Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1207/37  Malfunction in Park / Neutral Position Switch  


DESCRIPTION

The park / neutral position switch signal is sent to the skid control ECU via the CAN communication system.

When there is a malfunction in the CAN communication system, it will be detected by the diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1207/37 When all conditions below are met:
·

Yaw rate sensor is normal.

·

G sensor lateral operation is normal.

·

Vehicle speed is 40 km/h (24.9 mph) or more.

·

Reversing signal is output from ECM for 1 second or more.


·

Park / Neutral position switch

·

ECM

·

CAN communication system

·

Harness or connector

·

Skid control ECU



WIRING DIAGRAM

C312621E01
0.259,2.549 1.630,2.740 1.371,0.191 10 from Ignition Switch 0.259,1.267 1.630,1.458 1.371,0.191 10 from Ignition Switch 2.662,3.53 2.978,3.734 0.316,0.205 10 D35 2.655,3.677 4.561,3.867 1.906,0.191 10 Park / Neutral Position Switch 2.522,4.342 4.275,4.540 1.753,0.198 10 CAN Communication Line 0.203,5.113 0.540,5.310 0.336,0.198 10 A17 0.182,5.26 1.345,5.423 1.163,0.163 10 Skid Control ECU 0.714,4.111 1.183,4.288 0.468,0.177 10 CANH 0.714,4.602 1.183,4.778 0.468,0.177 10 CANL 5.821,4.111 6.290,4.288 0.468,0.177 10 CANH 5.821,4.602 6.290,4.778 0.468,0.177 10 CANL 1.226,3.957 1.541,4.210 0.316,0.253 10 12 1.226,4.454 1.541,4.708 0.316,0.253 10 13 2.774,2.682 3.034,2.914 0.260,0.232 10 2 2.774,1.393 3.034,1.625 0.260,0.232 10 4 3.993,1.393 4.253,1.625 0.260,0.232 10 5 3.993,1.701 4.253,1.934 0.260,0.232 10 7 3.993,2.22 4.253,2.452 0.260,0.232 10 9 3.993,2.759 4.253,2.991 0.260,0.232 10 1 3.993,3.285 4.253,3.517 0.260,0.232 10 6 2.998,1.141 3.258,1.373 0.260,0.232 10 B 2.963,2.458 3.244,2.621 0.281,0.163 10 RB 3.664,3.095 3.931,3.314 0.267,0.218 10 PL 3.72,2.563 3.987,2.781 0.267,0.218 10 RL 3.699,2.017 3.966,2.235 0.267,0.218 10 NL 3.692,1.484 3.959,1.703 0.267,0.218 10 DL 3.783,1.162 3.966,1.380 0.184,0.218 10 L 5.464,4.602 5.759,4.792 0.295,0.191 10 A24 5.464,4.115 5.759,4.305 0.295,0.191 10 A24 5.506,4.405 5.711,4.610 0.205,0.205 10 11 5.499,3.908 5.704,4.113 0.205,0.205 10 10 5.548,2.976 5.704,3.181 0.156,0.205 10 2 5.499,2.437 5.704,2.641 0.205,0.205 10 26 5.499,1.905 5.704,2.109 0.205,0.205 10 25 5.499,1.376 5.704,1.580 0.205,0.205 10 27 4.511,1.267 5.369,1.472 0.857,0.205 10 to ST Relay 5.45,0.644 5.807,0.834 0.357,0.191 10 D74 5.45,1.589 5.807,1.780 0.357,0.191 10 D74 5.45,2.122 5.807,2.312 0.357,0.191 10 D74 5.45,2.654 5.807,2.845 0.357,0.191 10 D74 5.45,3.172 5.807,3.363 0.357,0.191 10 D74 5.457,0.454 5.807,0.624 0.350,0.170 10 120 5.814,0.651 6.303,0.890 0.489,0.239 10 NSW 5.814,1.589 6.303,1.829 0.489,0.239 10 D 5.814,2.136 6.303,2.375 0.489,0.239 10 N 5.814,2.654 6.303,2.893 0.489,0.239 10 R 5.814,3.2 6.303,3.440 0.489,0.239 10 P 6.059,5.169 6.535,5.408 0.475,0.239 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY

B

2.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY
a.
C160109E31
2.375,2.427 2.021,1.938 true 1.604,2.417 1.698,1.927 true 1.979,2.417 1.885,1.927 true 1.646,1.688 1.563,1.198 true 1.063,2.427 1.417,1.938 true 1.813,1.677 2.177,1.188 true 1.375,1.667 1.01,1.177 true 0.052,0 2.635,0.365 2.583,0.365 10 false Component without harness connected: (Park / Neutral Position Switch) 1.313,1.094 1.521,1.271 0.208,0.177 10 false RB 0.885,1.094 1.031,1.271 0.146,0.177 10 false B 1.948,2.479 2.156,2.656 0.208,0.177 10 false PL 2.406,2.458 2.615,2.635 0.208,0.177 10 false L 1.479,2.438 1.688,2.615 0.208,0.177 10 false DL 0.938,2.448 1.146,2.625 0.208,0.177 10 false NL 2.229,1.073 2.438,1.25 0.208,0.177 10 false RL

Disconnect the D35 switch connector.


b.

Measure the resistance of the park / neutral position switch when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (RB) - 6 (PL)
4 (B) - 5 (L)
Shift lever position on P Below 1 Ω
2 (RB) - 1 (RL) Shift lever position on R
2 (RB) - 9 (NL)
4 (B) - 5 (L)
Shift lever position on N
2 (RB) - 7 (DL) Shift lever position on D
Shift lever position on S, "+" and "-"
2 (RB) - 6 (PL)
4 (B) - 5 (L)
Shift lever position not on P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever position not on R
2 (RB) - 9 (NL)
4 (B) - 5 (L)
Shift lever position not on N
2 (RB) - 7 (DL) Shift lever position not on D
Shift lever position not on S, "+" and "-"




OK

3.CHECK PARK / NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

NG

REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY

3.CHECK PARK / NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U152206E02
1.792,1.646 2.146,1.146 true 2.188,1.052 2.396,1.229 0.208,0.177 10 false RB 0.063,0.073 2.469,0.438 2.406,0.365 10 false Front view of wire harness connector: (to Park / Neutral Position Switch) 0.385,1.677 0.76,1.906 0.375,0.229 10 false D35

Disconnect the D35 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D35-2 (RB) - Body ground Ignition switch ON 11 to 14 V
D35-2 (RB) - Body ground Ignition switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK / NEUTRAL POSITION SWITCH - IGNITION SWITCH)

4.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM)
a.
U152333E02
0.74,1.76 1.292,2.698 true 1.344,2.26 1.792,2.875 true 0.646,1.76 1.01,2.698 true 0.573,1.781 0.792,2.719 true 0.552,1.667 0.177,2.708 true 0.073,0.052 2.427,0.406 2.354,0.354 10 false Front view of wire harness connector: (to ECM) 1.49,1.031 1.781,1.208 0.292,0.177 10 false D74 0.146,2.76 0.281,2.927 0.135,0.167 10 false P 0.75,2.771 0.885,2.938 0.135,0.167 10 false N 0.99,2.76 1.125,2.927 0.135,0.167 10 false R 1.292,2.771 1.427,2.938 0.135,0.167 10 false D 1.708,2.896 2.073,3.063 0.365,0.167 10 false NSW

Disconnect the D74 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D74-2 (P) - Body ground
D74-120 (NSW) - Body ground
Ignition switch ON
Shift lever position on P
11 to 14 V
D74-26 (R) - Body ground Ignition switch ON
Shift lever position on R
11 to 14 V*
D74-25 (N) - Body ground
D74-120 (NSW) - Body ground
Ignition switch ON
Shift lever position on N
11 to 14 V
D74-27 (D) - Body ground Ignition switch ON
Shift lever position on D
D74-2 (P) - Body ground
D74-120 (NSW) - Body ground
Ignition switch ON
Shift lever position not on P
Below 1 V
D74-26 (R) - Body ground Ignition switch ON
Shift lever position not on R
D74-25 (N) - Body ground
D74-120 (NSW) - Body ground
Ignition switch ON
Shift lever position not on N
D74-27 (D) - Body ground Ignition switch ON
Shift lever position not on D


HINT:

*: The voltage will drop slightly due to the turning on of the back up light.


Result
Result Proceed to
NG A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 3UR-FBE) D



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

D