Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

If any of the following conditions are detected, the BRAKE warning light remains on:

1.

The ECU connector is disconnected from the skid control ECU.

2.

The brake fluid level is insufficient.

3.

The parking brake is applied.

4.

The EBD system is malfunctioning.

5.

The booster vacuum pressure is abnormal.

6.

The pedal stroke sensor is malfunctioning.


WIRING DIAGRAM

C292927E02
1.188,0.383 1.664,0.566 0.475,0.184 10 CANH 1.206,0.961 1.685,1.130 0.479,0.170 10 CANL 1.707,0.242 1.946,0.433 0.239,0.191 10 39 1.707,0.803 1.974,1.000 0.267,0.198 10 40 1.714,1.433 1.911,1.603 0.198,0.170 10 2 1.329,1.545 1.679,1.729 0.350,0.184 10 IG+ 2.919,1.707 3.309,1.878 0.390,0.172 10 MET 3.913,1.545 5.014,1.729 1.100,0.184 10 from IG2 Relay 2.961,0.656 4.700,0.833 1.739,0.177 10 CAN Communication Line 1.721,4.803 1.981,5.000 0.260,0.198 10 14 1.35,4.964 1.686,5.168 0.336,0.205 10 SW 1.721,5.293 2.002,5.498 0.281,0.205 10 24 1.371,5.426 1.679,5.603 0.309,0.177 10 ES 0.418,5.952 0.747,6.142 0.330,0.191 10 J28 0.418,6.12 1.692,6.310 1.274,0.191 10 Combination Meter 2.302,4.824 2.535,5.001 0.232,0.177 10 1 2.505,4.955 2.752,5.160 0.246,0.205 10 + 2.94,4.955 3.179,5.132 0.239,0.177 10 E 3.157,4.845 3.361,5.042 0.205,0.198 10 2 2.323,5.244 2.623,5.447 0.300,0.203 10 A3 2.309,5.398 3.451,5.783 1.142,0.385 10 Brake Fluid Level Warning Switch 2.12,3.283 2.950,3.633 0.830,0.350 10 from Ignition Switch 2.106,2.561 2.956,2.793 0.850,0.232 10 from Battery 3.668,3.661 4.317,3.862 0.649,0.201 10 IG No. 1 4.537,4.803 5.943,4.993 1.406,0.191 10 Parking Brake Switch 4.537,4.628 4.860,4.839 0.323,0.211 10 A5 5.938,5.952 6.320,6.156 0.382,0.205 10 A17 5.938,6.127 7.153,6.328 1.215,0.201 10 Skid Control ECU 6.092,5.342 6.573,5.528 0.481,0.185 10 GND1 5.791,5.223 6.065,5.400 0.274,0.177 10 16 6.085,4.355 6.574,4.552 0.489,0.198 10 PKB2 5.805,4.263 6.100,4.447 0.295,0.184 10 14 5.56,4.249 5.785,4.482 0.225,0.232 10 1 6.092,2.57 6.401,2.753 0.309,0.184 10 IG1 4.733,2.736 5.701,2.913 0.968,0.177 10 ECU-IG No. 1 6.11,0.947 6.574,1.122 0.463,0.175 10 CANL 6.085,0.397 6.581,0.587 0.496,0.191 10 CANH 5.805,0.228 6.065,0.405 0.260,0.177 10 12 5.819,0.778 6.114,0.969 0.295,0.191 10 13 5.894,2.469 6.114,2.660 0.221,0.191 10 8

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.PREPARE FOR INSPECTION
a.

Check that both of the following conditions are satisfied.

·

The brake fluid level in the brake master cylinder reservoir is correct.

·

The parking brake is released.


HINT:
·

When the ABS warning light remains illuminated, repair the malfunction in the ABS system first.

·

When the SLIP indicator light remains illuminated, repair the malfunction in the VSC system first.





NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check if any ABS DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.INSPECT CAN COMMUNICATION SYSTEM

B

3.INSPECT CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

4.CHECK CONNECTOR CONNECTION CONDITION

B

4.CHECK CONNECTOR CONNECTION CONDITION
a.

Check if the skid control ECU connector is connected securely.

OK:

The connector is connected securely.




OK

5.CHECK PARKING BRAKE SWITCH ASSEMBLY

NG

CONNECT CONNECTOR CORRECTLY

5.CHECK PARKING BRAKE SWITCH ASSEMBLY
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Select Data List mode and check the parking brake switch using the Techstream.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


e.

Check that ON and OFF are properly indicated on the Techstream display when the parking brake lever is operated.

OK:

Techstream display changes in accordance with the parking brake lever operation.




OK

6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
U152282E02
4.823,0.76 5.208,0.135 5.208,0.135 5.406,0.135 false 4.708,1.344 5.323,1.729 5.323,1.729 5.448,1.729 false 1.344,1.792 1.01,2.208 true 1.771,1.792 2.021,2.229 true 0.427,0.115 3.021,0.573 2.594,0.458 10 false Component without harness connected: (Brake Fluid Level Warning Switch) 5.469,0.052 7.146,0.438 1.677,0.385 10 false Brake Master Cylinder Reservoir 5.51,1.635 5.969,1.854 0.458,0.219 10 false Float 0.896,2.25 1.063,2.417 0.167,0.167 10 false E 2.031,2.25 2.198,2.417 0.167,0.167 10 false +

a.

Remove the reservoir tank cap and strainer.


b.

Disconnect the A3 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Float up (Switch OFF) 10 kΩ or higher
1 (+) - 2 (E) Float down (Switch ON) Below 1 Ω


HINT:

If the result is as specified, adjust the brake fluid level to the MAX level after measuring the resistance.




OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
a.
U152283E02
2.208,1.729 2.771,1.156 true 1.99,4.094 2.49,4.219 true 1.521,4.083 1.021,4.208 true 0.094,0.063 2.458,0.427 2.365,0.365 10 false Front view of wire harness connector: (to Combination Meter) 0.229,1.094 0.521,1.281 0.292,0.188 10 false J28 0.615,3.51 0.906,3.698 0.292,0.188 10 false A3 0.896,4.115 1.042,4.323 0.146,0.208 10 false + 2.552,4.146 2.823,4.354 0.271,0.208 10 false E 2.802,1.052 3.083,1.323 0.281,0.271 10 false SW 0.094,2.323 2.458,2.688 2.365,0.365 10 false Front view of wire harness connector: (to Brake Fluid Level Warning Switch)

Disconnect the J28 meter connector.


b.

Disconnect the A3 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J28-14 (SW) - A3-1 (+) Always Below 1 Ω
J28-14 (SW) - Body ground Always 10 kΩ or higher
A3-2 (E) - Body ground Always Below 1 Ω




OK

8.INSPECT COMBINATION METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT COMBINATION METER
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and the Techstream on.


c.

Perform the Active Test of the combination meter (meter CPU) using the Techstream (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Brake Brake warning light ON or OFF Perform the test with the vehicle stopped and engine idling


d.

Check that the BRAKE warning light turns on and off in the combination meter using Techstream.

OK:

The BRAKE warning light turns on and off in accordance with the Techstream operation.




OK

NG

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C160219E02
2.468,0.987 3.207,1.143 0.739,0.156 10 Pushed in 2.468,1.571 3.105,1.727 0.637,0.156 10 Released 0.039,0.023 2.637,0.383 2.598,0.360 10 Component without harness connected: (Parking Brake Switch)

Disconnect the A5 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Switch body ground Parking brake switch ON
(Switch pin released)
Below 1 Ω
1 - Switch body ground Parking brake switch OFF
(Switch pin pushed in)
10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)
a.
U152482E02
0.865,1.615 1.052,1.24 true 0.083,0.104 2.438,0.448 2.354,0.344 10 false Front view of wire harness connector: (to Skid Control ECU) 0.75,3.604 1.021,3.771 0.271,0.167 10 false A5 0.271,1.031 0.542,1.198 0.271,0.167 10 false A17 0.031,2.51 2.406,2.823 2.375,0.313 10 false Front view of wire harness connector: (to Parking Brake Switch) 1.042,1.031 1.448,1.188 0.406,0.156 10 false PKB2

Disconnect the A17 ECU connector.


b.

Disconnect the A5 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-14 (PKB2) - A5-1 Always Below 1 Ω
A17-14 (PKB2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR