCEL switch / ON or OFF ON: CANCEL switch is SET
OFF: CANCEL switch is UNSET
-
SET/COAST Switch -/SET switch / ON or OFF ON: -/SET switch is SET
OFF: -/SET switch is UNSET
-
RES/ACC Switch +/RES switch / ON or OFF ON: +/RES switch is SET
OFF: +/RES switch is UNSET
-

OK:

When cruise control main switch operation is performed, the results are the same as above.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
E337702E02
4.115,2.792 6.563,3.427 2.448,0.635 10 true Component without harness connected: (Cruise Control Main Switch) 3.99,2.052 4.615,2.24 0.625,0.188 10 false CANCEL 6.344,1.021 6.969,1.208 0.625,0.188 10 false ON/OFF 5.031,2.333 6.719,2.531 1.688,0.198 10 false SET / COAST 4.542,0.156 5.917,0.354 1.375,0.198 10 false RES / ACC

a.

Remove the cruise control main switch (see page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Neutral 10 kΩ or higher
RES / ACC 235 to 245 Ω
SET / COAST 620 to 640 Ω
CANCEL 1510 to 1570 Ω
Main Switch OFF 10 kΩ or higher
Main Switch ON Below 1.5 Ω




OK

3.INSPECT SPIRAL CABLE

NG

3.INSPECT SPIRAL CABLE
E344853E01
4.781,0.333 5.083,0.531 0.302,0.198 3.625,2.646 3.927,2.844 0.302,0.198 4.146,2.823 3.896,3.073 false 4.219,2.833 4.385,3.177 false 0.26,0.135 2.667,0.521 2.406,0.385 10 false Component without harness connected: (Spiral Cable) 4.854,0.354 5.167,0.552 0.313,0.198 10 false z2 3.677,2.656 3.917,2.813 0.24,0.156 10 false J45 3.719,3.063 4.177,3.26 0.458,0.198 10 false CCS 4.302,3.188 4.76,3.385 0.458,0.198 10 false ECC


b.

If there are any defects as follows, replace the spiral cable with a new one: Scratches, cracks, dents or chips on the connector or the spiral cable.


c.

Check spiral cable.

i.

Set the spiral cable to the center position (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z2-4 - J45-1 (CCS) Always Below 1 Ω
z2-3 - J45-2 (ECC)



iii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z2-4 - J45-1 (CCS) Always Below 1 Ω
z2-3 - J45-2 (ECC)


NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.





OK

4.INSPECT CRUISE CONTROL SWITCH WIRE

NG

4.INSPECT CRUISE CONTROL SWITCH WIRE
U152686E02
0.146,2.438 2.396,2.792 2.25,0.354 10 false Front view of wire harness connector: (to Cruise Control Main Switch) 0.135,0.167 2.385,0.521 2.25,0.354 10 false Front view of wire harness connector: (to Spiral Cable) 0.354,1.427 0.542,1.573 0.188,0.146 10 false z2

a.

Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z2-4 - 3 Always Below 1 Ω
z2-3 - 1




OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

NG

REPLACE CRUISE CONTROL SWITCH WIRE

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E344854E01
3.25,1.458 3.583,1.688 0.333,0.229 0.771,1.573 1.104,1.802 0.333,0.229 1.49,1.688 1.125,2.042 false 1.625,1.646 2.406,1.375 false 5.313,1.917 5.135,2.479 false 0.552,0.083 2.792,0.469 2.24,0.385 10 false Front view of wire harness connector: (to Spiral Cable) 3.677,0.073 5.948,0.469 2.271,0.396 10 false Front view of wire harness connector: (to ECM) 0.823,1.604 1.281,1.802 0.458,0.198 10 false J45 3.302,1.49 3.76,1.688 0.458,0.198 10 false A24 0.948,2.063 1.406,2.26 0.458,0.198 10 false CCS 2.469,1.292 2.927,1.49 0.458,0.198 10 false ECC 4.99,2.479 5.448,2.677 0.458,0.198 10 false CCS

a.

Disconnect the J45 spiral cable connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J45-1 (CCS) - A24-45 (CCS) Always Below 1 Ω
J45-1 (CCS) - Body ground Always 10 kΩ or higher
J45-2 (ECC) - Body ground Always Below 1 Ω


Result
Result Proceed to
NG A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 3UR-FBE) D



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

D