Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM27M0U _58 Vehicle Interior _049156 ENGINE IMMOBILISER _0234432 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detected errors in its own communications with the transponder key ECU; 2) the ECM detects errors in the communication lines: or 3) the ECU - ECM communication ID between the transponder key ECU and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are present. If present, troubleshoot the engine immobiliser DTCs first.

DTC Code DTC Detection Condition Trouble Area
B2799 One of following conditions is met:
·

Error in communication between ECM and transponder key ECU

·

Error in communication lines

·

ECU - ECM communication ID is different during communication with transponder key ECU


·

Harness or connector

·

Transponder key ECU

·

ECM



WIRING DIAGRAM

B168146E08
1.073,1.99 1.469,2.313 0.396,0.323 10 false A24 ECM 5.469,0.938 5.865,1.125 0.396,0.188 10 false EFIO 5.469,1.396 5.865,1.583 0.396,0.188 10 false EFII 1.448,0.938 1.844,1.125 0.396,0.188 10 false IMI 1.396,1.406 1.792,1.594 0.396,0.188 10 false IMO 1.771,0.823 2.063,1.031 0.292,0.208 10 false 40 1.771,1.302 2.063,1.51 0.292,0.208 10 false 29 5.188,0.813 5.479,1.021 0.292,0.208 10 false 13 5.198,1.292 5.49,1.5 0.292,0.208 10 false 12 5.208,2.115 6.76,2.458 1.552,0.344 10 false Transponder Key ECU 5.219,1.958 5.677,2.156 0.458,0.198 10 false J26

CAUTION / NOTICE / HINT

HINT:

When the transponder key ECU and/or ECM is replaced, reregister the ECU - ECM communication ID (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>REGISTRATION).


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2799 is not output.




OK

NG

3.REREGISTER ECU - ECM COMMUNICATION ID
3.REREGISTER ECU - ECM COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>REGISTRATION).



NEXT

4.CLEAR DTC
4.CLEAR DTC

NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2799 is not output.




OK

END

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and the transponder key ECU.

OK:

Connectors are properly connected.




OK

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

NG

CONNECT CONNECTOR CORRECTLY

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
B443048E01
0.281,1.406 0.625,1.656 0.344,0.25 0.229,3.604 0.573,3.854 0.344,0.25 1.813,1.646 1.813,2.083 false 1.927,1.635 2.229,2.083 false 2.292,3.615 2.719,3.333 false 2.292,3.844 2.76,3.948 false 0.198,0.281 2.448,0.656 2.25,0.375 10 false Front view of wire harness connector: (to Transponder Key ECU) 0.24,2.458 2.5,2.833 2.26,0.375 10 false Front view of wire harness connector: (to ECM) 0.354,1.448 0.813,1.646 0.458,0.198 10 false J26 0.292,3.646 0.75,3.844 0.458,0.198 10 false A24 1.698,2.125 1.969,2.323 0.271,0.198 10 false EFII 2.198,2.115 2.813,2.313 0.615,0.198 10 false EFIO 2.76,3.26 3.219,3.458 0.458,0.198 10 false IMO 2.792,3.885 3.25,4.083 0.458,0.198 10 false IMI

a.

Disconnect the J26 ECU connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J26-13 (EFIO) - A24-40 (IMI) Always Below 1 Ω
J26-12 (EFII) - A24-29 (IMO)
J26-13 (EFIO) or A24-40 (IMI) - Body ground Always 10 kΩ or higher
J26-12 (EFII) or A24-29 (IMO) - Body ground




OK

8.REPLACE TRANSPONDER KEY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE TRANSPONDER KEY ECU
a.

Temporarily replace the transponder key ECU with a new one (see page Vehicle Interior>ENGINE IMMOBILISER>TRANSPONDER KEY ECU>REMOVAL).



NEXT

9.CLEAR DTC
9.CLEAR DTC

NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2799 is not output A
DTC B2799 is output (for 1UR-FE) B
DTC B2799 is output (for 3UR-FE) C
DTC B2799 is output (for 3UR-FBE) D



A

END (TRANSPONDER KEY ECU IS DEFECTIVE)

B

C

D