Home › Drivetrain › AXLE › REAR AXLE SHAFT
RM27M0U _52 Drivetrain _049151 AXLE _0234392 REAR AXLE SHAFT A

AXLE  REAR AXLE SHAFT  INSTALLATION  


PROCEDURE

Hide 42312C 1.INSTALL REAR AXLE SHAFT OIL SEAL

a.
F042743E06
1.552,0.938 2.438,0.625 2.438,0.625 2.021,1.292 false 2.479,0.521 2.781,0.688 0.302,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal.

SST
09950-60020  (09951-00770)
09950-70010  (09951-07150)


b.

Apply MP grease to the lip of the oil seal.

NOTICE:

Do not allow foreign matter, etc. to contact the axle shaft housing hole.



Hide 42312 2.INSTALL REAR AXLE SHAFT

a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle shaft.


c.
C159453

Install the rear axle shaft and parking brake plate with the 4 nuts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


Hide 46430 4.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 5.INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY LH

Hide 46590 6.INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH

Hide 46580 7.INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH

Hide 46550E 8.INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING LH

Hide 9.CHECK PARKING BRAKE INSTALLATION

Hide 42431 10.INSTALL REAR DISC LH

Hide 11.ADJUST PARKING BRAKE SHOE CLEARANCE

Hide 12.CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

a.
C158344

Connect the rear disc brake cylinder and install 2 new bolts.

Torque:
167 N*m (1703 kgf*cm, 123 ft.*lbf)

NOTICE:
·

Do not twist the flexible hose.

·

Make sure that the bolts are free from damage and foreign matter.

·

Do not overtighten the bolts.




Hide 13.CONNECT REAR BRAKE FLEXIBLE HOSE

a.

Set the flexible hose to the connecting point with the brake tube, and then install a new clip.


b.
C154492E06
1.156,0.865 1.344,1.01 1.344,1.01 1.521,1.01 false 1.479,0.156 2.479,0.354 1,0.198 10 false Fulcrum Length 1.563,0.938 2.813,1.167 1.25,0.229 10 false Union Nut Wrench

Using union nut wrench, connect the flexible hose to the brake tube while holding the flexible hose with a wrench.

Torque:
without union nut wrench : 15 N*m (155 kgf*cm, 11 ft.*lbf)
with union nut wrench : 14 N*m (145 kgf*cm, 10 ft.*lbf)

HINT:

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.).


NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.




Hide 14.FILL RESERVOIR WITH BRAKE FLUID

a.

Fill the brake fluid (see page Brake>BRAKE>BRAKE FLUID>REPLACEMENT).


Hide 15.BLEED BRAKE LINE

Hide 16.CHECK BRAKE FLUID LEVEL IN RESERVOIR

Hide 17.CHECK FOR BRAKE FLUID LEAKS

Hide 18.INSTALL REAR WHEEL LH

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 20.INSPECT FOR DIFFERENTIAL OIL LEAK

Hide 21.CHECK PARKING BRAKE PEDAL TRAVEL

Hide 22.ADJUST PARKING BRAKE PEDAL TRAVEL

Hide 23.CHECK SRS WARNING LIGHT

Hide 24.CHECK SPEED SENSOR SIGNAL